Question about 1998 GMC Yukon

1 Answer

Lost reverse, sluggish 1st gear

Heard felt a bang/clunk couple times, now no reverse

Posted by on

  • rglomski Jan 21, 2009

    has no 2nd, 4th or reverse...needs planetary gears, shell, gmc has tsb on this

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

You will need to get the Tranny Shift Kit Inspected for Shifting Ball Slippage. Should not be a Big Repair unless it messed up the Clutches inside the Tranny.

Posted on Jan 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear differential clunk


Have the drive shaft and axle joints checked one or more is worn out.

Feb 20, 2014 | BMW Cars & Trucks

1 Answer

2003 chevrolet cavalier, manual transmission lost 2nd, 4th and reverse but still has 1st, 3rd and 5th gears.


Sounds like one of the levers inside the transmission is either broken or otherwise disengaged. Remove the shifter to see if you can see any obvious reason.

Aug 25, 2012 | 2003 Chevrolet Cavalier

1 Answer

2005 Corolla's manual trasmission shifts gears, it clunks


hi mate , sounds like the SPIGOT bearing its a little bearing that allows the gearbox to be at a different seed than the engine flywheel and if this is in bad condition it will take the gearbox front shaft to a higher speed than comfortable for gearshift , in the meantime when you go for 1st or reverse gear just engage a gear like 4th without taking your foot off the clutch and then go for 1st or reverse, this will stop the gearbox spining long enough for a smooth shif, oNLY USE THIS METHOD WHILE STaTIONARY and see a professional when you get time.

Mar 29, 2010 | 2005 Toyota Corolla

1 Answer

Only runs in 1st and 2nd gear and reverse.


This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Dec 14, 2009 | 2006 Hummer H3

1 Answer

No reverse and shifts hard if forward gears


best bet is call scrap yard they are fairly decent priced unless you want new

Aug 25, 2009 | 1996 GMC Jimmy

1 Answer

TR6 Clunking


Does it go away or change when you depress the clutch. If so you will need to inspect the clutch pressure plate and bearing. You may need to remove trans. You may have a loose bolt on the flywheel that backed off a little.

Aug 14, 2009 | 2006 Triumph Tr 7

1 Answer

No reverse


U are going to have to have the trans torn down and replace the reverse clutch drum.

Nov 22, 2008 | 1999 Chevrolet Silverado 1500

2 Answers

Lost all gears except 1st


your clutch pedal has broken easy fix

Oct 23, 2008 | 2000 Volkswagen Golf

Not finding what you are looking for?
1998 GMC Yukon Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...