Question about 2000 Honda Passport

Open Question

Bumper removal from 2000 Honda Passport

How to remove rear bumper

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: where is throttle position sensor located on 2000 honda passport

Normally attached at opposite end of throttle linkage. Remove your air cleaner intake hose at throttle body, and observe throttle plate that opens & closes as you press accelerator, it will be at the end of that, on outside of housing.

Posted on Jan 10, 2009

Ad
mrgreenz
  • 962 Answers

SOURCE: how can remove the starter of my honda passport 99

You have to drop the exhaust pipe and remove the wheel. I got his info from Wiki Answers hope it helps you.Read below.
. Disconnect the battery first. After that you may want to remove the driver's side front wheel. This gave us access to the starter for removal of the battery cable and the spade terminal which are on top of the starter while it is mounted. We then removed the two bolts that hold the starter in place. All of that took about 10 minutes to complete. On my passport the battery cable came off with a 12mm, the spade terminal is plug and play and all you have to do is push down on the tab on top and pull the terminal apart. The bolts for the starter are 14mm on my car. You need extensions to get at them though. After that is when all of the work began. We then tried every way possible to get it out of the compartment without taking anything else apart. No luck. So we removed the heat shields around the exhaust manifold and exhaust. Still not enough room. So finally we took the 3 bolts out of the flange that connects the exhaust manifold to the exhaust pipe. We had to use reverse torque bolt sockets for this. The one we used was the NAPA E-14. There are nuts on the bolts but removing only those won't do the trick. They are 17mm in case you are wondering. We then had to remove the bracket just aft (rearward) of the catalytic converter to get enough play in the exhaust pipe. Once you do this, the starter slides right out of the space moving down and aft. The new starter goes right in no problems once you are to this point. The only casualty to the whole process was one of the bolts from that flange on the exhaust manifold lost it's threads in the process. We were lucky that none of mine sheared off which is apparently a large concern and somewhat of a probability. Good luck

Posted on Jan 22, 2009

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

  • 2 Answers

SOURCE: problem removing rear wiper on 2006 honda pilot

You can't replace the wiper. But Parts department at any Honda dealer should sell the replacement blade (just the rubber part). I believe it was under $10. Good luck!

Posted on Aug 10, 2009

  • 564 Answers

SOURCE: cant remove the tail light assemblies on '09 accord sedan

youll have to pull up very firmly or it may have to slide to the side its held in place by a bodyfastener. a screw that fits into a slot. but i would try pulling up first.

Posted on Dec 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can l remove back door on my 1996 Honda passport door from inside.


How To Install Replace Fix Broken Rear Outside Door ...

? 9:52
https://www.youtube.com/watch?v=bUV6BZfVxDY
Jun 15, 2011 - Uploaded by 1A Auto Parts
1A Auto shows you how to repair, install, fix, change or replace a broken .... The outside door handle is broken on my HondaAccord and the child ... How To Install Replace Broken RearOutside Door Handle 1996-00 Honda ...

Can't open rear door - Car Forums and Automotive Chat - Automotive ...

www.automotiveforums.com > ... > Isuzu > Rodeo ' Passport ' MU
Can't open rear door Rodeo ' Passport ' MU Car Forums. ... The driver side rear door on my 95 Rodeo won't open. ... You can remove the door panel without opening the door. ... I've got a 96 Rodeo and the DS RR door was stuck as well. ... I went to aHonda dealer (lack of ISUZU dealers in my area) to get the part, it only ...

Oct 30, 2015 | 1996 Honda Passport

1 Answer

How to remove rear transmission seal from 2000 Isuzu Rodeo(Honda Passport)


the FSM covers this.
or if in USA< login to alldata.com and read.
its all there.

Jun 19, 2013 | 2000 Honda Passport

2 Answers

How do you remove a rear bumper


How To Install Replace Remove Rear Bumper Cover Honda Civic 01-05

Dec 11, 2010 | 2004 Honda Civic

2 Answers

I cant remove a rear axle seal to a 1999 honda passport


Axle bearing and seal are made together. It is pressed on axle.

Aug 18, 2009 | 1999 Honda Passport

1 Answer

Diagram for serpitine belt honda passport 2000


There should be a diagram on the front rail ..where you hood latches....unless someone has removed it...if it has been removed ..i'll try to find the diagram for it...i hope this helps...Keith

Jun 28, 2009 | 2000 Honda Passport

1 Answer

I WANT TO REMOVE THE FRONT BUMPER ON MY 2000 HONDA ACCORD


reach underneath bumper, you will see the post with screws on each post. Just remove the nuts on both sides, and bumper will come off.

Jun 09, 2009 | 1998 Honda Accord

1 Answer

How do you replace rear bumper cover on 2009 Honda Civic


Should look for the bumper shocks and remove which ever is easiest, remove bumper then remove cover , replace cover and reinstall bumper, watch out for wires and clips might hold cover to side plastic.

May 24, 2017 | 2009 Honda Civic

1 Answer

Where is throttle position sensor located on 2000 honda passport


Normally attached at opposite end of throttle linkage. Remove your air cleaner intake hose at throttle body, and observe throttle plate that opens & closes as you press accelerator, it will be at the end of that, on outside of housing.

Jan 10, 2009 | 1998 Honda Passport

1 Answer

Rear axle is bent


Go-To Car-Part.com
http://www.car-part.com/
Type the year (2000), and make (Honda Passport).
Search for Axle Assy Rear
Ignore 4x4 and focus at 4x2.
You must know the ratio - teeth (41/10 teeth, GT5) or (43/10 teeth, S7C)
(3.2L, 6 cyl, disc), 4x2 (drum brakes), 4.10 ratio (41/10 teeth, GT5)
(3.2L, 6 cyl, disc), 4x2 (drum brakes), 4.30 ratio (43/10 teeth, S7C)
1999 - 2002 Isuzu Rodeo - Honda Passport.
You can get an USED one for $600 plus shipping.
Good Luck.

Jan 04, 2009 | 2000 Honda Passport

Not finding what you are looking for?
2000 Honda Passport Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...