Question about 1993 Chrysler New Yorker

1 Answer

What side of a vehicle is considered the left side?

Trying to bleed the braes in proper sequence

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 2 Answers

When u sit in a vehicle thats how u determine the l and r. or in other words the passenger side is the right and the drivers side is left

Posted on Jul 21, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5341 Answers

SOURCE: whatside of the car is considered left rear?

The driver's side is the left side. As when you are facing the same way as the car is facing, or if you were sitting in the car: driver's is left side, passenger side is the right side of the vehicle.

Posted on Dec 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Sequence for bleeding brakes on 2005 jeep liberty with abs


Not 100% sure if this would pertain to your vehicle, as I'm currently not at work, but some vehicles require bleeding sequence of front left, right rear, right front then left rear.

Mar 16, 2017 | 2005 Jeep Liberty

1 Answer

I need a bleeding sequence for a 1994 GMC Suburban


The proper sequence to bleeding any brakes, are usually to do the one farthest away from the master cyl. first, and continue till ur at the last one. (left front). Rear brakes, then to the front brakes!

Jun 30, 2014 | 1994 Chevrolet Suburban

2 Answers

Xterra brakes


left front
right front
left rear
right rear

Apr 03, 2014 | 2001 Nissan Xterra

1 Answer

Whatside of the car is considered left rear?


The driver's side is the left side. As when you are facing the same way as the car is facing, or if you were sitting in the car: driver's is left side, passenger side is the right side of the vehicle.

Dec 31, 2012 | 1993 Chrysler New Yorker

1 Answer

1991 buick park avenue brake problems got bleed the brakes on the drivers side front and rear not a problem but the passenger side front cant get the air out keeps spitting fluid and have use a half b


If you have a manual for your vehicle, check how to bleed the system. Certain vehicles need to be bled in a certain order of sequence. If you are using a one man bleeding kit, when you don't see air bubbles in the clear tube but see only fluid, then it is bled properly.

Oct 28, 2011 | 1991 Buick Park Avenue

2 Answers

How do I bleed my brake lines on a 1999 Oldsmobile Bravada


This job is a lot easier with two people but you can do it with 1 if you have to. Have someone sit inside and pump the brakes 3 or 4 times and on the 4th pump hold it to the floor(all the way to the floor and don't let up at all). While they hold it to the floor you take a little end wrench and (Starting on driver side front going to pass. front next then pass. back and so on) you should already have the tire off before pumping brakes. On the caliper(the thing that holds the pads) there is a little bleeder nut Should be near where your brake line goes into the caliper. Now while they hold the pedal down you loosen that nut just a little bit and it should spit a little bit then maybe some fluid will come out maybe not on the first time but it does happen. Just dont leave it open longer than a couple seconds. Just long enough for air to escape then tighten back down. Repeat all those steps about 4 or 5 times for each tire or until brake pedal feels hard to push in. Make sure while your bleeding that you check your master cylinder often if you let it run out u will have to start over from the beginning. Also make sure who ever is holding the pedal do not let up when bleeder valve is open. Same thing. I just wantedn to m

Jan 09, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

If I remove a break line from one caliper for replacement, do I need to bleed the breaks on all four wheels or only the one that I have replaced the break line on?


When replacing any brake components it's always a great idea to bleed the brakes. Because your life depends on the serviceability of your brake system. When you open, crack or brake any line in your brake system, you automaticity introduce air into the system. Air can be compressed easily as opposed to brake fluid, which is designed not to compress as well as resist heat. The air in your system will cause your ABS and sensors to malfunction and or not work at all. When bleeding your brake system use this sequence start with: 1)right rear, 2)left rear, 3)front right, 4)front left. All vehicle parts and locations are referred to as the vehicle's left and right sides. Or as your setting in the drivers seat. Hope that helps.

Dec 21, 2010 | 2001 Lexus RX 300

5 Answers

Is there a bleeding sequence for a 1990 Toyota Four Runner? We replaced one front driver side brake line and both calipers and we cannot seem to get it to bleed properly. Thanks


normally, the brakes are bled starting from the furthest brake to the closest with respect to the master brake cylinder. the sequence is : right rear, left rear, right front, left front. pump the brakes until pressure is built up. do this rather slowly. while keeping downward pressure on the pedal, open the bleed screw slowly. the pedal will go to the floor. hold the pedal on the floor and tighten the bleed screw. do this until no air is observed. keep the reservoir. repeat with the rest of the brakes following in sequence

http://www.aa1car.com/library/2003/bf90347.htm

May 31, 2010 | 1990 Toyota 4Runner

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer


Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1993 Chrysler New Yorker Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...