Question about 1997 Mercury Mountaineer

1 Answer

How do i get the front head light lense off

I am trying to change the bulb but can not get the from head Light off.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 46 Answers

Open the hood and look at the back of the light all you change is the bulb... you push in on the bulb and twist take it out and then take to the auto part store and they will give you the right one.. PS most auto part stores will take your old one out for you and put new one in

Posted on Jan 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drivers side head light is way dimmer than passenager light even after new bulb replacement


When looking from the outside of the headlight at the bulb, can you see the bulb clearly??
These lenses are notorious for dulling very badly. If it has you can use a regular headlight 'restoring' kit sold at most auto part locations.

If it is not a lens issue, you may have a wiring/supply issue.
Then you would need to find the troublesome wire/connection.
I am not the best at wiring issues, but I would try to find a power source wire with the same amperage rating, run a bypass jumper from a known good voltage source and see if the light changes. If no change, your problem may be the harness or plug at the rear of the headlight bulb.
Hope I could help
GL

Dec 31, 2011 | 1999 Plymouth Voyager

1 Answer

How to change back brake light bulb n/s


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

Apr 30, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

How to replace front light low beam blub?


Hello i can assist you open your hood behind the head lamp lenses is a head lamp bulb socket twist it counter clock wise then remove the socket and bulb unplug your old bulb replace with your new bulb and replace the socket back and clock wise tighten.Now turn your head lights on check both high beam and low.

Dec 28, 2010 | 2005 Dodge Dakota

1 Answer

Changing the headlight on a 2006 pontiac g6


To replace the headlight bulbs.You need to remove the head light assembly out.The head light assembly is held by 2 to 3 three screws on each side. You need to remove those screws first.The front trim will get loose,the front trim is held by pins.The pins are of plastic and easy to release.Just release this pins and the front trim will get completely loose and can be easily taken off/. The head light assembly is in the front fender.Once the front trim is removed the head light assembly can be easily removed from front fender compartment.If its bit tight there,then you can use a screwdriver to give it a pull towards out.The head light bulbs can now be easily seen as well as easily removed now.Turn the bulb socket counterclockwise to remove the bulb from the bulb assembly. -------- Keep updated for any more queries.Thanks.

Oct 14, 2010 | 2006 Pontiac G6

1 Answer

Right rear turn signal and brake light not working, but running light does, changed bulbs still not working - fuse is ok, Front tuen flshes rapid like burnt out bulb? short somewhere, live in the dessert...


Do you have a test light? On the plug to the right rear light, check for power on the dark green wire with someone holding the brake. If it lights up replace the circuit board the bulbs are pushed into. The parts stores stock these. If you don't have a test light, try switching the rear lenses side to side and see if the problem switches sides.

May 16, 2010 | 1997 Chevrolet Tahoe

1 Answer

How do i change the brake light on jeep liberty 2006?


1) You will need to open the rear swing door.

2) On the inside jam there are two torx headed screws (T-15's if I remember correctly).

3) Unscrew the two torx screws.

4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet).

5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick).

6) The light bulbs are twist mount settings inside the light casing.

7) Twist out the mount setting, change the bulbs, and reset the light mountings.

8) To put the light casing push the light casing back on and put in the screws. Everything else will work in reverse when it comes to assembling the whole unit.

2006 Jeep Liberty Replacement Light Bulb Sizes
Low Beam Headlamp Bulb Size: 9007
High Beam Headlamp Bulb Size: 9007
Parking Light Bulb Size: 2825 or 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3757ALL
Tail Light Bulb Size: 3157
Stop Light Bulb Size: 3157
High Mount Stop Light Bulb Size: 921
Fog/Driving Light Bulb Size: 9145 or H3-55W
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3157
Front Side Marker Light Bulb Size: 168
Ash Tray Light Bulb Size: 161
Map Light Bulb Size: 578
Dome Light Bulb Size: 578
Step/Courtesy Light Bulb Size: 906
Trunk/Cargo Area Light Bulb Size: 578

Thank you for using fixya, and good luck

May 08, 2010 | 2006 Jeep Liberty

1 Answer

Change the running light on a 2008 Tahoe


remove the clips that hold the head lights then you can remove the lenses for the DRL and remove the bulbs.

Aug 02, 2009 | 2000 Chevrolet Tahoe

4 Answers

Front signal light not working and rear signal lights flashing fast on 1999 intrigue


Your front turn signal socket is shot. Buy a new one at the dealer for about 30.00. It will fix it. You may be able to clean it and wiggle it to get it to work. But it wont last very long. I had the same problem. Replaced the socket and it is fine. Note: If one side is bad the other side it not far behind. Probably 2 or 3 months it will go also. Good Luck.
Bill

Apr 17, 2009 | 1999 Oldsmobile Intrigue

1 Answer

Front turn signal


the light assembly has to come out. there are two bolts 10mm. heads on top but after you take the bolts out pull light forward the bottom plastic on your bumper will get in the way carefully!! push down the plastic this will not be fun because the tollerance is to close.but with the lense in your hand you will get right to it.

Jan 25, 2009 | 2004 Chrysler Sebring

1 Answer

Change ford festiva front light bulb


Hello, the front light bulbs are easily changed by twisting the plastic holder in the back of the lamp that holds the bulb counter-clockwise. You turn it about a 1/4 turn and then it pulls out and you can switch bulbs. Do not touch the new bulb with your fingers because oil from your fingers will cause the bulb to burn out quickly.

Oct 20, 2008 | 1993 Ford Festiva

Not finding what you are looking for?
1997 Mercury Mountaineer Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...