Question about Mitsubishi Cars & Trucks

1 Answer

How do i remove the entire iognition switch assemble in mitusbishi gallant 1991

I need to replace the whole ignition switch and holding bracket assembly

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 2,122 Answers

Hi Bruntwood, Disconnect the battery, and then unscrew the screws fitted underneath which hold the plastic cowling surrounding the steering column and then remove the two halves. Disconnect the electrical socket from the plug and then identify the four blind bolts holding the saddle of the ignition barrel and switch. There are a few ways of removing those bolts, but the easiest is to tap them out with the correct sized cold chisel. Once removed the ignition barrel and switch can then be removed and replaced. Assembly is the reverse procedure. Regards and have a happy new ignition barrel and switch and new year. John

Posted on Dec 31, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Rebgagnon
  • 382 Answers

SOURCE: Need to replace a headlight assembly for a 2006 Subaru Outback.

No, you just remove the radiator grill and the side marker light and the headlight housing bolts and it comes out. Not a real hard job and is Real straight forward. Good luck and have a good day.

Posted on Mar 29, 2009

  • 1 Answer

SOURCE: Ignition switch removal

get a proper steering wheel puller, pull the steering wheel off. remove the screw for the hazard switch. remove 1 screw and a metal bracket for the signal switch. remove 3 screws holding the white switch in top of column. Then you need to pull this switch up out of the way, but in order to do this without wrecking it, you need to remove the plastic panels underneith the column to get at the column mounting bolts. there should be 2 13mm nuts holding the column to the dash. remove these. then there should be 4 13mm bolts holding the bracket to the column. remove these and there should be a plastic casing that th wires go through. remove this and unplug the wiring. now you can push the wiring up and out of the way without wrecking your signal switch. now remove 1 philips head screw holding the ignition switch in place and pry it out gently with a flat screwdriver.

installation is reverse procedure of removal

Posted on May 18, 2009

Molson02536
  • 3854 Answers

SOURCE: need to replace Mirror Assembly, 03 suburban

Your going to have to remove the inside door panel to get to the three bolts that hold the out side mirror assembly. Once you have the door panel off you'll see the three bolts that hold the mirror assembly, just un-bolt and un-clip the wire harness to the electric/heated mirror. To install the new mirror assembly, just do everything in reveres. Go to Auto Zone and by extra door panel clips, there is a good chance of breaking some of the retainer clips and Auto Zone will have the step by step instructions to replacing the mirror assembly and the removal to the door panel. Good luck and keep me posted. Be glad to help.

Posted on Jun 22, 2009

  • 1071 Answers

SOURCE: how to remove a 96 Volvo 960 wagon tail light assembly

there are 4 ten millimetr nuts holdin assemly to car remove trim to see them

Posted on Jul 21, 2009

  • 1 Answer

SOURCE: i need to replace front headlamp lens peugeot 405 1992

phone the scrapyard you bought it from, they had to take it out and having had your business, will hopefully be helpful!

Posted on Feb 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to remove ignition cylinder. I have pressed release button on the back, but the cylinder will only come halfway out.


TO REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Key System)
(a) T urn the ignition switch lock cylinder assembly to the
ACC position.
(b) Insert a screwdriver into the hole of the steering column upper with switch bracket assembly. Pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper with switch bracket assembly.
(c ) Insert a screwdriver into the hole of the steering column
upper with switch bracket assembly. Tilt the screwdriver
to disengage the claw of the ignition switch lock cylinder assembly, and pull out the ignition switch lock cylinder assembly.



25656969-ts5vql1j3jwqenesgxdwpnsg-5-0.png Thank you for visiting Fixya.

Apr 20, 2015 | 2010 Toyota Corolla

1 Answer

Replace ignotion switch on 95 geo trackker


1.Remove steering wheel cover from screws in bottom
2. pop off horn cover should snap off
3. Unplug three plugs to switch assembly
4. Remove steering wheel nut pull steering wheel may need puller
5. unbolt switch assembly from ignition bracket about three bolts
6. remove switch assembly and lay to side
7. mark ignition bracket vertically and horizontally
9. remove two tamper proof bolts with chizel
10. unplug ignition switch and remove to bolts from rear of ignition switch and remove switch. installation is reverse of removal.

