Question about Cars & Trucks

1 Answer

On my 2008 kx100 where do I put brake fluid in it and where is it located?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,156 Answers

Either on top of the brake master cylinder or if mounted well down it could be up nearer the top so look for feeder tube to the master cylinder ,failing which look in the manual

Posted on Dec 31, 2012

  • chelsea williams Jan 01, 2013

    I can't get rear brakes. I've pumped the heck out of the brake pedal but still have no brakes. Do I just need to keep pumping and bleeding it til I get some?

  • Colin Stickland
    Colin Stickland Jan 01, 2013

    No definatly not you need to firstly slacken the handbrake cable then remove the rear drums ,clean the rusty lip the manually adjust the the brakes ,if still no brake pedal then renew the master sylinder as its a tandem master and has a seal in the middle between the two chambers and whats happening is the seal has failed ,renewing the cylinder is the only answer ,fairly common fault on high milage cars over 4 yrs of age

×

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: location of the brake fluid input

You'll also need to drain and flush both systems as the two fluids are incompatible. Brake fluid (DOT3, etc.) goes into the brake master cylinder (located directly in front of the brake pedal, except inside the engine compartment...on the left hand side). Power steering fluid should go into the power steering pump reservoir mounted directly to the pump or in a remote location somewhere near the pump. Usually the power steering pump is located on the front of the engine near the fan/serp. belts.

Posted on Feb 08, 2010

sandman357
  • 236 Answers

SOURCE: Brake Fluid for 2008 Avenger

it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.

Posted on Feb 22, 2010

Testimonial: "Quick response, guided me in the right direction. Thanks!"

emissionwiz
  • 76164 Answers

SOURCE: Location of brake fluid reservoir in a 2008 Chrysler Sebring 2.4L

Driver side under the hood.

Posted on Oct 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 jetta master cylinder location


Under brake fluid container..driver side near wipers usually

Aug 26, 2014 | 2008 Volkswagen Jetta

1 Answer

Do the 2008 chevy hhr have brake fluid


Your 2008 Chevy HHR does take brake fluid. The fluid type is DOT-3 Brake Fluid. The brake fluid reservoir is a small white plastic container. The cap will read DOT-3 or brake fluid, on it. This reservoir will be found against the drivers side firewall. I hope this helps you. Your owners manual has this information inside, if it is available.

Jan 18, 2014 | Cars & Trucks

1 Answer

Where is the transmission fluid reservoir located in a 2008 dodge avenger?


Has no one even read his question? How do brakes have anything to do with Transmission Fluid Reservoir?

Oct 24, 2012 | 2008 Dodge Avenger

1 Answer

Brake Fluid for 2008 Avenger


it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.

Feb 22, 2010 | 2008 Dodge Avenger

2 Answers

Location of the brake fluid input


the brake fluid resivoir is above the master cylinder on the firewall. so on the left side near the windshield. the power steering resivoir is closer to the front end and is distinguished by not being connected to the master cylinder..

Feb 08, 2010 | 1987 Mercedes-Benz 300-Class

2 Answers

My 2008 dodge avenger emergency brake light goes off and on every day. what does that mean. the brake is down and off


check the fluid level in the master cylinder,the sensor will turn the same light on,or you might need the e brake switch adjusted

Jan 29, 2010 | 2008 Dodge Avenger

1 Answer

My 2008 Corolla LE brake light is on but no brake problems


Usually when it is on, it is due to either low brake fluid, e-brake is not full disengaged, or abs pump or circuit is faulty.

Nov 15, 2009 | 2008 Toyota Corolla

1 Answer

Power steering fluid added to brake fluid. Where are the two well openings located in relation to each other? How can I get the person who caused the damage pay?


well there are no openings for power steering because its electronic on the cobalts the brake fluid bottle is on the firewall in the engine compartment on the drivers side, the cap clearly says brake fluid, i don't know who was checking your car but all cobalts have electric steering. in order to fix the problem your going to have to have the brake system completely flushed with new brake fluid before any damage is done, hopefully no damage occured already!

Jul 04, 2009 | 2008 Chevrolet Cobalt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...