Question about 2001 Opel Astra

1 Answer

P0340 - Camshaft Position Sensor A Circuit (Bank 1)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Opel Master
  • 22,114 Answers

The usual opel fault ,its the computer misreading the crank sensor owing to build up of magnetic flux in the crankshaft .Now what you do here is simple and if you dont it will cost an arm and a leg to repair.Now look on the front pulley and see if you have the earlier pulley still fitted as old stock on the assembly line ,Now look and see if it has a toothed ring and a support bracket top left hand side,now if it has the obtain a sensor for the earlier model and fit it to the front support ,now the two wires that go to the original crank sensor at the back right hand side of the engine disconnect the multiplug and then snip it off ,extend the two wires to accomodate the sensor you have fitted to the front pulley and try start it and if its still the same reverse the wires ,this will cure it i promise ,now for computer thats bolted to the inlet manifold right side then disconnect the mountings and move it away from the engine as far as the loom allows then tie it up with a couple of plastic ties so its away from the engine ,now mount a old computer fan to the casing of the module and wire it in to the ignition circuit via the fuse box ,leave that sill engine cover off the engine as well as this causes no end of problems here in spain with the heat build up and no air flow when driving.This will cure your problem i promise as i do about at least one a month of this type of engine like the astra and the 7 seater whatevers its called ,iam old and my memory ? .Now dont forget the polarity on the engine crank sensor if after fitting the new one and its still the same reverse the wires .

Posted on Dec 31, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine codes p0340


P0340 Dodge - Camshaft Position Sensor Circuit Bank 1 Sensor 1 P0340 Dodge Camshaft Position Sensor Circuit Bank 1 Sensor 1

Aug 19, 2014 | 2000 Dodge Durango

1 Answer

I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335 Crankshaft Position Sensor -Circuit Malfunction
P0336 Crankshaft Position Sensor -Range/Performance
P0337 Crankshaft Position Sensor -Low Input
P0338 Crankshaft Position Sensor -High Input
P0339 Crankshaft Position Sensor -Intermittent
P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

Aug 07, 2014 | 2000 Nissan Quest

1 Answer

What is lexus es300 fault code p0340


It is the camshaft position sensor A bank 1 code.
Here are possible causes:
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Jul 14, 2014 | 1996 Lexus ES 300

1 Answer

P0016 what is that n how u fix it


P0016 Crankshaft Position - Camshaft Position Correlation
P0135 O2 Sensor Heater Circuit
P0138 O2 Sensor Circuit High Voltage
P0340 Camshaft Position Sensor "A" Circuit
P0344 Camshaft Position Sensor "A" Circuit Intermittent
P0508 Idle Air Control System Circuit Low
P0522 Engine Oil Pressure Sensor/Switch Low Voltage
_____________--
JMA TRS-5000 Cloning Machine

Jun 03, 2013 | Cars & Trucks

1 Answer

Mustang error codes P0340 , P0344


These are camshaft position sensor codes. Replace camshaft sensor.

Apr 18, 2017 | 2006 Ford Mustang GT

1 Answer

P0340 99 jeep cherokee code


P0340 JEEP - Camshaft Position Sensor Circuit engine cylinder Bank 1 Sensor 1

Possible causes- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sometimes and in some models, low battery voltage or a weak starter can can trigger a Camshaft Position Sensor code.

Read more: http://engine-codes.com/p0340_jeep.html#ixzz25iQflrEb

Sep 06, 2012 | 1999 Jeep Grand Cherokee

3 Answers

I have a Chevy 2006 Aveo. Two codes came up when the engine check light was put on a scanner. Code P0340 and Code P0133. The check engine light has turned off and on by itself several times in the...


P0340 OBD-II Trouble Code - Camshaft Position Sensor Circuit Malfunction

This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms can include:
* Hard starting or no start
* Rough running / misfiring
* Loss of engine power

Causes: A code P0340 could mean one or more of the following has happened:
* a wire or connector in the circuit could be grounded/shorted/broken
* the camshaft position sensor may have failed
* the PCM may have failed
* there exists an open circuit
* the crankshaft position sensor may have failed

Possible Solutions: With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Visually inspect all the wiring and connectors in the circuit
* Check for continuity in the circuit wiring
* Check the operation (voltage) of the camshaft position sensor
* Replace the camshaft position sensor as required
* Check the crankshaft position circuit as well
* Replace circuit wiring and/or connectors as required
* Diagnose/replace the PCM as required



P0133 OBD-II Trouble Code - Oxygen Sensor Circuit Slow Response (Bank1, Sensor1)

This involves the front oxygen sensor on Bank 1. This code indicates the engine air fuel ratio is not being adjusted by the oxygen sensor signal or the ECM as expected to do so, or not adjusted as often as expected to do so once the engine is warmed or under normal engine use.

Symptoms: You will likely not notice any drivability problems, although there may be symptoms.

Causes: A code P0133 may mean that one or more of the following has happened:
* The oxygen sensor is faulty
* The wiring to the sensor is broken / frayed
* There is an exhaust leak

Possible Solutions: The simplest thing to do is to reset the code and see if it comes back.
If the code comes back, the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
* Check and fix any exhaust leaks
* Check for wiring problems (shorted, frayed wires)
* Check the frequency and amplitude of the oxygen sensor (advanced)
* Check for a deteriorating / contaminated oxygen sensor, replace if necessary
* Check for inlet air leaks
* Check the MAF sensor for proper operation


Hope this helps (remember to rate this answer).

Feb 09, 2011 | 1999 Chevrolet K1500

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

3 Answers

Reccieved P0141, P0147, P0340 as emission diagnostic trouble codes. What do these mean?


P0141....O2 Sensor Heater Circuit (Bank 1 Sensor 2)

P0142....O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)

P0143....O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)

P0144....O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)

P0145....O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)

P0146....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)

P0147....O2 Sensor Heater Circuit (Bank 1 Sensor 3)

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

Sep 20, 2010 | 1997 GMC Sierra

2 Answers

How to fix po134 sensor


O2 Sensor Circuit No Activity Detected Bank 1 Sensor 1

the bank one sensor is either disconnected are faulty.

the bank one sensor is the sensor in the exhaust of the rear cylinder bank of the engine cylinders 1,2,3, the sensor is the one before the catalytic converter. U will need an O2 semnsor socket to remove it or in some cases a 7/8" open end wrench will do.

Oct 23, 2009 | 1996 Plymouth Grand Voyager

Not finding what you are looking for?
2001 Opel Astra Logo

1,059 people viewed this question

Ask a Question

Usually answered in minutes!

Top Opel Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Brad Brown

Level 3 Expert

15557 Answers

george parkes

Level 3 Expert

975 Answers

Are you an Opel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...