Question about Chrysler Sebring

Open Question

04 sebring 2.7 motor the code is p0171 are not what is the problem im replace tha o2 sensor

Im replace the 02 sensor buut the ligth check engine is come on again

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: Code #P0171 & code #P0174

The most common problem on a Ford with these codes is deteriorated PCV hoses. Check the hoses from the PCV valve to the intake manifold. Pay special attention to the rubber elbows. They often crack on the inside curve and the crack is hard to see.

Posted on May 22, 2008

  • 4 Answers

SOURCE: Code #P0171 & code #P0174

The intake manifold gaskets need replacement as well as the o-rings inside - if you call FORD they should be able to get you the correct parts.

Posted on Nov 05, 2008

  • 112 Answers

SOURCE: 2002 Pontac Grand Prix GTP P0171 code engine stumbling at times

Bank 1 is the frt side exhaust manifold (did they say bank 1 sensor 1?),you can start by replacing that sensor,i would check the intake for leaks ,the gm 6cly. are known for bad intake gaskets,you will see oil coming out form the frt or rear of the intake,also check your atifreeze overflow bottle for bronwish sludge,which means that the oil is mixing with the antifreeze.A leaking intake could cause that lean condition.

Posted on Mar 29, 2009

  • 295 Answers

SOURCE: Solving the following Error Codes

The codes you have metion is for fuel injection miss fires. and lean condition . These codes most likely mean you need to start with a tune up , and fuel injection cleaning . The oxygen sensor are very common problem with the po171,po174 code. The other common problem with the codes after a tune up is done is the intake manifold gasket is leaking .
I would take the vehicle in to a mechanic for a tune up and then demand the mechanic clears all the codes . You can take the vehicle back and drive it for a few weeks. IF the codes come back then have the vehicle recheck for the oxygen sensors or intake gaskets .

Posted on Apr 30, 2009

  • 52 Answers

SOURCE: 1996 Dodge Dakota 8 cylinder code P0171

there is only one oxygen sensor.. it is located in the exhaust pipe comming out of the engine jusy at the starting of exhaust... u can easily find it and replace it..

Posted on Aug 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a PO171 code on my 1999 Jeep grand cherakee larado can You tell me how to fix it, Thank You.


  • Dale, code P0171 fuel system too lean
  • Possible causes
  • change fuel filter first, if it has not been done recently
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP INLET STRAINER PLUGGED
FUEL PUMP MODULE
O2 SENSOR
O2 SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
O2 SENSOR HEATER OPERATION
TPS VOLTAGE GREATER THAN 0.92 VOLTS WITH THROTTLE CLOSED
TP SENSOR SWEEP
MAP SENSOR OPERATION
ECT SENSOR OPERATION
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR (HIGH)
PCM
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

2000 Jeep Grand Cherokee p0171

Possible problems related to Code P0171 Jeep Garage Jeep Forum

P0171 System to Lean Bank 1

Code P0171

Mar 11, 2016 | Cars & Trucks

1 Answer

I have five codes P2237 P2196 P2271 P0030 P0171 and a P2237 pending code on a 2005 elantra.The car runs poorly, bad gas mileage, sluggish with the check engine light on.Are all O2 sensors bad or maybe the...


P2237 P2196 P2271 P0030 P0171

These are all O2 sensor trouble codes, except P0171 which is a fuel trim code,

You have a bad 02 sensor - up stream - Bank 1 Sensor 1.

Replace it, then road test. The engine computer has a 'default' fuel trim it uses when an O2 sensor fails so it can protect the catalytic converter. If this hasn't been going on too long, good chance simply replacing the O2 sensor will remedy your problem.

Feb 06, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

I have a 1997 Chevy Blazer with the 4.3 engine. The Service Engine light keeps coming on. I scanned the codes and replaced the O2 sensor just before the catalytic converter. The light is still coming on...


P0146 pd means pending code
Pending codes and DTCs? Posted on November 12, 2010 by fcrmaster
When reading codes from your vehicle the fault code reader may show them as pending codes or normal Diagnostic Trouble Codes (DTC).
Pending codes (also known as continuous monitor codes) will be registered when an intermittent fault occurs. If that fault does not happen again after x number of start/stop cycles, the ECU will erase the code from memory. If the fault is persistent it becomes a DTC.
If you have read pending codes it is advisable to check the codes again after a week or so. If there is no apparent problem with the vehicle it is safe to erase the codes too and check back. But always make a note of any fault codes with the date and mileage of a vehicle.
If the codes read include a DTC then you need to investigate further. This you can either do yourself or advise your garage. If, again, you don't see an apparent problem (depending n the severity of the code) with the vehicle you can note the codes down and erase them. Then check again after a week or a few days depending on how often the vehicle gets used. If a repair has been made (previous owner) the DTC may just not have been reset after the repair.
The other numbers behind the code 01/06 , 02/06, 03/06 , 05/06 ,04/06 These don't mean anything . cheap code reader .
DTC P0140 HO2S Circuit Insufficient Activity Sensor 2
DTC P0146 HO2S Circuit Insufficient Activity Bank 1 Sensor 3
DTC P0171 Fuel Trim System Lean Bank 1
DTC P0174 Fuel Trim System Lean Bank 2
Sorry but this is something you should take to a qualified repair shop that has a diagnostic tool that can view sensor scan data.
Causes of lean condition trouble codes P0171 P0174 GM 5 3L

Jul 23, 2017 | 1999 Chevrolet Camaro

2 Answers

I change the 02 sensors,and after few minutes driving the cheking engine ligth comes on,I eraser with the compuer and the ligth come back on.


