Question about Cars & Trucks

Open Question

I need arobaggar orrientation. - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What parts will I need to to get to add cruise control on my 2004 extreme blazer


You need speed sensors, you need a complete wire diagram, you need a cruise control module, you need a different dash to indicate cruise control, you need lots of expertize.

Nov 09, 2015 | Cars & Trucks

1 Answer

Need to replace or reset airbags for 2004 cavalier


when a deployment occur . You need to change both air bag module, change SDM (supplemental deployment module)
need to change the SIR coil Inside column steering and the front discriminating sensor.
Befor installing you need to remove the SIR fuse or disconnect battery
no reset needed

hope it help

Oct 15, 2014 | 2004 Chevrolet Cavalier

1 Answer

Need instructions to replace ac comp clutch bearing on 2000 buick la sabor 3800 engine


Yes you need special tools.You need to remove the compressor clutch and the bearing.Then you need to press the bearing off the clutch and when installing you need to set the air gap.If you are not familiar whit this repair you should take it to a repair shop.Sometimes it can be done in the car without recovering the freon and sometimes not.Depending on how much clearance there is.Hope this helps.Good luck.

Nov 13, 2011 | 2000 Buick LeSabre

1 Answer

Our 2004 yukon has become Hard Starting. I took it to the dealer and they said it was the Fuel pump. Sometimes it starts on the first turn of the key and the next time we will have to try starting twice. I...


First you have to make sure there is little to no fuel in tank. Drive vehicle untill it is almost empty. Then disconnect fuel pump relay and fuse. Try to start vehicle to relieve fuel pressure. If you do not have a hoist elevate the vehicle on 4 jack stands. Disconnect the fuel line and return line nearest tank. Disconnect filler hose fron tank. Place 18" x18" piece of plywood on hydraulic jack and place under and against middle of tank. Disconnect straps holding tank in place. Lower tank slowly untill you can disconnect electrical connectors. Remove tank and change pump. There is a ring holding sending unit and pump on tank. this ring can be moved with a mallet. Make sure to clean off all debris from top of tank before removing sending unit. Remove sending unit carefuly and remember where float is orriented in tank.

Aug 20, 2010 | GMC Yukon XL Cars & Trucks

1 Answer

Water on the number to sparkplug , do i need any special tool for the head job


WHEN WORKING OR DOING ANY KIND ENGINE WORK YOU NEED ALL STANDARD AND METRIC WRENCH SET 1/4 3/8 1/2.YOU NEED A CRAFTMANS TOOL SET IT HAS ALL THE SOCKETS YOU WILL NEED.YOU NEED A TORQUE WRENCH METRIC OPEN BOX END WRENCHES. AND YOU NEED A HAYNES REPAIR MANUAL.

Jan 09, 2010 | 2002 Isuzu Rodeo

2 Answers

Dash board doesn't light up


remove dash to the bulb components (the layer of dash with only bulbs[looks complicated]) turn dash lights on and identify wich bulbs are not working, replace them with the correct bulbs. if this is unsuccesfull find the connection from the bulbs to the wire and also the connection from the wire to switch. ensure the components inside the connextions are clean(pull apart and check for rust, dust, dirt ect..) you can buy connection cleaner from most car orrientated shops.

Nov 24, 2009 | 1991 Nissan Pickup

1 Answer

Need to change a starter. Need a diagram to show


Go to autozone.com register for free , then you will have full free online repair manual with everything you could need

Aug 05, 2009 | 2005 Chevrolet Equinox

1 Answer

How to change the spark plugs


if its your first time you need a haynes repair manual.you need a spark plug boot puller.you need 3/8 ratchet wrench.spark plug sockets.from size 5/8 to 13/16.you probably need size 5/8 socket.you need extensions different sizes.and universal joints.to reach hard to get plugs.you need torque wrench. and spark plug gap set.

Jul 07, 2009 | 2002 Kia Sportage

2 Answers

Head replacement


You can do it. You will need a good set of basic hand tools. The only special tool you should need is a torque wrench. If you have never done this, I suggest buying a manual

Jul 04, 2009 | 2002 Buick Rendezvous

2 Answers

Need to know what is done in a 100,000 mile service


normal tune up
chasis lubricationtie
tie rod lubrication
trasmission service
if 4X4 transfer case fluid needs change
differential fluid needs change "both if 4X4"
brakes need service if they havent recently
coolant is probably bad too
how is the battery?
check serpentine belt

these are just a couple......"there could be a couple that dont need service but this is what i would do".

hope this helps XD

May 13, 2009 | 2002 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...