Question about 1995 GMC Sierra C1500

1 Answer

Clutch adjustment on 1995 gmc 1500

Clutch squeels has no play in petal at all. have a new clutch and throw out.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • GMC Master
  • 22,326 Answers

Sorry iam a europeon mechanic with no knowledge of this model but if i knew if it was hydraulic or a manual clutch then this would give me a better idea but if no play then its over adjusted causing the clutch to ride a bit hence the noise but how the adjuster works i have no idea here

Posted on Dec 31, 2012


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 484 Answers

SOURCE: need to know how to disconnect clutch master cyl

You do not have to. The pedal operates a ram that pushes the piston in the master cylinder.

Posted on Oct 26, 2009

  • 56 Answers

SOURCE: my 1986 gmc has a

Make sure all the air is out of the lines ,,bleed the system to do this

Posted on Aug 22, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Not able to select gears when engine is running,but when off selects easy,after fitting a new kit still does the same

The clutch is not releasing , several things can be the cause, check the following , Throw out bearing same size,clutch driven plate not fitted back to front, clutch fork is fitted to throw out bearing housing and pivot mounting, is the slave cylinder rod the same length, has the clutch free play been adjusted, has all air been bled from the master cylinder, If cable operated has free play been adjusted. Has the new pressure plate the same throw as the old one.

Jul 02, 2016 | Cars & Trucks

1 Answer

Www youtube com activate

If it is a cable clutch operation the adjustment should be at the clutch throw out arm . If it is hydraulic the replace the clutch master cylinder as you may have a blocked compensating port in the cylinder which keeps pressure on the clutch arm and will slip the clutch

Dec 19, 2013 | 1997 Volkswagen Golf

2 Answers

Noise in the bell housing

the clapper is loose (joking)
ok is it a m/t or A/t?

Oct 23, 2013 | 1995 Ford Aspire

1 Answer

Need to know how to disconnect clutch master cyl from clutch petal on 2003 gmc 1500 4.3l manual shift

You do not have to. The pedal operates a ram that pushes the piston in the master cylinder.

Oct 25, 2009 | 2003 GMC Sierra

2 Answers

1995 ford ranger with new cluch and slave. still has pedle play for the first half of the pedle throw


Oct 23, 2009 | 1995 Ford Ranger Supercab

1 Answer

New master and slave still have no petal pressure or clutch

Was the slave cylinder bled correctly? If that's all set then that would leave the throw-out bearing and/or clutch assembly.

May 31, 2009 | 1991 Nissan Pickup

1 Answer

Hydraulic P20 tranny with hasport hydraulic > cable conversion. The arm that attaches to the TOB arm came out and the clutch stopped working. When i popped the hood and looked i found the bolt that...

The throw out bearing arm was on the outside of the clutch actuator arm. The throw out bearing arm should go into the clutch actuator arm with a bolt going into the clutch actuator arm through the throw out bearing arm. I used some blue locktite to make sure the bolt didn't come out again. See pic below.

May 04, 2009 | 1991 Honda CRX

1 Answer

We have a 1985 GMC 2500 pickup - we can not get the clutch to engage. What could be the problems?

Clutch could just need adjustment, or throw out bearing replacement or clutch replacement if no adjustment is left. consider the age and mileage if clutch has never been changed, would recomend it rather than throwing parts at it.

Jan 09, 2009 | GMC K2500 Cars & Trucks

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides