Question about 2008 Opel Corsa 1.2

Open Question

Change headlamp bulb on Corsa 1.2 sri 58 plate

Posted by on

  • Peter Butterworth Dec 31, 2012

    Cannot get my fingers in to unclip bulb on nearside dipped headlamp bulb cannot even see it let alone unclip it

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why am I only getting 5.5volts at the passenger side break light on my 2008 Vauxhall corsa 1.6 sri


most likely that a ground connection is missing or something along those lines.
does it read 5.5 with the bulb installed?
try grounding it directly to the chassis or batterie.

Feb 21, 2015 | Vauxhall Cars & Trucks

1 Answer

Corsa Faults


Check what's called blower motor resistor.usually burns out and only does the one speed.

Oct 31, 2013 | Cars & Trucks

1 Answer

Jst put new cambelt on 54 plate corsa 1.8 16v sri now not starting getting code 0340 camshaft sensor can anyone help


Recheck the timing as possible it's 1 tooth out and this will give false reading from sensor if all is ok timing wise sensor at fault damaged, stressed wiring to sensor

Aug 07, 2013 | Vauxhall Cars & Trucks

1 Answer

How to change the headlight bulb on 2009 gmc sierra driver side


1. Loosen only, do not remove, the lower outside hidden headlamp bolt (2). 2. Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support. 3. Pull the lamp assembly slightly forward to access the electrical connection. 4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
Headlamp Screws (Qty: 2)
1 Caution: Refer to Fastener Caution .
6 Nm (53 lb in)
O Headlamp Screw (Hidden)
6 Nm (53 lb in)
3 Headlamp Housing Support


Preliminary Procedure Remove Healamp
Remove either the LF or RF headlamp assembly. Refer to Headlamp Replacement (Chevrolet) Headlamp Replacement (GMC HD)
Headlamp Replacement (HD Diesel).
Headlamp Bulb (Hi)
Warning: Refer to Haiogen Bulb Warning .
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.
Headlamp Bulb (Lo)
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.

Need more come to https://www.autorepairhelp.us


change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-0.png change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-1.png

Aug 14, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

2 Answers

I have a 2004 Vauxhall Corsa C 1.4 SRi with Dull Headlights.


i have the same problem with my 54 plate corsa c i think its because the got the projector headlamps in and there is dust on the lens inside the headlamp,

i hav also tried puttin extra bright bulbs n and it makes it worse i cant see a thing

best bulbs i have found is genuine vauxhall or saab gm h7 bulbs
there normally about £8

regards johnyburrells mitsubishi and saab

Jan 19, 2010 | 2000 Acura Integra

1 Answer

How do I get to the drivers side light bulb in a 2006 Chrysler Sebring Sedan? I have the replacement bulb and want to change it myself.


I will assume you are talking about the headlight?!

Removal
CAUTION: do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced life will result.

1) Disconnect and isolate negative battery cable.
2) Remove headlamp unit retaining screws. (bolts)
3) Remove headlamp unit to expose back of unit.
4) Disconnect wire connector from back of headlamp bulb.
5) Rotate retaining ring counterclockwise.
6) Remove retaining ring.
7) Pull headlamp bulb and remove from headlamp unit.

Installation

1) Install headlamp bulb to the headlamp unit.
2) Install headlamp bulb retaining ring.
3) Rotate retaining ring clockwise.
4) Connect wire connector to bulb.
5) Install headlamp unit.
6) Install headlamp retaining screws. (bolts)
7) Connect the battery negative cable.

More detailed info on how to get unit out.

Removal

1) Disconnect and isolate the battery negative cable.
2) Remove the two retaining screws.
3) Remove the upper fascia retainers by prying under the head of the fasteners with a flat bladed tool.
4) Remove headlamp unit from fender side first, then pull headlamp unit out.
5) Disconnect the wiring harness from the bulbs.
6) Remove the headlamp unit.

Installation

1) Connect wire harness to the bulbs.
2) Install headlamp unit.
3) Install the retaining screws.
4) Install upper fascia retainers.
5) Connect the battery negative cable.

I hope this will help you to get the light changed.

Jan 11, 2010 | 2006 Chrysler Sebring

1 Answer

Replacing headlight bulbs Altima2003


Removal and Installation To Remove:
  1. Ensure that lighting switch is in the OFF position.
  2. Disconnect negative battery cable.
  3. Remove or disconnect the following:
    • Front fascia
    • Headlamp mounting bolts
    • Headlamp by sliding it forward
    • Headlamp connectors
To Install:
  1. Install or connect the following:
    • Headlamp connectors
    • Headlamp and mounting bolts
      1. Torque to: 58 in. lbs. (6.5 Nm)
    • Front fascia
    • Negative battery cable
71c495d.gif

Oct 01, 2009 | 2003 Nissan Altima

1 Answer

Getting an error code of p0400 on a vauxhall 1.7 diesel sri corsa 54 plate, how can i fix it??


PO 4OO Code is an EGR valve flow malfunction. It might be as simple as removing the valve and cleaning it.
Hope this is of some help to you
John

Sep 06, 2009 | 2009 Volkswagen Routan

2 Answers

How to change headlight bulb on ford mondeo


Very easy, 2 or 3 minutes.
Remove radiator grille. 2 plastic fittings on top, quarter turn and lift out grille.
Remove complete headlight. Simply lift out 2 L shape retaining pins. Disconnect lead. Ease out complete headlamp unit.
Remove back of headlamp unit to access bulbs. Disconnect lead from bulb while bulb still held by clip. Then release clip to remove bulb.
Reverse process to fit.

Jan 02, 2009 | 2001 Ford Focus

Not finding what you are looking for?
2008 Opel Corsa 1.2 Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Opel Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Brad Brown

Level 3 Expert

15937 Answers

george parkes

Level 3 Expert

975 Answers

Are you an Opel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...