Question about 2001 Nissan Pathfinder

Open Question

Where is the bank 2 sensor 2 oxygen sensor - 2001 Nissan Pathfinder

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
BCAS1298
  • 3092 Answers

SOURCE: Dear Sir, I have Murano

Bank 2 sensor 1, sensor 1 will be the front one, hope this was very helpful.

Posted on Aug 19, 2010

Testimonial: "thank you"

Ad
jimmybrown67
  • 835 Answers

SOURCE: 1st error: p0136 oxygen sensor circuit bank 1

around 300.00 -400.00 est. at dealer garage maybe little cheaper not much more

Posted on Nov 02, 2010

angelo_mlc
  • 1035 Answers

SOURCE: where is the bank one sensor 2 oxygen sensor

The diagram below is from the Factory Service Manual for a 2001.0 year Pathfinder. The rear oxygen sensors are parts 1 and 3. They are easy to spot from under the car, in the region of the front wheels.


angelo_mlc.jpg

Posted on Nov 06, 2010

  • 249 Answers

SOURCE: HO25- heated oxygen sensor control

check your fuse box for a blown fuse, if not it could be the sensor is bad

Posted on Feb 13, 2011

  • 251 Answers

SOURCE: Hi i have the same

Description : The adaptive fuel Strategy continuously monitors fuel delivery hardware. The test fails when the adaptive fuel tables reach a rich calibrated limit. Now that we have an Idea of what the codes mean , we need to narrow them down. More than likely the problem is causing both codes to set. Keeping this in mind, lets concentrate on Code PO1309. Of the possible causes listed above I see two Sensors that may throw up a lean code. I would look at the MAF Sensor first and then the Temp Sensor. You may find that if you remove the internal Sensor from the MAF Case that some degree has collected on the thin wire. If you find debree, use a Q-Tip to clean it. DO NOT USE CHEMICALS TO CLEAN IT. If no debree is found, try a Known Good MAF Sensor. Still no fix, move on to testing the rest of the Sensors on the list till you find the problem. Keep in mind that the check engine light will have to be cleared after you have fixed the problem.

Posted on Jun 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is P0157 code for 2006 saturn Vue


Bank 2 sensor 2 fault. That would be the downstream oxygen sensor for bank 2.

Aug 03, 2015 | Saturn Cars & Trucks

Tip

Which Oxygen Sensor Is It?


There are many inquiries online about which oxygen sensor to change. Oxygen sensor failure codes are very common on a lot of vehicles. With all of today's vehicles having at least two oxygen sensors and many having three or four of them, it can be a little confusing as to which one is causing the problem.

Before we get into which sensor is which, we need to have a little discussion about oxygen sensor fault codes. There are several different types of oxygen sensor fault codes. Here are just some of the most common ones:

P0135 "Oxygen Sensor Heater Circuit Bank1 Sensor 1"
P0141 "Oxygen Sensor Heater Circuit Bank 1 Sensor 2"
P0147 "Oxygen Sensor Circuit Bank 1 Sensor 3"
P0152 "Oxygen Sensor Voltage High Bank 2 Sensor 1"
P0159 "Oxygen Sensor Slow Response Bank 2 Sensor 2"
P0171 "Oxygen Sensor Lean Sensor 1 Bank 1"
P0172 "Oxygen Sensor Lean Sensor 1 Bank 2"
P0174 "Oxygen Sensor Rich Sensor 1 Bank 1"
P0175 "Oxygen Sensor Rich Sensor 1 Bank 2"

There are many more possible oxygen sensor codes, but I only listed these to make my point. Many times the oxygen sensor code is NOT caused by the oxygen sensor itself. "Lean" or "Rich" oxygen sensor codes (i.e. P0171, P0174) are usually caused by something other than the oxygen sensor. Something is wrong, causing the engine to run lean (not enough fuel or too much air) or causing the engine to run rich (too much fuel or not enough air). In these cases, replacing the oxygen sensor will not fix a thing. (That is, unless you are trying to fix your bank account from having too high of a balance!) The new oxygen sensor will just set the same code as the original one. This is because the oxygen sensor is not CAUSING the problem, it is only REPORTING the problem.

High voltage codes (like P0152 above) can be caused by the oxygen sensor wires being shorted to another wire inside the wiring harness. Sometimes these codes are caused by bad grounds where some other component is trying to ground through the oxygen sensor circuit. Again, replacing the oxygen sensor will not fix this! In short, the problem needs to be diagnosed before running out and buying an oxygen sensor.

