Question about 2009 Ford F-150

Open Question

2009 F150 wrench light flashing truck going into limp mode vehichle jerking will flashing

Single cab 4.6 engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 52 Answers

SOURCE: 2000 Ford F650 w cummins 5.9 TD

Check your lift pump, if bad the injection pump will run w/o lubrication. Pump will be restricted to using fuel to the engine. It will self destruct. Best advice is to get to a dealer and find it before some thing bad happens. Good luck!!

Posted on Aug 29, 2009

Ad
  • 328 Answers

SOURCE: Service Engine Soon Light

no the coolant wouldn't cause the light to come on,and yes if you don't have the know how to buy and attach an obdii code reader to your truck then you will have to take it to a garage to be sure what the problem is........however the check engine light is a warning that something is experiencing a problem but correction of the problem doesn't have to be immediate, if you can't afford it or don't have the time to have it looked at right away.(keep in mind that with the light on your computer is in limp mode and you will see a drop in fuel mileage)But to get the light to go out you need to either disconnect the battery for 5-10 min or have someone check and reset the light.if you do the battery disconnect to reset it the light may not come back on for some time or may come on right away.last winter i had the light come on for an o2 sensor heater.........i reset the code and never saw it again. so if you can try the battery disconnect reset first if the light comes back on then take it to a garage.
hope this helps!

Posted on Dec 30, 2008

  • 56 Answers

SOURCE: f150 broke shift tube

Look under the car the linkage on the trans may have come off.

Posted on Jul 21, 2009

  • 1986 Answers

SOURCE: where is the switch for the bed lights on a f150

It should be on the same switch as your dash dimmer switch. Turn the dial on the dash light to make them as bright as they'll go, then there should be a little resistance and if you keep turning, it should turn on your bed lights on...

Posted on Oct 13, 2009

  • 1 Answer

SOURCE: throttle does not work-wrench light on

I need to know if the TPS in my 2006 Ford Fusion SEL, can be replaced on my own, or does it need to go to a dealer to be replaced?

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset the computer and get it out of limp mode on a 2002 Ford F150 Step by step instructions how to reset limp in mode on my 4-2 Ford F-150 2002


You have to find what is causing it to be in limp mode ! Have the vehicle checked for DTC's - diagnostic trouble codes . Do diagnostic's , fix what the problem is , sensor , wiring , a control module , then the light will go out .

Jan 02, 2017 | Ford Cars & Trucks

1 Answer

2009 pontiac wave doesn't upshift.


Check engine light on ? Or any other lights , wrench symbol light ? Your best bet would be to have a scan tool hooked up , check for DTC'S - diagnostic trouble code's in all the control modules on the vehicle . A factory or professional scan tool , not a code reader .

Dec 31, 2016 | Pontiac Cars & Trucks

1 Answer

I have a 2009 malibu I am getting a code p0304 cylinder misfire. What is the most common problem with these cars with this code ?


number 4 misfire check either plug or coil --as to jerking if vehicle is not running correct [misfire ]it will not drive smooth trac light --it can be related to the misfire or check abs and brakes and power braking will set off traction control and puts a strain on brakes and c/v axles

Aug 02, 2016 | 2009 Chevrolet Malibu

1 Answer

Engine light comes on and engine jerks


do the preliminary checks first ---oil /water levels and engine temperature . Run fault codes to find what sensor put the engine /transmission in limp mode to protect the units.

Feb 16, 2014 | 2006 Dodge Stratus

1 Answer

Ford f150 overdrive light flashes


This usually means there is a transmission related fault. There is probably a error code stored, and your transmission may be in limp mode; usually 2nd gear only. I don't know if Autozone can read trans codes. This may be a dealer only repair. Have you checked your transmission fluid?

Dec 19, 2009 | 1999 Ford F150 Regular Cab

1 Answer

Saturn V6 2000 model with jerking. I can drive about 4 blocks and then the light pops on and says reduced power and I can go no more than 20 miles per hour if I am going a good speed. The steering wheel...


It is going into limp mode. There is a serious problem somewhere. Could be with the engine or transmission. You need to have the ECU scanned to see why it is going into Limp Mode. I suggest you seek professional help.

Oct 10, 2009 | 2000 Saturn SL

2 Answers

1997 Ford Mustang over drive light flashing while driving


the light is flashing to alert you to the fact that the transmission sensors have detected excessive slipping, u may not feel this but it is the case.

Aug 06, 2009 | 2002 Ford F150 Regular Cab

1 Answer

Limp home mode


You need to scan for engine trouble codes. Most parts stores will do this for free, and tell you what they mean and make recommendations on what to do. The 'limp mode' kicks in to prevent damage to the vehicle when the computer gets data that something is wrong.. When you shut it off, it's temporarily reset, but then the cars computer is signaling there is still a problem, and it goes back into limp mode. If you have any questions after getting the codes 'read' , post questions and code #;s here for help. Good luck.

Apr 28, 2009 | 2004 Ford F150

1 Answer

'03 GMC 2500HD 4x4 problems


Take your positive cable off battery and wait a few minutes..This resets the computer and takes it out of limp mode.Theres been a lot of problems in the dash so if you can find an auto zone and have them scan it They'll do it for free.But as far as the lights my truck does the same thing. Just flick your fingers on the buttons and they should flash..The plug in the back of buttons was loose..

Dec 17, 2008 | 2003 GMC Sierra 2500HD

Not finding what you are looking for?
2009 Ford F-150 Logo

Related Topics:

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...