Question about Lincoln Town Car

Open Question

How do I replace lincoln town car carpet

I need to remove the trim around doors to access wiring

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

Ad
old marine
  • 1992 Answers

SOURCE: need routing diagram for 2000 lincoln town car serpentine belt

There's a diagram at this link.

Posted on May 11, 2009

  • 4 Answers

SOURCE: Lincoln Town Car 1999 driver side window switch

I have the same problem in my 2001 towncar. I removed the switch control panel (without removing the door panel) by prying up from the front of the panel. There's a spring loaded plug under the mirror adjustment. Once you get that pulled up, the whole unit will lift out. Since there's a two year difference in the models - it MAY not work... however, you might not have to remove the whole door panel as you think.
In my case, the wiring was bad.

Posted on Sep 03, 2009

  • 1 Answer

SOURCE: 2001 lincoln town car winshjield wiper

where is the fuse box for my 2001 lincoln towncar looking for windshield wiper fuse because they wont turn on what so ever

Posted on Dec 24, 2009

c17hydro
  • 2984 Answers

SOURCE: need to remove the dash

Removal & Installation

  1. If equipped, turn the air suspension service switch to the OFF position before raising the vehicle.
  2. Drain the cooling system.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Front seats
    • Carpeting
    • Rear airflow duct
    • Heater hoses
    1. Remove the driver’s side air bag module by removing or disconnect the following:
    2. SRS module-to-steering wheel bolts, from both sides of the steering wheel.
    • SRS module and disconnect the electrical connector
    • Horn switch electrical connector
    1. Remove the passenger’s side SRS module by removing or disconnecting the following:
    2. Open the glove box and disconnect the glove compartment isolator
    • Push inward on the 2 glove box door tabs and lower it
    • SRS module’s electrical connector
    • SRS module-to-instrument panel bolts and the module
    1. Remove the instrument panel by removing or disconnecting the following:
    2. Speed control servo nuts and move the servo aside
    • Bolt and disconnect the left side bulkhead connector
    • Left side bulkhead connector from the dash panel
    • Windshield washer fluid reservoir screw, and position the reservoir aside
    • Blower motor electrical connector
    • Air conditioning pressure cut-off switch electrical connector
    • In-line electrical harness connector
    • Electronic Automatic Temperature Control (EATC) variable blower motor controller electrical connector
    • Right front wheel
    • Right front fender splash shield bolts and move the shield away from the cowl
    • Wiring harness from the evaporator case
    • Wiring harness from the cowl
    • Right side instrument panel lower insulator pushpins, disconnect the power point electrical connector, remove the courtesy lamp from the socket and remove the insulator
    • Unseat the wiring grommet and feed the wiring harness through the cowl
    • Cowl side trim panels and the windshield side garnish moldings from both sides
    • Locking clip and the Electronic Crash Sensor (ECS) module electrical connector
    • Antenna connector
    • Ground wire bolts from the right side
    • EATC hose at the evaporator housing
    • Bolt and disconnect the bulkhead connector from the right side
    • Pull the door weatherstrip seals away from the instrument panel on both sides
    • Tunnel brace trim cover
    • Climate control head vacuum harness connector
    • Instrument panel tunnel brace nuts and the brace
    • Ground wire bolts from the left side
    • Wiring harness connectors from the left side
    • Parking brake switch electrical connector
    • Pry out the instrument panel defroster opening grille, disconnect the electrical connectors and the remove the grille.
    1. Remove or disconnect the following:
    2. 3 upper instrument panel screws
    • Instrument panel cowl side nut from both sides
    • Instrument panel cowl side bolt. From the left side
    • Instrument panel
    • Windshield wiper mounting arm and the pivot shaft
    • Electrical connector and remove the upper cowl extension screw and the extension
    • Vacuum hoses and the wire harness connector from the evaporative emissions canister purge valve
    • Evaporative emissions purge valve nuts and the valve
    • Cowl side nut
    • Right side rear fender apron screws and reposition the apron
    • Evaporator housing nut and screw
    • Vacuum hoses and the wiring harness connectors
    • Plenum chamber’s lower flange nuts
    • Plenum chamber’s upper flange nut and the plenum chamber
    • Heater core cover-to-heater plenum chamber screws and the cover
    • Seal and the heater core
  • Posted on May 26, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How to remove interior trim on passenger side from back to front to install wiring for tow bar


    The trim may have several plugs that hide bolts/screws. Look for those and remove with care using a nail remover or flat object like a putty knife. after removing any screws, the trim may come off or have to be pried off. Some overlaps overs and it is better to remove the ones that are on top first. The rubber trim along the edge is usually pliable and with give. Make sure to remove seatbelts and the like if attached to the same trim. Door trim may not have sufficient space to hold wires but they may have to be moved to access under the carpet or channels where the wires may be run. Be sure to remember the order of removal and retain all fasteners. Be very careful to put it all beck correctly and not to smash or snag any wires. Take special care when running through holes in frame not to allow it to contact sharp edges. Tape over or cover edges where needed.

