Question about 1998 Jeep Grand Cherokee

1 Answer

Where is the crank sensor located

It has the 4.0 straight six engine?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

It is on top of the transmission on the drivers side . you can see it from under the jeep

Posted on Dec 31, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford freestar 2004 where is the O2 sensor #1 located


There is 4 senors the bank 1 sensor 1 is located in front of the LH (Drivers side) catalytic converter
Hope this helps

Jun 22, 2014 | 2004 Ford Freestar

1 Answer

Where crankshaft position sensor located on 2000 Jaguar vanden plas?


if its a v8 its on the underside on the flywheel/torqueconverter housing in the centre 8mm bolt or torx head close to the subrame crossmember if its a x300 straight six its on the top front above crank pulley 8mm bolt.

Jan 01, 2014 | 2000 Jaguar Vanden Plas

1 Answer

P320


What engine?

P0320 and P1391 are crank sensor codes. The symptoms you have certainly point towards one possibly going bad.

if this is a 4.0 straight six you can find the crank sensor on the drivers side of the transmission where it blots up to the engine on the top side. If you look in between the intake and the firewall you should be able to locate the harness and follow it to the sensor. The sensors are relatively inexpensive and would be an excellent start.

Feb 16, 2012 | 1997 Jeep Cherokee Country

2 Answers

1996 Jeep GC Laredo, Drove it home, parked it in the back yard, un-hooked a little trailer, went to start it back up and all it does it crank. No Fire. I pulled a plug and no sparks. Can't...


On the straight six engine they have a crank shaft sender located on front of transmission it reads the flywheel turning. When they go bad it will not fire and can quit like yours did.

Jun 26, 2011 | 1996 Jeep Grand Cherokee

1 Answer

My BMW 520i starts up when cold but when it's warmed up and I turn engine off it won't start it's a 1997 straight six tiptronic whats causing this?


If the engine cranks but fails to fire, the car may be flooding due to a failed temperature sensor. There are several, but the most likely problem would be the water temperature sensor.
If the engine fails to crank when hot, the starter motor is failing and will need to be replaced.

Jun 23, 2011 | BMW 525 Cars & Trucks

2 Answers

How do you replace the crankshaft positioning sensor?


well you did not list the engine . so here is all of them on the 2.0 or 2.4- 4 cyl the crank sensor is located behind the generator just abouve the oil filter mounted to the eng block. on the 2.5 V6-remove the speed control servo from the drivers side strut tower. (its located just under the distributer) remove the retaining bolt and pull the sensor straight up out of the transaxle housing

Jan 27, 2011 | 1998 Chrysler Cirrus

1 Answer

My check engine light is on and I've been told it is the cam sensor, but I can't find one. It's a 2005 nissan altima. Do they have a cam sensor and a crank sensor?


This engine has both. Nissan recommends replacing them at the same time, I think your local Nissan dealer will tell you the same thing.The cam and crank sensors are in the rear of the engine.Looking from the drivers fender find the right rear corner of the valve cover and look straight down the back of the head. the cam sensor is 3-4 inches down from the valve cover gasket surface.the crank sensor is basically straight down from the cam sensor but much harder to see. it is just above the oil pan gasket surface...

Mar 29, 2010 | 2005 Nissan Altima

2 Answers

Where does a crank sensor sit on a 1996 lincoln continential


It is located down by crankshaft. If you follow the spark plug wires down to the coilpack & module. Then from module straight to crank sensor

Nov 12, 2009 | 2007 Lincoln Continental

1 Answer

2004 suzuki verona..where is bank 1 senor 1 located on the engine


This car has a transversely mounted straight six I believe, which is really unusual, but that means it only has one bank, so "bank 1, sensor 1" will be the upstream O2 sensor (between the engine and the cat) and "bank1, sensor 2" will be the downstream sensor (behind the cat).

May 10, 2009 | 2004 Suzuki Verona

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...