Jun 08, 2014 | 1992 Geo Tracker

1 Answer

Need to replace the entire ignition how to remove the steering out of the way


Ignition Switch - REMOVAL & INSTALLATION
(see Figure 1)
  1. Disconnect the negative battery cable.
  2. Remove the lower column trim panel, then remove the steering column-to-instrument panel fasteners and carefully lower the column for access to the switch.
  3. Place the ignition switch in the OFF-LOCK position.
If the lock cylinder was removed on vehicles through 1991, the actuating rod should be pulled up until it stops, then moved down one detent; the switch is now in the Lock position.


zjlimited_463.jpg

Fig. 1: Adjusting the ignition switch

  1. Remove the ignition switch-to-steering column retainers, then remove the assembly.
To install:
  1. Before installing the ignition switch, place it in the OFF-LOCK position, then make sure that the lock cylinder and actuating rod are in the Locked position (1st detent from the top or 1st detent to the right of far left detent travel).
Most replacement switches are pinned in the OFF-LOCK position for installation purposes. If so, the pin MUST be removed after installation or damage may occur.
  1. Install the activating rod into the ignition switch and assemble the switch onto the steering column. Once the switch is properly positioned, tighten the ignition switch-to-steering column retainers to 35 inch lbs. (4.0 Nm).
When installing the ignition switch, use only the specified screws since over length screws could impair the collapsibility of the column.
  1. Raise the column into position and secure, then install any necessary trim plates.
  2. Make sure the ignition is OFF , then connect the negative battery cable.


Ignition Lock Cylinder - REMOVAL & INSTALLATION
(see Figure 1)
  1. Disconnect the negative battery cable.
  2. Matchmark and remove the steering wheel.
  3. Remove the turn signal switch from the column and allow it to hang from the wires (leaving them connected). For details, please refer to the procedure located earlier in this section.
  4. For vehicles through 1991, place the lock cylinder in the Run position.
  5. For 1992-93 vehicles, remove the buzzer switch assembly.
zjlimited_464.jpg

Fig. 1: Ignition cylinder replacement

  1. Carefully remove the lock cylinder screw and the lock cylinder. If possible, use a magnetic tipped screwdriver on the screw in order to help prevent the possibility of dropping it.
CAUTION If the screw is dropped upon removal, it could fall into the steering column, requiring complete disassembly in order to retrieve the screw and prevent damage.
To install:
  1. Align and install the lock cylinder set. On vehicles through 1991 it will be necessary to rotate the switch clockwise to align the cylinder key with the keyway in the housing.
  2. Push the lock cylinder all the way in, then carefully install the retaining screw. Tighten the screw to 22 inch lbs. (2.5 Nm) on tilt columns or to 40 inch lbs. (4.5 Nm) on standard non-tilt columns.
  3. If necessary, install the buzzer switch assembly.
  4. Reposition and secure the turn signal switch assembly
  5. Align and install the steering wheel.
  6. Make sure the ignition is OFF , then connect the negative battery cable.


Keep us updated about your advance.

Jan 13, 2011 | 1987 Chevrolet S-10 Pickup

1 Answer

How to remove two pins holding ignition clyinder lock tumbler from 1994 mercury tracer


Removal & Installation


Before continuing with this procedure, make sure to have available a new steering wheel retaining bolt and two lock cylinder retaining bolts. Once removed, these parts lose their torque holding ability (or retention capability) and must not be reused.

  1. If equipped, disarm the air bag system and disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch.
  4. Unplug the wiring connector to the ignition switch.
  5. Remove the ignition and shifter interlock cable mounting bracket bolt and position the assembly to one side.
  6. Remove the four steering column bracket bolts and lower the steering column.
  7. Cut a groove in the ignition cylinder bracket bolts with a chisel and hammer or use a similar method.
  8. Using a screwdriver, remove and discard the bracket bolts.
  9. Remove the ignition switch lock cylinder and bracket.

c17hydro_34.gif

Unfasten the ignition and shifter interlock cable mounting bracket bolt, and position the assembly to one side



c17hydro_35.gif

Use a chisel and hammer to cut a groove in the ignition cylinder bracket bolts-1991-96 models shown; 1997-99 models similar


To install:

  1. Install the new ignition switch and the bracket into position on the steering column tube.
  2. Install the new lock cylinder bolts and tighten the bolts enough to hold the switch in position.
  3. Check for proper switch operation by rotating the key to each position. If necessary, reposition the lock cylinder until it operates properly.
  4. If positioned properly, tighten the retaining bolts until the bolt head shears off.
  5. Raise and position the steering column. Tighten the bracket bolts to 80-124 inch lbs. (9-14 Nm).
  6. If equipped with tilt column, remove the upper mounting bracket retaining pin.
  7. Position the interlock cable bracket. Install and tighten the retaining bolt to 35-53 inch lbs. (4-6 Nm).
  8. Attach the wiring connector to the ignition switch.
  9. Install the combination switch.
  10. Connect the negative battery cable.
  11. Confirm operational status of the air bag system by turning the ignition key to the RUN position and visually monitoring the air bag indicator lamp in the instrument cluster. The indicator lamp should illuminate for approximately 6 seconds and then turn OFF. If the indicator lamp does not illuminate, stays ON, or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
  12. Check the steering wheel, horn and combination switch functions for proper operation.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Nov 20, 2010 | Mercury Tracer Cars & Trucks

1 Answer

How do I locate the ignition switch and remove it from my gmc sierra 1991 ignition switch


The ignition switch is located on the top of the steering column underneath the dash.

