Question about Honda Civic

Open Question

Water pump bolts on a 2001 civic 1 is short where does it go

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 69 Answers

SOURCE: change water pump on 2001 hyundai tiburon

It is a 2.0L (the delta blocks weren't in tibs until '03). You have to remove the timing belt tensioner, and then you can remove the bolts for the water pump. I would strongly recommend not only taking careful precaution not to disturb the orientation of the gears in this process, but also to replace the timing belt and water pump at the same time. You don't want to go through this process all over again do you?

Posted on May 27, 2009

mkv0525
  • 358 Answers

SOURCE: what are specs for water pump bolts for 2001

Home | Account | Contact ALLDATA | Log Out | Help ALL TUNE & LUBE DDG AUTOMOTIVE Select Vehicle | New TSBs | Technician's Reference Component Search: Conversion Calculator 2001 Ford Taurus V6-3.0L VIN 2 Flex Fuel Vehicle Level Specifications Mechanical Specifications Water Pump Water Pump Water Pump Notes Engine Front Cover and Water Pump Assembly 25 Nm (18 lb-ft) © 2009 ALLDATA LLC. All rights reserved. Terms of Use

Posted on Jun 10, 2009

dttech
  • 4803 Answers

SOURCE: 1994 buick 2.2 water pump bolt size?

Ron,
Thank you for asking me to help you with your problem. However, this is either not within my level of expertise or the question is unclear or there is not enough information and I cannot help you at ths time.

Posted on Dec 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If you put a long bolt where a short bolt is suppose to go what could happen for a water pump 2001 toyota corolla


The water pump might leak (externally) around that bolt. Worst case would be the bolt pokes a hole into the engine and water leaks into the oil passage.

Dec 30, 2014 | Cars & Trucks

1 Answer

Car cuts off going down the road every now and then. Cranks right up afterwards. Somtimes it can go days without doing it.


It sounds to me that your fuel pump is momentarily getting shut off. I came across just about the same problem with a 93 civic. Eventually the civic fuel pump wouldnt come on at all. after troubleshooting it for days and, 2 used ebay computers later, we found the problem. There was water getting to the computer which would short out the fuel pump circuit, then eventually burn up the circuit from the computer to the pump. I cleaned the area of all the water, and sealed it off from water where i thought it was coming in from and havent had a problem in 2 years now. Check to see if any water or moisture is getting in your computer box.

Apr 15, 2013 | 2001 Honda Accord 3.0 EX

1 Answer

2001 Honda Civic overheating problem


what would cause the 2001 honda civic to over heat after brand new water pump theromastat timing belt and alternator blet replace yesterday and when it overheated i pulled over and checked all the fluids i had like oil or transmission fluid all over my under part of motor alittle on my breather and top part of hood , the oil also has a tendency to smell like gas but its not oil/gas mixture please help

Jan 18, 2012 | 2001 Honda Civic

1 Answer

How do i change a waterpump on a 2001Volkswagen cabrio?


Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



archaeology_93.jpg

Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:



archaeology_94.jpg



Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:



archaeology_95.jpg


Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Sep 13, 2011 | 2001 Volkswagen Cabrio

1 Answer

I took off the old water pump and now I can't remember which bolts go where. Some are short and some are long. I need a diagram that shows the bolts and where they go. There are 7


Try installing the short bolts first. If they won't start or only screw in a few threads, then that hole is probably for a longer bolt.

Jan 22, 2011 | 2001 Dodge Dakota

1 Answer

How do you change a water pump on a 2001 nissan altima?


Just did this over the weekend with my 2001 Nissan Altima. First, remove the negative battery cable to prevent shorting. Drain the radiator by removing the drain screw. To gain access to the water pump, I had to remove the upper radiator hose to the engine, unattach the reserve tank hose from the radiator and take out the reserve tank, remove the alternator and the lower alternator bracket because it blocks access to one of the water pump bolts and move the serpentine belt out of the way. This should give you free access to the six bolts that attach the water pump. You will probably have to hit the water pump with a rubber mallet or some other tool to break the sealant on the water pump, but it should then just come off. The hardest part of the job for me was removing the bolts for the alternator bracket because they were on extremely tight. Reinstall your new water pump after applying sealant to all parts that will attach to the bracket, and your ready to put it all back together. If you have the right tools, this should take probably 4 or 5 hours to complete.

