Question about 2007 Chrysler Town & Country LX New Cars

Open Question

Courtesy lights in overhead console

How do you change the courtesy light bulbs in the overhead console?

Thanks,

Posted by on

5 Suggested Answers

  • 141 Answers

SOURCE: re: 2004 Honda Accord The

Small srewdriver to either of the longsides will pop the lense out and allow access to the bulbs.

Posted on Jan 11, 2009

  • 1 Answer

SOURCE: courtesy lights won't come on dodge 2500 ram van 1997

Turn the headlight switch anti clockwise until you hear a click

There is a feature to disable the interior lights when the doors are open for camping. (Turn the switch fully clockwise).

Posted on Jan 18, 2009

  • 1 Answer

SOURCE: I want to replace the light bulb in the overhead push light.

If you are referring to the console with the 2 push button lights. There is a screw right in the front near the windshield that you have to unscrew. After doing so use your fingers and get a grip in the console and pull it straight down and you will see the lights. I just had to do the same thing about a week ago. Hope this helps....

Posted on Mar 17, 2009

  • 91 Answers

SOURCE: Rear interior light and door courtesy lights not working- Jaguar

take off the cover and replace them. if you have a volt/ohm meter you can put if on the car side and make sure you have voltage and the ohm meter on the buldb should give a 1 rating if its good. it would be the cheapest and easiest to just get a new bulb and see if it works then start checking fuses if its not the bulb.

Posted on Mar 31, 2009

  • 651 Answers

SOURCE: How can I replace a bulb in the interior map

usually you just pop off the cover and replace the bulb. the covers just snap in place. unless there are screws witch you just unscrew.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 Buick Lucerne and the front reading lamps won't turn off.


Overhead Console Lamp and Roof Rail Courtesy/Reading Lamps
The courtesy/reading lamp is a duel purpose lamp that can be illuminated two different ways. First, the lamp can be turned ON during courtesy lamp operation as described above. Second, the lamps can be turned ON individually for reading lamp operation by the lamp switch. The BCM supplies battery voltage from the INT LAMPS fuse through the inadvertent power courtesy lamps circuit to the courtesy/reading lamps for reading lamp operation only. Ground for the courtesy lamp module or the roof/rail reading lamps is provided at G402

Courtesy Lamps
When either one of the front doors is opened, ground is applied through the door latch door open switch and the door open switch signal circuit to the door module indicting the door open position. In response to this signal, the door module sends a GMLAN serial data message to the BCM of the door open position. Or, when either one of the rear doors is opened, ground is applied through the door latch door open switch and the rear door open switch signal circuit to the BCM is indicating the rear door open position. Once a door open message or signal received, the BCM will then apply battery voltage from the CTSY/RF TRN fuse through the courtesy lamp supply voltage circuits illuminating the lamps listed below:
• Overhead console lamp
• Roof rail courtesy lamps
• Footwell courtesy lamps The BCM receives battery voltage from the INT LAMPS fuse in order to supply power to the inadvertent courtesy lamps. Inadvertent power courtesy lamp feature provides a similar function for the interior lamps as a retained accessory power feature. The BCM will energize the courtesy lamps supply voltage circuit when the BCM is in the active state (awake). When the inadvertent power courtesy lamps supply voltage circuit is energized, it supplies voltage to all the interior lights listed below. The BCM will continue to supply voltage to the interior lamps after the ignition is turned OFF so that the interior lamps may be operated.
• Overhead Console Reading Lamps
• Roof Rail Reading Lamps
• Vanity Mirror Lamps
• I/P Compartment Lamp
• Rear Compartment Courtesy Lamp
In the event that any of these lamps were to remain illuminated for a period of more than 20 minutes with the ignition switch in the OFF position and no BCM input activity, the BCM will deactivate the inadvertent power supply voltage circuit to prevent a total battery discharge condition. The BCM receives battery voltage from the CTSY/RF TRN fuse in order to supply power to the courtesy lamps. The BCM applies this voltage to the courtesy lamps through the courtesy lamp supply voltage circuits. When any door is opened, the door open switch contacts close and the BCM receives a door-open signal. If the BCM receives a door lock or unlock signal, the BCM will activate the courtesy lamp supply voltage circuit, providing battery voltage to the dome lamps and the left and right footwell courtesy lamps. The courtesy lamps can be manually activated by placing the interior lamp switch in the DOME position. For more detailed information concerning courtesy lamp operation refer to Interior Lighting Systems Description and Operation.

Jan 16, 2017 | Buick Cars & Trucks

1 Answer

My interior light won't come on in my 1999 Buick Lesabre. I have checked the bulb & the fuse. Can anyone help me with this problem? Any ideas are sincerely appreciated.


Courtesy Lights
The courtesy lights come on under the following conditions:
?€¢
Any door is opened.


?€¢
The interior lamp switch is in the ON position.


?€¢
The keyless entry transmitter unlocks the doors (illuminated entry).