    For your problem, look for clips around edges that may have to be released.

    Jan 02, 2015 | 2011 Toyota RAV4

    1 Answer

    How to fix LHS front door remote. Lock on holden statesman wl


    more than like if its just on door that wont look and the hoon sounds the door actuator will be faulty and you will need to replace the actuator.
    To do this you will need pull the inside door handle off.
    remove all door trim covers to access screw and disconnect mirror wiring.
    remove all screws around door trim.
    very carefully remove door trim once the trim is off you see a plastic inner door liner don't rip gently remove half .
    look inside door and you will see the door actuator and lock,carefull lift up locking tabs so you can remove all door rods from actuator.
    on the outside of door undo the 3 bolts and actuator will come out.
    get the new actuator and fit it the same way the old one come out.
    Before refitting the trim grab some silicon and reseal plastic to door to keep water out..

    Dec 06, 2014 | Holden Cars & Trucks

    1 Answer

    I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


    Answer
    FRONT DOOR TRIM PANEL
    REMOVAL
    Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
    Disconnect wire connector from courtesy lamp.
    If equipped, remove screws attaching door assist handle to inner door panel.
    If equipped, remove screw attaching door pull cup to inner door panel.
    If equipped, remove screws attaching trim panel to door from below map pocket.
    If equipped, remove window crank.
    Using a trim stick, remove screw cover from switch panel.
    Remove screws attaching switch panel to door trim.
    Remove power accessary switch from door trim Front Door Switch Panel
    Disconnect power switch from wire connector.
    If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
    If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
    Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
    Lift trim panel upward to disengage flange from inner belt molding at top of door.
    Tilt top of trim panel away from door to gain access to latch linkage.
    Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
    Separate linkage rod from latch handle.
    Remove front door trim panel from vehicle.
    INSTALLATION
    Hold top of trim panel away from door to gain access to latch linkage.
    Place linkage rod in position on latch handle.
    Engage clip to hold linkage rod to inside latch release handle.
    Place front door trim panel in position on door.
    Install trim panel into inner belt molding at top of door.
    Install clips to attach door trim to door frame around perimeter of panel.
    If equipped, install screw to attach door trim to door panel behind inside latch release handle.
    If equipped, connect power switch into wire connector.
    Place power accessary switch in position on door trim.
    Connect wire connector into memory seat/mirror switch and install switch into trim panel.
    Install screws to attach accessary switch panel to door trim.
    Install screw cover into switch panel.
    If equipped, install window crank.
    If equipped, install screws to attach trim panel to door inside map pocket.
    If equipped, install screw to attach door pull cup to inner door panel.
    If equipped, install screws to attach door assist handle to inner door panel.
    Connect wire connector into courtesy lamp.
    Install lamp in door trim.

    Feb 02, 2012 | 2000 Dodge Caravan

    1 Answer

    How to remove door panel on 2003 grand caravan



    1. Remove the plug and remove screw attaching door pull cup to inner door panel.
    2. Remove the switch bezel and then disconnect the power window-memory switch.
    3. Now you need to remove the screws attaching the trim panel to the door from below map pocket.
    4. If you have a window crank remove this now.
    5. Remove the screw holding the door trim to the door panel from behind -inside latch release handle .
    6. Now disengage the clips attaching the door trim to the door frame around the outside of the panel.
    7. Lift the trim panel upward to disengage the flange from the inner belt molding at the top of the door.
    8. Now tilt the top of trim panel away from door to gain access to the linkage on the latch.
    9. Now you need to disengage the clip that attaches the linkage rod to the inside latch release handle - this is the inside door handle linkage.
    10. Now just separate the linkage rod from the latch handle.
    11. Now you disconnect the power door switch and the courtesy lamp connectors.
    12. Now you can remove the door trim panel up and out.


    • Hope this helps and thank you for using FixYa.

    Regards, Tony

    Jul 23, 2011 | 2003 Dodge Caravan

    1 Answer

    How to replace rear blower motor motor in 2006 chrysler town and country van


    from autozone.com:


    Removal & Installation

    1. Disconnect and isolate the negative battery cable.
    2. Remove the right quarter trim panel as follows:
      1. Remove first rear seat. Remove the second rear seat, if equipped.
      2. Remove the sliding door sill plate.
      3. Remove the quarter trim bolster.
      4. Remove the upper C-pillar trim and D-pillar trim panel.
      5. Remove the first and second rear seat belt anchors.
      6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
      7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
      8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


    jturcotte_39.gif
    Fig. Removing the trim panel to access the rear blower motor

    i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


    j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


    k. Pull first rear seat belt through the access hole.


    l. Remove the quarter trim panel from the vehicle.