Just because a fault code has "Oxygen Sensor" or "O2 Sensor" or "O2S" in its description does not necessarily mean that an oxygen sensor needs to be replaced. Many do-it-yourselfers believe that all there is to fixing the car is to hook it to the "magic box", collect the fault codes and replace the parts the computer tells you to replace. There is nothing further from the truth.

Fault codes only point you toward which SYSTEM is failing. The system must be diagnosed to find the CAUSE of the failure. If this is not done properly, it will only result in wasting a bunch of your money. This is what you were trying to avoid by doing it yourself!

So, after reading all of the above, if you think you still want to replace an oxygen sensor, but don't know which one; here is how to figure it out:

Oxygen sensors are always numbered like this:

Bank 1 Sensor 1
Bank 2 Sensor 1
Bank 1 Sensor 2
Bank 2 Sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:

Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder #1 is located and, of course, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only one bank and it is always referred to as Bank 1. The exception to the 4 cylinder rule is on certain 4 cylinder engines (specifically, some Toyotas) there are two catalytic converters used. In this case, Bank 1 sensors will still be in the pipe for the catalyst that is connected to cylinder #1 and Bank 2 sensors will be in the other one.

Sensor 1 is always the "upstream" sensor (the one located BEFORE the catalytic converter).
Sensor 2 is always the "downstream" sensor (the one that is located AFTER the catalytic converter).
Sensor 3 refers to the ONLY "downstream" sensor where there are two sensors before the catalyst and only one after the catalyst. On very few vehicles the reference to this reads "Bank 1 Sensor 3".

If you do not know where cylinder #1 is, then you need to get a diagram of the firing order for your engine. Just post a question on FixYa.com and make sure you give the YEAR, MAKE, MODEL, and ENGINE SIZE of your vehicle and one or more of our experts will be happy to tell you how to find cylinder #1.

- DTTECH
ASE Certified Master Automobile Technician


Also check out this article by dttech: What Else Could Be Wrong?

on Apr 29, 2011 | Ford F-150 Cars & Trucks

1 Answer

Code p0036


Possible causes
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 harness is open or shorted
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Engine Control Module (ECM)


Read more: http://engine-codes.com/p0036.html#ixzz2ib20bfW1

Oct 23, 2013 | Cars & Trucks

1 Answer

2002 toyota avalon engine check light on P0078 and P007C


P0050 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 1)

P0051 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 1)

P0052 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 1)

P0053 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 1)

P0054 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 2)

P0055 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 3)

P0056 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 2)

P0057 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 2)

P0058 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 2)

P0059 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 1)

P0060 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 2)

P0061 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 3)

P0062 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 3)

P0063 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 3)

P0064 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 3)

P0065 Air Assisted Injector -Range/Performance

P0066 Air Assisted Injector -Circuit Malfunction or Circuit Low

P0067 Air Assisted Injector -Circuit High

P0068 (MAP) Manifold Absolute Pressure /(MAF) Mass Air Flow - Throttle Position

Correlation

P0069 (MAP) Manifold Absolute Pressure / (BARO)Barometric Pressure Correlation

P0070 Ambient/Outside Air Temperature Sensor -Circuit Malfunction

P0071 Ambient/Outside Air Temperature Sensor -Range/Performance Problem

P0072 Ambient/Outside Air Temperature Sensor -Circuit Low Input

P0073 Ambient/Outside Air Temperature Sensor -Circuit High Input

P0074 Ambient/Outside Air Temperature Sensor -Circuit Intermittent

P0075 Intake Valve Control Solenoid Circuit Malfunction (Bank 1)

P0076 Intake Valve Control Solenoid Circuit Low (Bank 1)

P0077 Intake Valve Control Solenoid Circuit High (Bank 1)

P0078 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 1)

P0079 Exhaust Valve Control Solenoid Circuit Low (Bank 1)

P0080 Exhaust Valve Control Solenoid Circuit High (Bank 1)

P0081 Intake valve Control Solenoid Circuit Malfunction (Bank 2)

P0082 Intake Valve Control Solenoid Circuit Low (Bank 2)

P0083 Intake Valve Control Solenoid Circuit High (Bank 2)
P0084 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 2)

Mar 22, 2013 | 2002 Toyota Avalon

2 Answers

P0037. heater sen. where is it on the engine?


The code is for the heater in the O2 sensor bank one sensor two. That would be the sensor after the catalytic converter on bank one.
It could be the sensor itself or the power supply for the heater.

Aug 25, 2012 | 2006 Mazda MPV

1 Answer

What is the best way to remove O2 sensor bank 1 sensor 2?


