Question about 2003 Oldsmobile Silhouette

Open Question

How to replace thermostat in 2003 oldsmobile silhouette

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
autodr
  • 260 Answers

SOURCE: Olds silhouette heater blows cold air

as long as the engine temperature is normal, i would suspect a clogged heater core, the dex-cool antifreeze is notorious for building up deposits in cooling system. have heater core flushed first to see if it makes any difference

Posted on Nov 16, 2008

Ad
  • 2 Answers

SOURCE: Replacing dashboard lights on an 2000 Oldsmobile Silhouette Van?

the light bulbs are not replacable unless you can solder, you have to replace the complete instrument cluster, get one from a junk yard 100 bucks.

Posted on Sep 25, 2008

keeperoffire
  • 106 Answers

SOURCE: 2002 Oldsmobile Silhouette ABS Light is on and

The first thing i would check is all 4 abs sensors at the wheels.You can do this with a volt meter set on ac voltage and spin the wheel if it generates voltage at all on the meter its good.

Posted on Mar 06, 2009

  • 8 Answers

SOURCE: lower intake manifold gasket leaking 02 Olds Silhouette

This is basicly a very time consuming job rather than a physically hard one to complete. In order to replace the gasket you must remove the intake plenum,throttle body, and misc. vacuum hoses. The wiring harness connections must also be disconnected. Finally the intake manifold is exposed. The bolts holding the manifold to the block are removed exposing the leaking gasket. After removing the push rods and placing them in the correct order to be replaced the gasket and sealants can be removed. Finally replace everything in reverse order. Be sure to consult a GM manual for correct bolt torch specs. The correct specs for the manifold bolts usually come with the gasket. Make sure to change your oil a few times after this job in case any coolant entered the block. Also,change the thermostat and the oil seal on the distributor half shaft cap while you have everything off. Good Luck

Posted on May 12, 2009

  • 1986 Answers

SOURCE: Replacing mirror on 1998 Oldsmobile Silhouette

you'll need to remove your door panel (screws are by the door handle, arm rest, under door and side of door) and remove the cover adjacent to your mirror to remove the bolts to remove the mirror.

Posted on Aug 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace power steering pump 2003 oldsmobile silhouette


Never done one on an the silhouette, and you didn't include the engine size of your van, but I imagine in would be similar to the one in this video.

Feb 17, 2015 | Oldsmobile Cars & Trucks

1 Answer

Replace thermostat 1999 silhouette


Thermostat it's located by the ignition

Mar 04, 2014 | 1999 Oldsmobile Silhouette

1 Answer

Location of thermostat/housing unit in silhouette 2003


Follow the upper radiator hose to the engine. The part that the hose attaches to on the engine is the thermostat housing. The thermostat is behind that housing. It is not an easy on to do but with the right tools it can be done.

Apr 11, 2013 | 1999 Oldsmobile Silhouette

1 Answer

No heat on oldsmobile silhouette 2003 and over heating


Are you sure the radiator and overflow tank are full of coolant ?

Jul 17, 2012 | 2003 Oldsmobile Silhouette

1 Answer

Thermostat replacement 1991 olds silhouette


follow the big hose from the top of the radiator to where it goes into the engine. At the engine you will see typically 2 bolts to remove. under that is the thermostat. if it has rubber gasket, simply replace the thermostat and gasket. If it is a paper gasket, CLEAN THOROUGHLY, then rplace using some sort of gasket glue, many types available, they all will work.

Jan 05, 2012 | 1991 Oldsmobile Silhouette

1 Answer

How to change a thermostat on 1999 Oldsmobile Silhouette?


The thermostat is on the end of the engine (driver's side), by the transmission. See figure below. Also, please see my tip at http://www.fixya.com/cars/r5929960-s_thermostat and let me know if you have questions.

Nov 14, 2010 | 1999 Oldsmobile Silhouette

1 Answer

How to replace thermostate


usually its under the top hose housing

Jul 05, 2010 | 2000 Oldsmobile Silhouette

1 Answer

2003 Oldsmobile Silhouette. Parked van went into gear on own


Please have a dealership that handles GM vehicles check to see if your vehicle was involved in what the trade considers a run away transmission condition involving the automatic transmissions parking pall linkage defecting thus allowing the transmission to go into drive while the vehicle is idling in park.

May 09, 2010 | 2003 Oldsmobile Silhouette

1 Answer

Auto traction and cruise control problems


Just replaced both front bearings on my 2000 olds silhouette, the traction control light / ABS light is still on. What do i do?

Jul 01, 2008 | 2003 Oldsmobile Silhouette

Not finding what you are looking for?
2003 Oldsmobile Silhouette Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...