1. Remove the cover panel from under the steering column and you should see the bracket that holds up the steering column, but before you un-bolt the bracket to lower the steering column, you must remove the clip holding the shifter position indicator cable to the column. (put the shifter into drive and you should be able to see the screw that holds the shift indicator cable adjusting clip to the steering column)

2. Remove the bracket holding up the steering column and carefully let the steering column down as far as it will go, the steering wheel will probably be resting on the seat.

3. You should now be able to see the ignition switch on the top of the steering column, and the two mounting bolts. The high beam switch might share the upper ignition switch bolt, and you will then need to remove the high beam switch before you can remove the ignition switch.

4. Remove the ignition switch mounting bolts (usually 5/16 but I have also seen 11/32 and 3/8 size bolt heads used)

5. Remove the ignition switch by lifting straight up from the column to dis-engage the interlink rod from the ignition tumbler assembly, you should then be able to pull the ignition over towards you just enough to dis-connect the two wire connectors to the switch and then you can remove the old switch from the vehicle. (the interlink rod is sticking straight up from the steering column and it slides up and down with the operation of the key, it fits into a notch in the ignition switch and that is what actuates the switch)

6. Reverse procedure to install new switch, starting with re-connecting the wire connectors and be sure that the interlink rod goes into the notch in the ignition switch.

7. When the switch has been re-installed and is ready to be adjusted, turn the ignition switch to the "ON" position and hold the key in that position and slide the ignition switch up and down until it is in the on position and your dash lights come on, tighten up the ignition switch mounting bolts and then test the operation of the switch, and re-adjust if necessary until the switch operates properly.

8. Adjust the high beam switch by pulling back on the high beam lever and just taking up the slack in the actuator rod to the high beam switch, test the operation of the high beam switch and re-adjust if necessary.

9. When the steering column is bolted back up, re-attach and adjust the shifter position indicator by placing the shifter in neutral and slide the adjusting cable clip until the shift indicator is pointing in the neutral position, test the function of the shift indicator and adjust as necessary.

Apr 24, 2010 | 1991 GMC Sierra

1 Answer

Need to replace an ignition switch- how do i do it


The steering column needs to be dropped to get at it.

Put blocks behind your tires, your car could shift out of park while repairing.

First remove the dash cover below the steering column. Carefully remove the metal clip for the transmission gear shift indicator, and note it's position. Then remove the two bolts from the metal bracket holding the column in place. It should float freely now.

The ignition switch is on top of the column, on the left side. There should be a metal rod and a whole bunch of wires running to it. There are two screws holding the bracket to the column.

Be careful with that rod, if it falls out of the column, it is almost impossible to put back!

I don't know what a new ignition switch comes with, but there should be some instructions for wiring.

Good luck!

Mar 15, 2010 | 1995 Buick LeSabre

1 Answer

Can't get the ignition out. I need to replace it because the key broke off how do I get the old ignition out. I have the key out.


PLEASE DON'T FORGET TO RATE!!!!

Some models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.


Before continuing with this procedure, make sure to have available a new steering wheel retaining bolt and two lock cylinder retaining bolts. Once removed, these parts lose their torque holding ability (or retention capability) and must not be reused.
  1. If equipped, disarm the air bag system and disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch.
  4. Unplug the wiring connector to the ignition switch.
  5. Remove the ignition and shifter interlock cable mounting bracket bolt and position the assembly to one side.
  6. Remove the four steering column bracket bolts and lower the steering column.
  7. Cut a groove in the ignition cylinder bracket bolts with a chisel and hammer or use a similar method.
  8. Using a screwdriver, remove and discard the bracket bolts.
  9. Remove the ignition switch lock cylinder and bracket.


