Question about 2007 Chevrolet Express Passenger

1 Answer

Where do I find the adjustor for headlights?

My headlights are low and uneven on my 2007 Express passenger vam. It has a 4 bulb system. Could you tell me where the adjustment screw is located? Thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is a circular opening in the black housing above the headlights accessed when the hood is open. Adjustments can be done through that opening.

Posted on Jan 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 jeep compass low beam doesnt work


Check the fuse for that side yes you have a fuse for each high and low beams for each side

Mar 26, 2013 | 2007 Jeep Compass 2.4

2 Answers

I have a 1995 Ford Explorer Limited and the high beams work but the low beams and fog lights do not, please help....


These trucks are known for bad multifuction switches.
the switch that i talk of is the signal switch , the handle is the switch, it bolts to side of steering column . this switch controls the signals and the headlights and high /low beams. the other thing is the headlight switch connector, the connector some times goes bad and starts to melt or just comes out of the connector. you will need to remove the cover to steering column, the screws are located under the bottom cover in holes. remove cover and check connector and then test for power if you have power going into switch but not coming out then switch is bad.

the last thing is to make sure the bulbs are good , make sure the headlight bulbs are good , and also the driving light bulbs, test for power at the connectors to those lights to.
You will need to do a little testing to find the problem.

Nov 22, 2012 | Cars & Trucks

1 Answer

2007 Mazda 6 headlight


Then the light has a leak and moisture is getting in.

Jul 24, 2012 | 2007 Mazda 6

2 Answers

What is the DRL warning light on the dashboard of my 2007 Honda CRV?


On my 2007 Honda CR-V The DRL code appeared on the dash board. Additionally I had only one high beam (on the passenger side); both low beams were fine, but I did not have a Daytime Running Light on the drivers side. The DRL code was really misleading because the real problem was that the high beam element in the headlight bulb was burned out. Note that the daytime running light is not a seperate bulb -- it is the high beam element which is powered at a low voltage. Once I replaced the head light bulb everything worked fine and the DRL code on the dash board was gone. So if the DRL message appears what you really need to do is replace the headlight bulb (there are YouTube videos which show how to do this - but search for headlight replacement, not for DRL fix). Be careful not to touch the new bulb with you hands since premature burnout can occur from the grease off your skin. I got my bulb from Wal-Mart for $8.88 (it's a 9003/HB2 for the 2007 CR-V) -- that's a pretty cheap fix.

Feb 27, 2010 | 2007 Honda CR-V

1 Answer

Low beam Headlights out. Not the fuses or the


Hi, check the low beam relay, relay's for the headlights should be either near the fusebox, or under the engine compartment, if not this may be hi/lo beam switch, hope this helps :)

Dec 26, 2009 | 2007 Isuzu Ascender 7 Passenger

1 Answer

Driver's side low-beam headlight out


Purchase the correct bulb, open your hood, unscrew the white retaining ring behind the non working lamp when loose turn black connection 1/4 turn counter clockwise till tabs line up pull straight back remove old bulb put on rubber gloves or BE CAUTIOUS NOT TO TOUCH NEW BULB GLASS WITH BARE FINGERS. Oils from your hands an cause bulb to heat unevenly and cause new bulb to explode in the headlight assembly
So with gloved hands open new bulb insert follow steps in reverse to reassemble. Happy Motoring

Feb 27, 2009 | 2008 Mercedes-Benz Mercedes Benz Clk Class

1 Answer

Faulty forward control modules


might just have to have the TIPM reconfigured

Jan 03, 2009 | 2004 Dodge Ram 2500

Not finding what you are looking for?
2007 Chevrolet Express Passenger Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...