Aug 06, 2010 | 2001 Nissan Altima

1 Answer

How to replace a water pump on a 2001 ford taurus


This is for a 3.0L and VIN S engine--

VIN U Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt and tensioner
    • Water pump pulley
    • Heater hose
    • Engine control sensor wiring
    • Water pump
54afbf0.gif
To install:
NOTE The water pump bolts are of different lengths and must be installed in the correct locations.

  1. Install the water pump. Tighten bolts 1, 2, 3, 4, 5, 6, 7, 8, 9 and 15 to 15–22 ft. lbs. (20–30 Nm). Tighten bolts 10, 11, 12, 13 and 14 to 72–106 inch lbs. (8–12 Nm). Refer to the accompanying illustration for the bolt locations.
  2. Install or connect the following:
    • Engine control sensor wiring
    • Heater hose
    • Water pump pulley and tighten the bolts to 15–22 ft. lbs. (20–30 Nm)
    • Accessory drive belt and tensioner
    • Negative battery cable
  3. Fill the cooling system and check for leaks

Dec 08, 2009 | 2001 Ford Taurus

1 Answer

Replacement of Water Pump. 2001 Chevy Cavalier 2.4 L


Stick with me on this
1.Put the car on jack stands
2.Remove the exhuast manifold, Do not rotate the flex cuopling more then 4 degrees od damage will occur.
3.Diconnect the coolant inlet pipe from the water pump outlet hose, Disconnect from the engine, disconnect it from the thermostate housing and remove it.
4.lower the car back down of the jack stands.
5.Detach the brack booster hose.
6.Remove the timing chain cover and the tensioner.
7.Remove the heater outletpiper from the water pump.
8.Remove the water pump cover bolts.
9.Remove the water pump retianer nuts.
Remove the old gasket and clean.
10.On bench. Install the waterpump and cover but lreave the bolts finger tight.
11.Install back in car, leave water pump bolts looseto allow for positioning.
12.Install water pump cover to engine, tighten by hand.
13.Lubricate oringand install metal outlet pipe back into pump, hand tighten.
14a.Tighten the water pump to timing chain nuts
14b.Tighten the water pump cover to water pump housing bolts.
14c.Tighten water pump cover to engine block bolts.
14d.Tighten the radiator outlet pipe to water pump.
15.Install timing chain tensioner.
16.Install exhuast manifold.
17.Install exhuast pipe.
18. Fill it up and bleed the system.
Good luck

Jul 02, 2009 | 2001 Chevrolet Cavalier

1 Answer

Looking for directions, pictures, on how to change water pump


Water Pump Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    • Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    • Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
  2. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
  3. Install the support bracket.
  4. Install the accessory drive shaft tensioner.
  5. Install the generator.
  6. Install the roll restrictor bracket, bolt and the nut.
  7. Install the water pump pulley.
  8. Install the accessory drive belt.
  9. Connect the battery ground cable.
  10. Fill the engine cooling system.
2918819.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jun 26, 2009 | 2001 Ford Taurus

1 Answer

What are specs for water pump bolts for 2001


Home | Account | Contact ALLDATA | Log Out | Help ALL TUNE & LUBE DDG AUTOMOTIVE Select Vehicle | New TSBs | Technician's Reference Component Search: Conversion Calculator 2001 Ford Taurus V6-3.0L VIN 2 Flex Fuel Vehicle Level Specifications Mechanical Specifications Water Pump Water Pump Water Pump Notes Engine Front Cover and Water Pump Assembly 25 Nm (18 lb-ft) © 2009 ALLDATA LLC. All rights reserved. Terms of Use

Jun 10, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...