Question about 2003 Pontiac Aztek

Open Question

Anti-lock break light

My break light is on after putting new breaks all around and new hub and mater cycater.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 82 Answers

SOURCE: 2002 Pontiac Aztek - AWD disable light and Anti Lock Light

AWD disabled from a sensor unit in rear differential that senses high temp. This thing is over $300. Whine is from fluid. Need to change fluid. This versatrack fluid is about $40 per bottle and you need 3 bottles. Thumping noise is from loose rear knuckle bushings. These are part of the entire rear knuckle assy. and you must replace complete knuckle.

Posted on Jun 22, 2009

Ad
BCAS1298
  • 3092 Answers

SOURCE: I cannot get the rear drum off of a 2005 pontiac

Spray some wd-40 and get a bigger hammer, hit it hard you won't damage it.Just be careful not to hit the stud's.

Posted on Jan 19, 2010

  • 613 Answers

SOURCE: i have 2 problems with

you have a brake sensor malfunctioning have to use a voltmeter see which abs sensor is nott functioning one disrupt the whole system they are mounted on the caliper or close by

Posted on Sep 13, 2010

ratsack33
  • 91 Answers

SOURCE: 2002 poNtiac aztek anti lock

Typically means you have lost an anti-lock brake sensor as gone bad.
Take to local garage to get them to scan the computer. Will reveal if that is the problem, which sensor it is, or if problem lies elsewhere.

Posted on Jan 06, 2011

mark_p06
  • 32 Answers

SOURCE: break lights and blinkers not working

If you put the tester on the outlets and it lights up properly but the bulbs dont, you have already concluded that the wiring isn't the problem. unless of course the wires are corroded and simply putting the bulb in shorts it out. Have you tested the bulbs?

Posted on Jul 22, 2012

Testimonial: "Replaced bulbs and everything is working again... Thanks so much mark_p06 for your response!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

ABS an break light stays on I have put on new breaks still on


There is a problem with the ABS system. It will turn on both lights. You need the ABS codes retreived in order to isolate the problem and repair the malfunction. Your normal brakes will work just fine.

Apr 11, 2015 | Cars & Trucks

1 Answer

How to change rear drum breaks to disc breaks


this can be a big job u need new master cylinder, proportioning valve, conversion kit (or donor car) for rear hubs, rotors etc. if has anti-lock brake system gets even more complicated

Nov 14, 2010 | 1995 Ford Thunderbird

2 Answers

1999 Z71 anti lock breaks


the abs module could have dirt in the connection its a common problem or the other side could be corroded or also the speed sensor in the transmission could be faulty

Jan 08, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Anti-lock light comes on along with the break warning light, fluid level good no softening on the break pedel...no identifiable difference in performance but the lights remain on.


ABS ligth coming on for no reason is usually dirty sensors on one of the wheels. can often happen after driving through mud etc, Also the serrated disc which the sensor looks at on the hub can get clogged up causing same problem. brakes will still work ok but you will have no ABS function. I have had limited success with this (very common) problem by pressure washing the wheels and hubs. failing that its a case of wheels off and cleaning it all up by hand. Another cause can be bad connection, cracked/trapped sensor wire. Difficult to tell which wheel its on though.

Sep 05, 2009 | 2000 Mitsubishi Eclipse

2 Answers

Anti-lock brake system and brake system lights goes on


Abs lights staying on probably a broken wire at the wheel hub I just got mine fixed and every time the light comes on it is a broken wire you have to get a shop to put iton an ABS scanner to find the break

Aug 25, 2009 | 2001 Ford Windstar

1 Answer

Anti lock break light on how much is it generaly for front sensor


This could be caused by a fuse being blown or this could mean that your brakes need to be changed.

Jul 08, 2009 | 2003 Chevrolet Malibu

1 Answer

Anti lock light is on


unhook the battery for about ten minutes... that should reset the light... if it comes back on stop in at autozone and have them scan the codes (it's free)

Robert

please take a moment to rate this solution... thanks

Feb 03, 2009 | 1991 Acura Legend

1 Answer

AWL disabled light and anti lock break light


I have the same problem on my 03. AWD Light is caused by your Rear Wheel Hub(s) is going bad. Dealer cost approx is $500.00 or do it yourself, not to difficult for $129.99 part found at Auto Zone

Jan 16, 2009 | 2003 Pontiac Aztek

Not finding what you are looking for?
2003 Pontiac Aztek Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...