    3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


    4. Twist the blower motor out of scroll housing.


    5. Disconnect the blower motor wiring connector.


    6. Remove the blower motor from vehicle.

    jturcotte_40.gif
    Fig. The rear blower motor is held in place by four screws
    To install:

    1. Install the blower motor unit into the vehicle.
    2. Reconnect the blower motor wiring connector.
    3. Secure the blower motor into scroll housing.
    4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
    5. Install the right quarter trim panel as follows:
      1. Install the quarter trim panel in position in the vehicle.
      2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
      3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
      4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
      5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
      6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
      7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
      8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
      9. Install the D-pillar trim panel and upper C-pillar trim.
      10. Install the quarter trim bolster.
      11. Install the sliding door sill plate.
      12. Install the second rear seat, if equipped, and install the first rear seat.
    6. Reconnect the negative battery cable. Check blower motor operation.

    Nov 04, 2010 | Chrysler Town and Country Cars & Trucks

    1 Answer

    How to replace the blower motor in a dodge 2001 caravan


    Removal & Installation
    1. Disconnect and isolate the negative battery cable.
    2. Remove the right quarter trim panel as follows:
      1. Remove first rear seat. Remove the second rear seat, if equipped.
      2. Remove the sliding door sill plate.
      3. Remove the quarter trim bolster.
      4. Remove the upper C-pillar trim and D-pillar trim panel.
      5. Remove the first and second rear seat belt anchors.
      6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
      7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
      8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

        1549e60.jpg

        Fig. Removing the trim panel to access the rear blower motor

      9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
      10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
      11. Pull first rear seat belt through the access hole.
      12. Remove the quarter trim panel from the vehicle.
    3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
    4. Twist the blower motor out of scroll housing.
    5. Disconnect the blower motor wiring connector.
    6. Remove the blower motor from vehicle.

      823bf07.jpg

      Fig. The rear blower motor is held in place by four screws


    To install:
    1. Install the blower motor unit into the vehicle.
    2. Reconnect the blower motor wiring connector.
    3. Secure the blower motor into scroll housing.
    4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
    5. Install the right quarter trim panel as follows:
      1. Install the quarter trim panel in position in the vehicle.
      2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
      3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
      4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
      5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
      6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
      7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
      8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
      9. Install the D-pillar trim panel and upper C-pillar trim.
      10. Install the quarter trim bolster.
      11. Install the sliding door sill plate.
      12. Install the second rear seat, if equipped, and install the first rear seat.
    6. Reconnect the negative battery cable. Check blower motor operation.

    Hope helps (remember to rate this).

    Nov 01, 2010 | 2000 Dodge Caravan

    2 Answers

    Removing/installing 2000 dodge grand caravan window glass


    after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps

    Sep 05, 2009 | 2004 Dodge Caravan

    1 Answer

    Passenger side view mirror broke and trimming around window


    On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door.

    As for the trim, you should just be able to wedge it back in place into the door

    Jul 30, 2009 | 2003 Toyota Corolla

    3 Answers

    How do i replace the window motor


    This is a common problem with driver side window. Its just a wear and tear problem. Don't go to the dealership, the Regulator will cost you over $230. Go to Amazon.com and search for the part number which should cost you only $70-80 or so. If you go to a glass place they will charge you dealership price plus $150 per hour. I say do it yourself which goes a little something like this.

    TRIM PANEL
    REMOVAL

    (1) Remove the plug and remove screw attaching
    door pull cup to inner door panel.
    (2) Remove switch bezel and disconnect power window/
    memory switch.
    (3) Remove screws attaching trim panel to door
    from below map pocket.
    (4) If equipped, remove window crank. (Refer to 23
    - BODY/DOOR - FRONT/WINDOW CRANK -
    REMOVAL)
    (5) Remove screw holding door trim to door panel
    from behind inside latch release handle.
    (6) Disengage clips attaching door trim to door
    frame around perimeter of panel.
    (7) Lift trim panel upward to disengage flange
    from inner belt molding at top of door.
    (8) Tilt top of trim panel away from door to gain
    access to latch linkage.
    (9) Disengage clip attaching linkage rod to inside
    latch release handle (Fig. 13).
    (10) Separate linkage rod from latch handle.
    (11) Disconnect the power door switch, courtesy
    lamp electrical connectors.
    INSTALLATION
    (1) Hold top of trim panel away from door to gain
    access to latch linkage.
    (2) Place linkage rod in position on latch handle.
    (3) Engage clip to hold linkage rod to inside latch
    release handle.
    (4) Place front door trim panel in position on door.
    (5) Install trim panel into inner belt molding at
    top of door.
    (6) Install clips to attach door trim to door frame
    around perimeter of panel.
    (7) If equipped, install screw to attach door trim to
    door panel behind inside latch release handle.
    (8) If equipped, connect power switch into wire
    connector.
    (9) Place power accessary switch in position on
    door trim.
    (10) Connect wire connector into memory seat/mirror
    switch and install switch into trim panel.
    (11) Install screws to attach accessary switch
    panel to door trim.
    (12) Install screw cover into switch panel.
    (13) If equipped, install window crank.
    (14) If equipped, install screws to attach trim
    panel to door inside map pocket.
    (15) If equipped, install screw to attach door pull
    cup to inner door panel.
    (16) If equipped, install screws to attach door
    assist handle to inner door panel.
    (17) Connect wire connector into courtesy lamp.
    (18) Install lamp in door trim.
    (19) Install switch bezel.