Here is the low-down on oxygen sensors, and their location designations explained:

Oxygen sensors are screwed into the exhaust system at various points. Some people say that there are 4 oxygen sensors, but technically, that is not correct. Only the front 2 are considered oxygen sensors.

These oxygen sensors are screwed into the exhaust pipe or directly into the exhaust manifold, one on each bank. Because they are in front of the catalytic converter, this is often referred to as 'upstream'.

The other 2 are actually called catalyst monitors. They are oxygen sensors, but they serve a different purpose. They monitor the activities of the catalytic converters, thus the name, catalyst monitors. They are screwed into the exhaust one on each bank, after, or downstream, of the catalytic converters.

On a 4 cyl engine, there are only a total of two such sensors, the one in front of the catalytic converter is the O2 sensor, the one behind the cat is the catalyst monitor.

The location names for them are as follows:
  • On a 4 cyl, the front / upstream is called "bank 1 sensor 1" and the rear / downstream sensor is called "bank 1, sensor 2."

  • On a V6 or V8 engine:

    • the passenger side bank on a forward facing engine, or the bank closest to the firewall on a transverse mounted engine, is bank number 1, so the forward / upstream sensor on that bank would be "bank 1, sensor 1."

    • The driver's side bank (forward facing mount engine), or front bank (transverse engine) would be bank number 2, thus the forward / upstream sensor on that bank would be "bank 2, sensor 1," and the rearmost / downstream sensor on that bank would be "bank 2, sensor 2."

Jul 28, 2012 | 2004 Mitsubishi Endeavor

2 Answers

Where is the bank 1 sensor 1 o2 sensor located in a 2006 hyundai sontata gls v6?


The bank has to do with which side of the engine. The 'Sensor 1' indicates that it is upstream of the catalytic converter.

Heated Oxygen Sensor Removal & Installation Heated Oxygen Sensor (Front) (2.4L) hyundai-04-24-5822.gif

Heated Oxygen Sensor (Rear) (2.4L) hyundai-04-24-5823.gif

Heated Oxygen Sensor (Bank 1/Sensor 1) (3.3L) kia-04-00-5213.gif

Heated Oxygen Sensor (Bank 1/Sensor 2) (3.3L) kia-04-00-5214.gif

Heated Oxygen Sensor (Bank 2/Sensor 1) (3.3L) kia-04-00-5215.gif

Heated Oxygen Sensor (Bank 2/Sensor 2) (3.3L) hyundai-04-33-5855.gif

prev.gif next.gif

Jan 13, 2011 | 2006 Hyundai Sonata

1 Answer

Subaru wrx impreza showing fault code p0037. how do i fix this fault which sensor is it and where is the sensor located?


http://helpforcars.net/obd_codes/codes.php?code=P0037

It's an O2 sensor according to the above link, and it is bank 1 sensor 2 low, the 2 meaning that it is downstream past the catalytic converter but not on the manifold.

- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM) Possible Solution Tech Notes The code means that there is a problem with the heater element circuit of the heated oxygen sensor. Water getting inside the heated oxygen sensor connector can caused the heated oxygen sensor fuse to blow, which is a very common problem for this type codes. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors.
Good luck on this repair.

Jan 01, 2011 | 2001 Subaru Impreza

2 Answers

Bank 1 sensor 2 location on a 1996 chevy suburban


zjlimited_210.jpg

Fig. Fig. 3: Oxygen sensor-4.3L engines


zjlimited_211.jpg


Fig. Fig. 4: Oxygen sensor-5.0L and 5.7L engines





zjlimited_212.jpg



Fig. Fig. 5: Oxygen sensor-7.4L engines




Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (the one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).



Dec 12, 2010 | Chevrolet Suburban Cars & Trucks

1 Answer

My check engine light has come on in my 2006 Pontiac G6 after 2 and a half years. What could possibly be wrong since I keep my car serviced and the guys had just told me that my car was in tip top shape?


P0016 - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A
P0030 - Heated Oxygen Sensor (H02S) Heater Control Circuit Bank 1 Sensor 1
P0031 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 1
P0036 - Heated Oxygen Sensor (HO2S) Heater Control Circuit Bank 1 Sensor 2
P0037 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 2
P0050 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 1
P0051 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 1
P0053 - HO2S Heater Resistance Bank 1 Sensor 1 (PCM)
P0054 - HO2S Heater Resistance Bank 1 Sensor 2 (PCM)
P0056 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 2
P0057 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 2
P0068 - Throttle Body Airflow Performance (PCM)
P0100 - MAF Sensor Circuit Insufficient Activity

Jun 25, 2009 | 2006 Pontiac G6

Not finding what you are looking for?
2001 Nissan Pathfinder Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...