Question about 2004 Chrysler Pacifica

1 Answer

04 Pacifica blower motor stays on full blast..changed relay...still going...any thoughts?

04 Pacifica blower motor stays on full blast..changed relay...still going...

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check cooler temperature sensor

Posted on Jan 02, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: cooling fan relay placement 05 pacifica

IF YOU OPEN THE HOOD ON THE RIGHT SIDE THERE IS A SQUAR BOX THAT SITS RIGHT NEXT TO THE BATTERY OPEN THAT BOX AND LOOK UNDER THE PART YOU OPEN AND IT HAS A DIAGRAM AND THE NUMBER WHERE IT GOES

Posted on Dec 29, 2008

  • 1596 Answers

SOURCE: 2005 Town Country front blower motor inop fuse/relay ok

Break Down And Replace The Blower Motor


REMOVAL

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIR-BAG SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN AN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY OR DEATH OR DEATH.

NOTE: The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel.
  3. Position the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.
    1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
    2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.
    3. Push the rubber grommet through the opening in the lower air inlet housing.
    4. Route the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
    5. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
    6. Gently flex the recirculation air door downward to gain access to remove the blower motor from the HVAC housing. NOTE: To aid in installation, note the position of the blower motor mounting tabs prior to removal
      1. Remove the blower motor from the HVAC housing by rotating and tilting the blower motor as necessary.
      INSTALLATION

      1. Gently flex the recirculation-air door downward to gain access to install the blower motor into the HVAC housing.
      2. Position the blower motor to the HVAC housing and tilt and rotate the blower motor as necessary to install it into the HVAC housing.
      3. Align the blower motor mounting tabs to the locations noted during removal and install the three screws that secure the blower motor to the HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      4. Route the blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet.
      5. Position the recirculation door pivot shaft into the lower air inlet housing and install the inlet housing.
      6. Install the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      7. Install the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing. Tighten the screw to 2 N·m (17 in. lbs.).
      8. Connect the blower motor wire lead connector to the blower motor resistor or power module, depending on application.
      9. Install the recirculation door actuator.
      10. Reposition the carpet.
      11. Install the passenger side cowl trim panel.
      12. Reconnect the negative battery cable.
      13. Perform the heater-A/C control calibration procedure.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: 2004 chrysler pacifica, front blower not working,

replace restor open glove box uplug 4 wire plug and two wire plug put 12 volts two wire plug to mke sure fan works if it does replace restor

Posted on Dec 27, 2009

  • 3 Answers

SOURCE: 04 pacifica blower runs on high even when heater

bad relay switch

Posted on Aug 29, 2010

  • 62 Answers

SOURCE: we have a 2004 chryler

you may have to replace the reostat that operates blower fan speeds. check fuse first

Posted on Jun 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Chrysler pacifica AC/HEATER continuously blows with power button in off position


sounds like a blower motor resistor or bad relay. Blower motor resistor is so you don't burn up the blower motor.

Aug 05, 2016 | Cars & Trucks

1 Answer

Replaced Blower Motor and Resistor.AC works but the Blower Motor relay Keeps melting.


So you need a repair shop or dealer to do the
required testing to find & resolve ALL wiring
& electrical problems

You do not want a guess from an internet site
Doesn't work that way

Need wiring diagrams,lots of your time to explain the
issues & some detailed & possibly lengthy & for you,costly
labor time, to just find the main issue

Jul 16, 2014 | 2001 Dodge Durango

1 Answer

2002 GMC YUKON CLIMATE CONTROL FAN STAYS ON, I HAVE NO CONTOL ON DASH UNTIL BATTERY DISCONNECTED


Hello Budd, my name is Andy i need you todo something for me first check all the fuses including the ones located under the hood and the ones located under the steering column and see if all of them are good then if everythinglooks good you have a bad climatepanel.....

Jan 03, 2014 | 2002 GMC Yukon

1 Answer

04 pacifica front blower stopped working,back blower works doing a delay count down


chances are it is the blower motor resistor, it is located under the glove box and can be identified as the small object that the fan wires connect to and since it is cooled by the blower you can reach in and make sure the fan blades will turn if you push them. blower are known to go out but that is usually due the bearings wearing out and it would have been screeching loudly for the last several months. if you want to check the fan motor you can make sure it physically spins and check for resistance on the 2 wires with a multimeter.
if you decide to replace the resistor yourself (which should take 15 min) buy the part from a local store as there are 2 different blower motor resistors used in 04 and 05 pacifica and no good way to identify the 2 different versions you can return the wrong part and present them with the part you removed from the car for them to match up

Dec 13, 2013 | 2004 Chrysler Pacifica

2 Answers

The heater/air conditioner in my 2002 Impala is broken.


Check the blower motor relay first. Next the fan switch and third the blower motor

Mar 05, 2010 | 2006 Chevrolet Impala

1 Answer

Pug 205 1987 Blower not Blowing


IT COULD BE BLOWER MOTOR NOT GROUNDED.YOUR BLOWER MOTOR FUSE AND RELAY COULD BE BAD.MAKE SURE POWER IS GOING TO BLOWER.MOTOR.CHECK TO SEE IF POWER IS GOING TO SWITCH IF SO SWITCH COULD BE BAD.HOT WIRE BLOWER MOTOR USING JUMPER WIRE AND POWER FROM THE BATTERY.IF BLOWER MOTOR WORKS.YOU HAVE FUSE RELAY AND SWITCH PROBLEM.MOST THE TIME WHEN RESISTOR BAD.YOUR BLOWER MOTOR ONLY WORK ONE SPEED SOME TIME.

Sep 03, 2009 | 1989 Peugeot 405

1 Answer

AC rund at full blast even while turned off.


You need a blower motor resistor. This will take care of the problem. It is located behind the glove box. Pull it down, and you will see a plug going into the heater box. Two screws, and that is it.

Mar 05, 2009 | 1998 Chrysler Town & Country

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...