Question about Cars & Trucks

1 Answer

Replaced the fan bracket pulley on my 98 lexus gs 400 the car wants to start but won't, someone please help. The car started fine without the serpentine belt before we changed the part and now that the new part is on it won't start

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 5 Answers

Make sure that when you removed the old bracket and installed the new one that you didn't knock off any connectors for any sensors that may be in the same area as the bracket. If there are any sensors that became unplugged then they may be what is keeping your car from starting.

Posted on Dec 31, 2012

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Replacing water pump in 98 Lex GS300

Removal of the crankshaft front pulley/damper can be removed without any damage being caused to the cam belt.
They are a good fit on the shaft, I personaly use a lead tup, weighs 2lbs and will not damage anything if used properly.
Tap equaly all the way round the pulley, that should be ok.

Posted on Jan 12, 2009

  • 398 Answers

SOURCE: audi serpentine belt problem

are you sure you put it on the right way go to autozone.com and get a belt diagram. did you put the belt on upsidedown?

Posted on Mar 07, 2009

mrgreenz
  • 962 Answers

SOURCE: serpentine belt slips off idler pulley

The A/C pully is supposed to spin freely until the AC is activated to run.. The cranshaft pully does not. Replace the tensioner pully. The belt has to fit in between the grooves on the pullys.

Posted on Apr 05, 2009

  • 6982 Answers

SOURCE: serpentine belt slips off

Remove the belt and check all pulleys for side play and wobble...likely you will find one loose (bad bearing) whichever it turns out to be, change it. (likely what killed the belt to begin with.) Also sight down the belt from the side and check that all pulleys are aligned with each other. any variation needs correction. Begin by checking the one you mentioned first.

Posted on May 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 gs 4oo codes p1346 the car shakeing when in drive and when i slow down


it is a variable valve timing performance code. it could have a bad actuator solenoid, a bad cam actuator, low oil pressure or clogged passages, a wiring to control solenoid problem, or a bad controller. most often it is an actuator solenoid at fault.

Mar 14, 2013 | 1998 Lexus Gs 400

2 Answers

Timing belt/crank shaft and camshafts


Yes, that may cause it the misalignment of the timing belt, you can try to check it and put everything back in..

Good luck.........

Aug 20, 2008 | 1996 Lexus LS 400

2 Answers

Fuel pump repair 98 lexus


What part of "fuel pump repair 98 Lexus" do you need help with? Which 98 Lexus? Which engine is the 98 Lexus equipped with?

May 25, 2012 | 1998 Lexus Gs 400

1 Answer

I need a diagram for my 98 lexus gs 400 fuse box


On this website, you find fuse box diagram and description for Lexus GS400 (1998 - 2000)

Lexus GS400 1998 2000 fuse box diagram Auto Genius

Feb 24, 2012 | 1998 Lexus Gs 400

2 Answers

1996 lexus GS 300 starts but won't idle, changed


check the fuel pump fuse in the fuse box

May 22, 2011 | 1996 Lexus GS 300

1 Answer

Water pump needs replacing


water pump is behind the fan pulley bracket. need to take off the timming belt to get to the water pump. also need to remove the distributor covers on bothe sides. 2 boolts that hold the a/c compressor to the fan pulley bracket ,alternator,idler pulley.

Apr 17, 2010 | 1991 Lexus LS 400

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...