Question about Cars & Trucks

Open Question

Xg ute wac rly fuse in the fuse panel blows as soon as i turn the key

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 26 Answers

SOURCE: BLOWING FUSES IGNITION FUSE STARTER

check the ignition hot wire and also check your ignition switch, if you can not find the short area, you have to change the whole wire direct to your fuse box to solve this problem.

wire problem is the hardest case for the car, wish you good luck.

Posted on Jun 24, 2008

emissionwiz
  • 74945 Answers

SOURCE: Fan belt replacement / xg ute 1996

There is a diagram of the belt run under the hood, the belt has has a spring loaded pulley that tensions it.

Posted on Sep 23, 2008

  • 2 Answers

SOURCE: veh wont start

by looking at the wiring diagram for your truck. the pcm1 fuse only feeds the pcm so most likely it is a grounded wire between the fuse block and pcm. follow the wire harness closely between the two and see if its grounded somewhere. also try disconnecting the pcm and see if the fuse still blows. that would isolate the problem to the wiring. it is highly unlikely that the pcm would cause the problem.

Posted on Nov 27, 2008

  • 713 Answers

SOURCE: FUEL PUMP RELAY LOCATION

Fuel pump relay should be in the under hood fuse box. going to be a small relay about 1x1/2 long.

Posted on Oct 03, 2009

pippall
  • 1486 Answers

SOURCE: my signal lights keep blowing a fuse

Replace the signal Relay thats your problem.

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 ford freestar will fuse # 40 in the underhood fuse panel when the key is turned to the run/start position. It would blow before when it was running and cause vehicle not to shift. Had the transmission...


Any applicable trouble codes? Several systems get voltage off that same fuse. oxygen sensors-- canister purge solenoid--ac compressor relay--imrc, intake manifold runner control, has to do with induction-- breathing. And tranny control.
If it blows as soon as the key is turned on, maybe you can narrow it down by unplugging each system one at a time? That may not be conclusive, any system you unplug, there will be less amp draw on the fuse. Just a thought.

Jul 24, 2017 | Ford Cars & Trucks

1 Answer

Why does it blow heater fan motor (fuse) as soon as key is turned?


What else is connect to that circuit if nothing you most likely have a wire touching metal.

Dec 22, 2015 | 2003 Ford F-350 Super Duty

1 Answer

Keeps blowing auto shut down fuse as soon as key is turned on


Could be several things including one of the oxygen sensors, one of the injectors, the coils, or the engine computer.
You will probably need to get a shop manual to get all of the wiring diagrams connected with that circuit. And I would suggest you use a circuit breaker to check each one instead of fuses.
You'll have to disconnect each component until you find the short.

Oct 18, 2015 | 2004 Chrysler Town and Country

1 Answer

Does any one know what codes 87, 87, 12, and 11 mean on an 95 xg outback Ute are, any help would be greatly appreciated.


the easiest way is to check all the fuses is it only the stereo that won't turn if so it could be something else fuses usually control 3-4 things from my experience hope this helps regards Jim

Oct 21, 2012 | Cars & Trucks

1 Answer

Keep blowing turn b/u fuse as soon I turn on key 1993 gmc sierra


Check out your tail lights, sounds like they are grounding out. Remove the bulbs install a new fuse and install one bulb back on at a time and turn the key if one does not blow the fuse then the socket has worn out.

Oct 09, 2012 | 1993 GMC Sierra K1500

1 Answer

Where can I find headlights fuse in 1995 Mercury Villager ? I know the fuse box is inside the car under the steering wheel, but that's not for headlights fuse.


IF HAVE AUTOLAMPS
IP FUSE/RELAY PANEL fuse 26 10A & fuse 20 RLY COIL 10A
POWER DISTRIBUTION BOX UNDER HOOD
H/LAMP 15A
.................................................................................................
IF DAYTIME RUNNING
: i/p fuse relay panel fuse 20 RLY COIL 10A
fuse 3 ENGINE CONT 5A

: LH COMPARTMENT FUSE/PANEL
H/LAMP LH 15A
H/LAMP RH 15A
.................................................................................................
WITHOUT DAYTIME RUNNING LAMPS
: LH ENGINE COMPARTMENT FUSE PANEL
H/LAMP LH 15A
H/LAMP RH 15A
: I/P FUSE/RELAY PANEL
#19 TAIL LAMP 15A

Feb 05, 2010 | 1995 Mercury Villager

1 Answer

Hi i need to know how to hotwire my XG Falcon Ute with smartlock


Get your ignition lights on for 30mins and car will start, if you use another ignition and key and leave ignition lights on for 30 mins the computer will configure and code new key!!!

Jan 01, 2010 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...