Question about 2006 Subaru Legacy

Open Question

2006 Legacy heater fan noise, need fan and resistor replacement. How do I remove the glove boxto get to fan?

How do I remove the glove box and other things to get to the fan and resistor? are the fans same part as others? 2006 Legacy regular sedan symmetrical all wheel drive.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 41 Answers

SOURCE: 93 Subaru Heater fan not working

Have you checked the earth? You may find current is going to earth via the fans. Find the earth for the heater and make sure it is earthing really well. Hope this helps.

Posted on Mar 23, 2009

pugwash814
  • 377 Answers

SOURCE: Replace heater blower motor on 1992 subaru legacy

yes that is correct, remove glovebox , metal bracket in front ( mark which way round this bracket goes it will go back wrong and glove box wont fit ) , unplug electrical plug from heater motor, unscrew 3 bolts/screws from motor replace in reverse..30 min tops..

Posted on Nov 15, 2009

wyno62
  • 364 Answers

SOURCE: heater in car will not work, 1990 Subaru Legacy

not sure if your controls are vacuum operated or cable, either way you need to remove the controls and inspect that hoses are not off or split, {do the **** test} and if cable is off that will be obvious what you need to do, Hope this helps, Good luck

Posted on Nov 20, 2009

  • 17 Answers

SOURCE: 2003 Forester Heater AC Fan Blower makes loud noises

it is electric, so oil wont help, call your local parts store they should have access to one in a day or two

Posted on Dec 13, 2009

  • 64 Answers

SOURCE: 1997 Subaru legacy cooling fan

well if the fan is stiff to turn by hand I would replace the fan the motor seems like is seized up, just in case ceck the fuses and relays, check the motors voltage and test the circuts voltage, make sure the ect sensor is working fine to be on the safe side. the easy way to make sure a relay is working is trade it with another for the same fuse box. if your fan cuts on you know you have a bad relay.

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the heater resistor?


Remove the glove box, you will see two connectors held in with screws with wires going to them. The lower connector is the resistor pack. Disconnect the connector, remove the screws and the resistor pack will slide out when pulled on. Then put the new resistor pack in making sure the orientation is correct, install the screws, reconnect the connector and install the glove box. Then you should be all set to go. I hope this info helps!

Aug 26, 2014 | 1991 Subaru Legacy

1 Answer

The heater only blows on full blast, the first three positions on the button does not work. the car is an 2006 Chevy Aveo LS hatchback


In the heater plenum behind the glove box you should find a 4 or 5 wire connector. That is called the heater resistor it has a series of different thickness springs and controls the Resistance to ground. That is what controls fan speed. First check the connector for melting if so you need to replace the connector and resistor if not remove the two screws holding the resistor in place and remove the resistor, you should find the springs are broken and replace the resistor. Note there are a couple of other things that can cause this problem but 99% of the time its this.

Mar 08, 2013 | Chevrolet Aveo Cars & Trucks

1 Answer

Heater fan resistor


Remove the Glove Box assembly. The heater fan and the heater fan resistor are behind the glove box. It is on my 90 4-cylinder Camry.

Oct 14, 2012 | 1990 Toyota Camry

1 Answer

How do I replace a ford focus 2005 fan speed control


see this and fix it. God bless you

Remove the passenger footwell lower trim panel underneath the glove box.

  • 2 Open the glove box and remove the screw holding the footwell air vent duct. Pull off the hose and remove the duct. Close the glove box.


  • 3 Disconnect the heater fan electrical connector. Remove the three bolts retaining the heater fan and remove the fan.
  • 4 Disconnect the heater fan resistor electrical connector, and remove the resistor.
  • 5 Install the new heater fan resistor by reversing the above steps.
  • Oct 04, 2012 | Ford Focus Cars & Trucks

    1 Answer

    How do you fix a fan sensor in a 2000 malibu


    are you talking about heating fan resistor! if so, this is where and how its replaced. it is behind glove box. remove glove box so you do not have to stand on your head, only about 7 or 8 screws. then loosen and slide ecm to one side. ( but when removing glove box, remove insulator panel under glove box first ) now you can see heater blower and resistor. it is beside the fan, remove the wires from it. take out holddown screws, then pull it out. have a good holiday!!

    Oct 08, 2010 | 2000 Chevrolet Malibu

    1 Answer

    2003 chev malibu blower fan not working in position #1,#2 ,#3.Works fine on #4,#5 Help please


    its the heater fan resistor thats causing it. it has coils for different fan speeds, if a coil burns out or breaks. then you will loose that fan speed. to replace resistor, remove glove box to give ya more room so you dont have to stand on your head!! remove insulating panel under glove box. loosen and slide ecm to the side. now you can see heater blower fan, resistor is beside it, just remove wires , take out the hold down screws. and thats it!

    Jul 26, 2010 | 2002 Ford Taurus

    1 Answer

    Blower motor for interior fan only blows on high speed. All the lower settings dont work now


    The blower resistor pack needs to be replaced, it's common for the blower speed resistors to burn up and will need to be replaced. It's easier to replace with the glove box out of the way. gmparts direct has the harness and resistor as a package deal. Their part number is PK15218254.

    GM Parts list:

    Resistor - p/n 15218254 $8.59*

    Connector - p/n 15306069 $30.70*

    Wiring harness - p/n 89019124 $20 *

    You don't need to remove the glove box, just lay on the floorboard and look up under the dash. There's a 4-wire harness plugged into the resistor assembly (white plastic), in the bottom of the black heater blower shroud. Unplug the harness, remove two small screws, and pull down to remove the resistor assembly.

    Good luck and merry xmass.

    Dec 15, 2009 | 2006 GMC Canyon

    1 Answer

    The heater in my 2000 chevy malibu is making funny noises ... speeds one and two dont work.. havent since we bought the car... for 2 years now.. but what is that sudden noise that came on yesterday... like...


    I have ran into the same problem, there may be something has got into fan cage. remove fan motor and investagate to see if it is blocked, or if fan is going bad. it is behind glove box, to remove. remove lower right dash insulator panel from under glove box. slide bcm aside for room to get at fan motor. remove 3 screws from fan motor, and remove fan after disconnecting wiring. the blower motor resistor is beside fan motor. the resistor will make ya lose 1 and 2 speeds. for it is a 5 step resistor.

    Oct 29, 2009 | 2000 Chevrolet Malibu

    2 Answers

    VW Jetta GL 2000, AC - Heater Fan stopped


    blower motor or resistor or the blower motor control switch.

    Jun 01, 2009 | 1998 Volkswagen Jetta

    2 Answers

    Ac blower motor


    it should be located in the heater/evap case under the dash by the glove box, usually the pigtail from the blower motor itself leads the the resistor pack.

    May 29, 2009 | 2006 Chevrolet HHR

    Not finding what you are looking for?
    2006 Subaru Legacy Logo

    Related Topics:

    29 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Subaru Experts

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7697 Answers

    Are you a Subaru Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...