Question about 2008 Ford F 250 Super Duty 4WD

Open Question

How to replace the front dome light bulb in a 2008 F250 King Ranch

What holds the front dome light assembly to the roof of the vehicle? Can I pull it down without damaging to replace the bulbs?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
osoteddy
  • 1 Answer

SOURCE: How to replace map & dome light bulbs on a 2008 Ford F-150 Super

2008 Ford F-150 SuperCrew Cab (without moon roof or rails): How to replace the map light bulbs.  First, you'll need a "trim pad remover."  It is a tool with a screwdriver handle and the metal part has a 'smooth' forked tongue (see Snap-on Stock#: A177A for picture).  Go to the center counsel and "gingerly" work around he counsel and pull down at the same time.  The counsil is held in by six snap in tongs.  It should remove pretty easily.  once down, you'll see where the bulbs are.  Unscrew and replace.  Now, just line up the tongs and gently bump or hit the pressure points (where the tongs are) and it should snap into place.  It should take no more than five minutes, tops.

Posted on Nov 17, 2008

Ad
sscullys
  • 984 Answers

SOURCE: removing dome light for replacement of bulb do you

The non rail roof panel is held in place with spring clips. The 1st time you take it down, it will be a very hard pull. Open the rear compartment ( that the inserts go into for sun glasses and the likes ) and pull on each corner, this will get the back clips off, and make it easier to pull down on the front.

Posted on Nov 14, 2010

kearst14
  • 7 Answers

SOURCE: need to replace bulb for front parking light/turn signal on a 94 ford probe

There should be a cover on the back of the assebly. a few crews and some metal clips. I dont think you have to remove the whole assembly to change it if i remember right. it should just be a protective cover.

Posted on Sep 16, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2010 F250 King Ranch and the wrench light comes on and off occasionally and on occasion vehicle will just shut off and display to pull over safely.


Eric, The wrench symbol is telling you maintenance is required.
You will have to have truck scanned for diagnostic codes to determine the problem.

Mar 27, 2016 | Cars & Trucks

1 Answer

Directions on how to replace fog ligt bulbs on a 2008 elantra


  1. You may have to jack up the front end of the car to be able to slide under the vehicle a bit or if your arms are long enough you should be able to reach underneath the vehicle and feel for the connector.
  2. So now you see the connector simply give a turn counterclockwise and it will come loose.
  3. Now pull the bulb assembly out.
  4. The fog lamp will pull strait out of the connector.
  5. Replace with a new 9006 bulb.
  6. Now put the bulb assembly back in the fog light assembly.
  7. Turn the bulb assembly clockwise till it click's.
  8. Job completed.
ironfist109_15.gif
Regards, Tony

Apr 30, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

Removing dome light for replacement of bulb do you just pull down on plactic frame ?


The non rail roof panel is held in place with spring clips. The 1st time you take it down, it will be a very hard pull. Open the rear compartment ( that the inserts go into for sun glasses and the likes ) and pull on each corner, this will get the back clips off, and make it easier to pull down on the front.

Jul 26, 2010 | 2008 Ford F 150 2WD

1 Answer

How do I change out the dome lite on my 2005 150 king ranch


For a 2005 MY F-150 :
The rear ( if SCab or SuperCrew ) there is a little notch in the lens that is used to push in a tab and lower that side, slide out from the back.

The front, non rail system is open the rear sunlgasses compartment, and grab each corner. Pull down, there is 4 or 6 spring clips that hold the overhead console to the roof. Once down, you will see the gray bulb holders. Twist out the bulb holder, and the bulb plugs into the holder. They are 2 element over sized 194 type bulbs ( think it is a 39 or 67 ??? not sure on that ).
Rail system is slightly different

Jan 04, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Tail light change in 2001 Ford F150 King Cab


lower tailgate.look for small 8 or 10mm bolts that hold tail light assembly in place .remove bolts,pull assembly off.there are also plastic 'pins' that align and help hold the tail light.grasp bulb socket and twist to remove.pull bulb straight out.

Sep 22, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I want to replace the bulb in a 2001 Dodge Intrepid dome light.


pops on pops off from front to back not side to side pry gently as the clips are cheap.

Jun 10, 2009 | 2001 Dodge Intrepid

1 Answer

How to take out the light assy on a 2004 Toytota sienna van.RH side. Do you have to take off the front cap (bumper)


Yes....herer is the steps to replacing it:

Headlight Assembly Removal & Installation Standard Headlights To Remove:
  1. Disconnect the battery ground cable.
  2. Remove the left and right front inner fenders. Fog light & headlight assembly (exploded view) toyota-06-00-5662.gif

  3. Remove the 8 screws and separate the front splash shield from the front bumper fascia.
  4. Remove the 5 push-pins from the top of the fascia grille.
  5. Release the retainers on the left and right sides of the front bumper fascia and pull the fascia toward the front of the vehicle.
  6. Disconnect the headlight assembly connectors.
  7. Remove the mounting bolt, 3 screws and headlight assembly.
  8. Turn all bulb sockets counterclockwise to remove.
To Install:
  1. Turn all bulb sockets clockwise to install.
  2. Align the retainers with the slots and install the front fascia.
  3. Install the 5 push-pins on top of the fascia grille.
  4. Install the front splash shield on the front bumper fascia with the 8 screws.
  5. Install the left and right front inner fenders.
  6. Connect the battery ground cable.
  7. Vehicles with power windows perform the following steps:
    • Turn the ignition switch on.
    • Open the power window halfway.
    • Close the window and continue to hold the switch up for at least 1 second after the window is closed.
    • Ensure that the auto up/down circuit is operating properly.
    • If the auto up/down circuit does not operate, disconnect the battery ground cable for 10 seconds.
    • Connect the battery ground cable.
    • Turn the ignition switch on.
    • Open the power window halfway.
    • Ensure that the auto up/down circuit is operating properly.
    • If the auto up/down circuit does not operate, turn the ignition switch on.
    • Open the power window halfway.
    • Close the window and continue to hold the switch up for at least 12 second after the window is closed.
  8. Vehicles with sliding roof system perform the following steps:
    • Turn the ignition switch on.
    • Press and hold the TILT UP switch until the glass tilts to the full up position. The glass will automatically tilt slightly down after it reaches the up position.
    • Release the switch.
    • If the sliding roof does not operate properly, replace the sliding roof ECU.

May 07, 2009 | 2004 Toyota Sienna

3 Answers

Map light removal on a 2008 Ford f350


I had the same issue with my 2008 w/ moonroof. It's tough but you just have to evenly apply pressure on both sides and pull it straight down. There's two pressure clips that are holding it. I replaced with LEDS, the rear was tough as well!

Feb 27, 2009 | 2004 Ford F150

1 Answer

How to replace map & dome light bulbs on a 2008 Ford F-150 Super


2008 Ford F-150 SuperCrew Cab (without moon roof or rails): How to replace the map light bulbs.  First, you'll need a "trim pad remover."  It is a tool with a screwdriver handle and the metal part has a 'smooth' forked tongue (see Snap-on Stock#: A177A for picture).  Go to the center counsel and "gingerly" work around he counsel and pull down at the same time.  The counsil is held in by six snap in tongs.  It should remove pretty easily.  once down, you'll see where the bulbs are.  Unscrew and replace.  Now, just line up the tongs and gently bump or hit the pressure points (where the tongs are) and it should snap into place.  It should take no more than five minutes, tops.

Nov 16, 2008 | 2004 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

511 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...