When the key is removed from the ignition switch with all of the doors closed, the courtesy lights light for approximately 25 seconds before fading out.
Battery positive voltage (B+) is applied at all times through the IP fuse block CTSY LP/PWR MIR fuse 6A via CKT 640 (ORN) through the body control module (MALL) to the courtesy lights via CKT 1732 (ORN). The MALL provides a ground through CKT 156 (WHT) for the courtesy lights under the following conditions:
?€¢
The MALL receives an input from a door being opened.


?€¢
The MALL receives an input from the interior lamp being turned ON.


?€¢
The MALL receives an input from the doors being unlocked using the keyless entry transmitter.

The courtesy lamps then light.
When the courtesy lights are activated by opening and closing a door, the courtesy lights will remain on for approximately 25 seconds before fading out after all of the doors are closed. If the ignition switch is turned to START or RUN within the 25 seconds, the lights immediately begin to fade out. If a door is left open, the MALL removes battery positive voltage (B+) to the courtesy lights after 10 minutes. When the courtesy lights are activated by the interior lamp switch, the lights remain on as long as the interior lamp switch is in the ON position. When the courtesy lights are activated by unlocking the doors using the keyless entry transmitter, the lights remain on for approximately 40 seconds. If the doors are locked using the keyless entry transmitter within the 40 seconds, the lights immediately begin to fade out.
Body Control Module (MALL) Diagnostic Mode
For a detailed explanation of the MALL module diagnostic mode, refer to Body Control Module Cell 51.
What interior light ? Dome , courtesy lights etc....They don't work with switch, keyless entry , door opening ?
What

Dec 03, 2015 | Buick Cars & Trucks

2 Answers

Interior lights not working


You mite have a DTC - diagnostic trouble code stored in the BCM - body control module , The BCM controls the interior lights ! Have you heard of a BCM ?
DTC B2615
The body control module (BCM) receives a ground signal from the door jamb, liftglass/liftgate, or courtesy lamp switches requesting courtesy/dome lamp illumination. When this occurs, the BCM directly sends a voltage through the courtesy lamp supply voltage circuit illuminating the courtesy/dome lamps.
Conditions for Setting the DTC
?€¢
When the BCM receives a courtesy lamp illumination request signal and the courtesy lamp supply voltage circuit is shorted to ground.

?€¢
When the BCM is not receiving a courtesy lamp illumination request signal and the courtesy lamp supply voltage circuit is shorted to voltage or open only to the first splice from the BCM.

?€¢
There is a loss of the rear fuse block TBC 3 battery supply voltage to the BCM for more than 1 second

Diagnostic Aids
?€¢
Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

?€¢
Only an open circuit up to the first splice from the BCM will set DTC B2615.

DTC B3801
The body control module (BCM) monitors the courtesy lamp switch signal circuit in order to determine when the courtesy/dome lamps should be illuminated. When the BCM senses that the courtesy lamp switch signal circuit is grounded when the switch is activated, the BCM will directly illuminate the courtesy/dome lamps. Do you know what a scan tool is ? not a code reader !
Courtesy Lamps Inoperative




GM Tech 2 Training video 1996

Aug 24, 2015 | 2004 Chevrolet Chevrolet TrailBlazer EXT

2 Answers

2009 dts inside lights stay on


this could be a door switch problem or a BCM problem. access the BCM for codes and data this will help. check to make sure the headlight switch for the interior lights is in the off position.

Mar 20, 2015 | 2009 Cadillac DTS

1 Answer

Interior courtesy light


Page 116 and 117 of the manual explain that there's a two-position slide switch on the map light, DOOR and OFF. The back light has three positions, ON, Door Activated, and OFF.

Pages 116 and 117:
http://techinfo.honda.com/rjanisis/pubs/om/ACC080/ACC0808OM.pdf

Dec 12, 2013 | Honda Cars & Trucks

1 Answer

How to change the courtesy light in my 2003 lincoln navigator


You can carefully remove the cover with a small flat screwdriver to get to burned out bulb.

Jan 18, 2013 | 2003 Lincoln Navigator

1 Answer

How to remove Overhead Console on 2000 Jeep Grand Cherokee, due to menu bottons not working


straight from the Jeep service manual

1.) Disconnect negative battery cable.
2.) Remove screws attaching front of overhead console to front of bracket.
3.) Pull console downward from area near courtesy lights. 4.) Disconnect electrical connectors and remove console from vehicle.

To install, reverse removal procedure.

Apr 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

2007 grand caravan sxt. It has the front seat reading lights in the overhead console, actuated by pushing their clear plastic cover. They are also centrally controlled as part of the courtesy light feature...


Remove by starting on the windshield side(pointy side). Using a very small flat blade screwdriver, or small trim stick. Pry slowly to release the 2 clips. Do not do this on the seat side !!! You can break the tab that switches the light on/off. Blub turn out counterclockwise.

Oct 13, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

How do you change the rear reading lamp bulb


  1. Using a thin bladed tool, carefully pry the lamp lens from the overhead console.
  2. Using a thin bladed tool, carefully pry the metal shield inward until the retaining tabs clear the notches.
  3. Remove the metal shield.
  4. Remove the courtesy lamp bulb.

Nov 26, 2008 | 2001 Pontiac Bonneville

Not finding what you are looking for?
2007 Chrysler Town & Country LX New Cars Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...