    WINDOW REGULATOR
    REMOVAL

    (1) Remove the watershield. (Refer to 23 - BODY/
    DOOR - FRONT/WATERSHIELD - REMOVAL)
    (2) Remove door glass retaining clips and secure
    the window in the up position using masking tape or
    equivalent (Fig. 15).
    (3) Disconnect wire connector from power window
    motor, if equipped.
    (4) Loosen screws attaching front and rear window
    guide rails to inner door panel (Fig. 16).
    (5) Remove screw heads on guide rails from key
    hole slots in inner door panel.
    (6) Loosen screws attaching regulator to inner door
    panel.
    (7) Remove regulator from inner door panel.
    (8) Extract rear guide rail through inner door
    panel rear access hole (Fig. 17).
    (9) Extract front guide rail through front access
    hole.
    INSTALLATION
    (1) Insert front guide rail through front access
    hole.
    (2) Insert rear guide rail through rear access hole.
    (3) Place window regulator in position on inner
    door panel.
    4) Place screw heads on guide rails in position
    through key hole slots in inner door panel.
    (5) Tighten screws to attach front and rear guide
    rails to inner door panel.
    (6) Connect wire connector into power window
    motor, if equipped.
    (7) Install door glass.
    (8) Verify door glass alignment and operation.
    (9) Install sound shield and door trim panel. __________________
    Avatar: EconoVoyager Concept
    2001 Dodge Grand Caravan Sport 3.3L
    2004 Chrysler Pacifica AWD 3.5L post_thanks.gif quote.gif

    Apr 05, 2009 | 1998 Dodge Grand Caravan

    1 Answer

    The window fell off it rollers


    1. Remove all door inside handles.
    2. Remove the door inside locking rod knob.
    3. On styles with door pull handles, remove the screws inserted through the handle into the door panel.
    4. On styles with remote control mirror assemblies, remove the remote mirror escutcheon and disengage the end of the mirror control cable from the escutcheon.
    5. On styles equipped with switch cover plate in the door armrest, remove the screws securing the cover plate, then disconnect the switches and cigar lighter, if so equipped, from the harness connectors.
    6. Remove the remote control cover plates and remove the exposed screws securing the cover plate to the door inner panel.
    7. On styles with integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. On some styles it may be necessary to remove the screws behind the armrest deflector or courtesy lamp remote control cover plate. On styles with armrest applied after the door trim installation, remove the armrest to door inner panel attaching screws.
    8. On styles with with two piece trim panels, disengage the retainer clips at the front and rear of the upper trim panel. Remove the upper trim panel by lifting upward and sliding slightly rearward to disengage the the front door inner panel at the beltline.
    9. On styles with electric switches located in the door trim panel, disconnect the wire harness at the switch assembly.
    10. To remove the lower trim panel, remove the attaching screws along the upper edge of the lower trim panel. Then starting at a lower corner, insert a pry type tool between the door inner panel and the trim panel and disengage the retaining clips down both sides and across the bottom. On styles with courtesy lamps or reading lamps located in the trim panel, disconnect the wire harness at the lamp assembly.
    11. On styles with one piece trim panels, remove all the clips around the perimeter of the trim panel. Push the trim panel downward and outboard to disengage it from the door inner panel at the beltline. Disconnect any courtesy lamp wire harnesses, if so equipped and remove the trim panel from the door.
    12. Installation is the reverse of removal. On styles with adjustable trim supports at the beltline, the door trim panel can be adjusted in or out so as not to restrict door window operation.

    Oct 14, 2008 | 1988 Cadillac Sedan DeVille

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    60 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lincoln Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    fordexpert

    Level 3 Expert

    5537 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Lincoln Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...