You need to find out which code is causing the light to come on. O2 sensors are only one pollible cause. There are tons of possible reasons for that light to be on. Most parts stores will scan a code for free. Diagnosis is something else. In other words, the code could even be an O2 sensor code but the problem might not be the sensor itself. It could be a wiring issue or even your computer. But get a code first then try to figure out which part is bad.

Sep 23, 2010 | 2003 Chrysler Sebring

2 Answers

I have a gmc envoy & the trouble codes are p0107,p0130,p0135 & p0171 can you tell me what the problem can be.


P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)

P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)

P0171 System too Lean (Bank 1)

Check your Manifold Absolute Pressure Sensor, and it might be a good time to install a new Upstream O2 Sensor.

It might also be beneficial to have your fuel pressure checked if the engine is really running Lean, but this may be caused by a faulty O2 sensor.

Jul 19, 2010 | GMC Envoy XL Cars & Trucks

2 Answers

P1166 code displayed on 04 KIA RIO with 1.6 eng. The check engine light came on within 2 Hrs. running time after timing belt repl.


P1166 refer to O2 sensor heater circuits malfunction, HO2 Heater system electrical, bank 1.


Jun 30, 2010 | 2002 Kia Rio

1 Answer

02 sebring, where is bank 1 O2 sensor


The O2 sensor 1/1 is located at the backside of the engine in the exhaust manifold.

0420-engine-trouble-code-2002-sebring-sedan-i

Feb 12, 2010 | 2002 Chrysler Sebring

1 Answer

The engine ligth is on the scnner say the code po


there are four O2 sensors,you need to check the sensor on the drivers side exhaust,the front O2 before the converter

Jan 19, 2010 | 2004 GMC Envoy

2 Answers

Codes p171 and p0174 on a chevy truck?


Subject: 97-05 Vehicles with 4.8 5.3 5.7 and 6.0 Gen III V8 Engines and Misfires on One Bank - kw CEL diagnostics driveability DTC P0171 P0172 P0174 P0175 P0300 P0301 P0302 P0303 P0304 P0305 P0306 P0307 P0308 #PIP3056 - (07/12/2004)

Models: (00-05 Cadillac Escalade - C6 and K6) and (02-05 Chevrolet Avalanche - C1, C2 K1 and K2) and (99-05 Chevrolet Silverado - C1, C2 K1 and K2) and (00-05 Chevrolet Suburban - C1, C2, K1 and K2) and (00-05 Chevrolet Tahoe - C1 and K1) and (99-05 GMC Sierra C1, C2 K1 and K2) and (00-05 GMC Yukon - C1, C2, K1 and K2) and (03-05 Chevrolet Express G1, G2, G3, H1, H2 ) and (03-05 GMC Savana G1, G2, G3, H1, H2 ) and (04-05 Buick Rainier S1, T1 ) and (03-05 Chevrolet Trail Blazer EXT S1, T1 ) and (03-05 GMC Envoy XL XUV S1, T1 ) and (03-05 Hummer H2) and (04-05 Cadillac CTS-V DB) and (98-02 Chevrolet Camaro FB) and (97-04 Chevrolet Corvette YB) and (98-02 Pontiac Firebird FB) and (04-05 Pontiac GTO VB)

The following diagnosis might be helpful if the vehicle exhibits the described symptoms.

Condition/Concern:
Check Engine Light with a P0300 due to 2 - 4 cylinders misfiring on the same bank of the engine. DTCs P0171, P0172, P0174 or P0175 may also set for the misfiring bank.

Recommendation/Instructions:
If the published misfire diagnostic does not isolate the cause, perform the following suggestions as necessary:
  • Perform a fuel injector balance test for all 8 cylinders. If a fuel injector concern exists, it is possible to misfuel an entire bank of the engine, causing multiple cylinders on the same bank to misfire even though the root cause is a single fuel injector.
  • Inspect O2 sensor connections on the misfiring bank for corrosion or water intrusion. If water intrusion is found on the right bank, it may be due to the AC Evaporator Condensation dripping onto the O2 sensor harness. If this condition is found, reposition and shield the harness to prevent a repeat concern and repair the connections.
  • Check for excessive exhaust backpressure using the restricted exhaust diagnosis.
  • Swap the Position 1 O2 sensors side to side to see if the misfires move to the other bank of the engine. If so, replace the O2 sensor.
Please follow this diagnosis process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

NOTE: GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition.

Sep 30, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...