59e4e76.gif
Unfasten the ignition and shifter interlock cable mounting bracket bolt, and position the assembly to one side


5ad8b44.gif
Use a chisel and hammer to cut a groove in the ignition cylinder bracket bolts-1991-96 models shown; 1997-99 models similar

To install:
  1. Install the new ignition switch and the bracket into position on the steering column tube.
  2. Install the new lock cylinder bolts and tighten the bolts enough to hold the switch in position.
  3. Check for proper switch operation by rotating the key to each position. If necessary, reposition the lock cylinder until it operates properly.
  4. If positioned properly, tighten the retaining bolts until the bolt head shears off.
  5. Raise and position the steering column. Tighten the bracket bolts to 80-124 inch lbs. (9-14 Nm).
  6. If equipped with tilt column, remove the upper mounting bracket retaining pin.
  7. Position the interlock cable bracket. Install and tighten the retaining bolt to 35-53 inch lbs. (4-6 Nm).
  8. Attach the wiring connector to the ignition switch.
  9. Install the combination switch.
  10. Connect the negative battery cable.
  11. Confirm operational status of the air bag system by turning the ignition key to the RUN position and visually monitoring the air bag indicator lamp in the instrument cluster. The indicator lamp should illuminate for approximately 6 seconds and then turn OFF. If the indicator lamp does not illuminate, stays ON, or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
  12. Check the steering wheel, horn and combination switch functions for proper operation.

Oct 22, 2009 | 1994 Ford Escort

1 Answer

I need to change my ignition cylendar.


Ignition Lock Cylinder REMOVAL & INSTALLATION 1997–99 Models CAUTION
Some models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6. NOTE: Before continuing with this procedure, make sure to have available a new steering wheel retaining bolt and two lock cylinder retaining bolts. Once removed, these parts lose their torque holding ability (or retention capability) and must not be reused.
  1. If equipped, disarm the air bag system and disconnect the negative battery cable.
  2. If necessary, remove the steering wheel.
  3. Remove the combination switch.
  4. Unplug the ignition switch wiring connectors.
  5. Remove the ignition and shifter interlock cable mounting bracket bolt and position the assembly to one side.
  6. Cut a groove in the ignition cylinder bracket bolts with a chisel and hammer or use a similar method.
  7. Using a screwdriver, remove and discard the bracket bolts.
  8. Remove the ignition switch lock cylinder and bracket. To install:
  9. Install the new ignition switch and the bracket into position on the steering column tube.
  10. Install the new lock cylinder bolts and tighten the bolts enough to hold the switch in position.
  11. Check for proper switch operation by rotating the key to each position. If necessary, reposition the lock cylinder until it operates properly.
  12. If positioned properly, tighten the retaining bolts until the bolt head shears off.
  13. Position the interlock cable bracket. Install and tighten the retaining bolt to 35–53 inch lbs. (4–6 Nm).
  14. Attach the wiring connector to the ignition switch.
  15. Install the combination switch.
  16. If removed, install the steering wheel.
  17. Connect the negative battery cable.
  18. Confirm operational status of the air bag system by turning the ignition key to the RUN position and visually monitoring the air bag indicator lamp in the instrument cluster. The indicator lamp should illuminate for approximately 6 seconds and then turn OFF. If the indicator lamp does not illuminate, stays ON, or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
  19. Check the steering wheel, horn and combination switch functions for proper operation.
Fig. 1: Unfasten the ignition and shifter interlock cable mounting bracket bolt, and position the assembly to one side

72a6db6.gif
Fig. 2: Use a chisel and hammer to cut a groove in the ignition cylinder bracket bolts — 1991–96 models shown; 1997–99 models similar

9849583.gif

Aug 30, 2009 | 1998 Ford Escort

1 Answer

Ignition switch removal


get a proper steering wheel puller, pull the steering wheel off. remove the screw for the hazard switch. remove 1 screw and a metal bracket for the signal switch. remove 3 screws holding the white switch in top of column. Then you need to pull this switch up out of the way, but in order to do this without wrecking it, you need to remove the plastic panels underneith the column to get at the column mounting bolts. there should be 2 13mm nuts holding the column to the dash. remove these. then there should be 4 13mm bolts holding the bracket to the column. remove these and there should be a plastic casing that th wires go through. remove this and unplug the wiring. now you can push the wiring up and out of the way without wrecking your signal switch. now remove 1 philips head screw holding the ignition switch in place and pry it out gently with a flat screwdriver.

installation is reverse procedure of removal

Mar 22, 2009 | 1988 Pontiac Firebird

1 Answer

How to take the egnition switch of??


you can access the ignition switch from underneath the dash, but I found it easier to remove the steering wheel, then the instrument cluster. There are two basic elements to the ignition switch. The part that usually breaks down first is the front section, where the key goes into. You have to remove the entire unit from its bracket. Unplug the wire loom from the back of the housing. I believe there are two screws holding both sections together. Remove the screws and replace the unit. Then re-assemble.

Mar 17, 2009 | 1985 Mercedes-Benz 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...