Question about Lexus Cars & Trucks

Open Question

Where is the neutral safety switch located on 2002 lexus 300ES

How to replace neutral safety switch 2002 lexus 300ES

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Saaboheme
  • 76 Answers

SOURCE: 96' saab safety neutral switch

It is under the battery tray. Here is where it is and how to get to it.
Here is another procedural tutorial on how to remove and replace it.
Assuming that this is an automatic, the NSS is a common problem. A common, cheap and easy ten minute bypass method has been developed to get around the problem or at the least to use to confirm the diagnosis of a failed switch.

Posted on Dec 17, 2008

  • 1 Answer

SOURCE: 2004 Jeep Grand Chrokee Neutral Safety Switch Location

The switch is on the transmission..It is usually a dealer item but you can get one from Rockauto.com for about 1/4 of what the dealers charge.

Posted on May 25, 2009

emissionwiz
  • 75822 Answers

SOURCE: Neutral Safety Switch Location

on the transmission where the shift cable attaches.

Posted on Jun 15, 2009

ZJLimited
  • 17970 Answers

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Posted on Sep 18, 2009

  • 1 Answer

SOURCE: Neutral safety switch chevy silverado 02'

Hi Is a waterpump on a L300 4wd balt driven ?

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for neutral safety for a 2002 Lexus 430


The switch diagram is not published just the system it is part of.

Dec 02, 2016 | Lexus Cars & Trucks

1 Answer

How to replace neutral safety switch in 2002 pt cruiser


get a service manual from auto zone this will help you

Aug 29, 2012 | 2002 Chrysler PT Cruiser

1 Answer

Where is the neutral safety switch on 2002 nissan frontier


I have a 02 nissan frontier XE that needs the neutral safety switch replaced. I was able to locate it. However, its in a tight location and was wandering if anyone has changed it and the best approach to changing it....

Thanks a lot

Jan 05, 2012 | Cars & Trucks

1 Answer

Neurtral safety switch on 2002 pt cruiser


www.ptcruiserlinks.com/forum/tech-performance-forum/38859-wheres-park-neutral-switch-located-02-auto.html

Oct 25, 2011 | 2002 Chrysler PT Cruiser

1 Answer

I have lexus es 300, 2002. Yesterday after stopping at mall for 1 hr and came back to start the car, it does not start. No sound. Jump the battery still does not work. all lights are working. Is the...


It sounds like neutral safety switch (park/neutral issue) 1 question; Does the car have anti theft device? Same symptoms is anti thereof device is active.

Feb 19, 2011 | 2002 Lexus ES 300

1 Answer

Location of neutral safety switch on 2002 Chevrolet Venture, how to replace.


NEUTRAL SWITCH IS ON TOP OF TRANSMISSION.ITS ON THE MANUAL SHAFT . YOU NEED A HAYNES REPAIR MANAUL.IT WILL SHOW YOU HOW TO ADJUST NEUTRAL SWITCH WHEN REPLACING IT.YOU CAN GO TO ADVANCE AUTO OR OREILLY`S OR AUTO ZONE.TO BUY A REPAIR MANUAL.

Oct 03, 2009 | 2002 Chevrolet Venture Passanger

1 Answer

Location of NSS(neutral safety switch) on 2002 Dodge Caravan


It is in side the trans on top of the valve body. Why do you think you need to replace it?

Dec 16, 2008 | 2002 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...