Question about Cars & Trucks

Open Question

I have a case 465 skid steer loader that the parking brakes will not release how do i fix this problem

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

erietrack
  • 37 Answers

SOURCE: parking brake release

When you try to release it, you'll need to pull the pedal up at the same time to get it back in place.

Posted on Nov 07, 2008

  • 548 Answers

SOURCE: Parking Brake on, Under dash release cable broken

Can you get to any part of the cable? If so, use a pair of pliers to release it until you can replace the cable.

Posted on Jan 25, 2009

  • 1 Answer

SOURCE: Parking Brake Alarm

inset the key and switch on to position 2
Scroll through the warning display untill you get the service indicator apears
Press and hold the reset button on the left of the dash apnel for about 4 mins
You will be asked if you want to reset
Press anh hold the reset button again until you hear an audible warning
It should now show the new interval to a service

Posted on Apr 06, 2009

  • 1348 Answers

SOURCE: Mustang parking brake won't release tension on rear brakes

since the new pads are alot thicker than the old ones,the brake needs to be set properly.
something is not right for sure.
the retainer for the park brake cable may be not in the right spot.there is two places it can fit.

Posted on May 23, 2009

  • 153 Answers

SOURCE: 2003 Honda Odyssey that will not come out Park

Yes most likely, the brake switch also sends power to a solenoid to unlock the shift lever. If the trans works fine once you get it out of park, the trans itself is fine

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2060 mustang skid steer loader hydraulic system not working engiune runs good.


I have only old skid loaders but when wiring a switch from wires being cut, just connect all the same color wires to each other. The wiring is color coded so it shouldn't be a problem there. As for the hydraulic system, don't run the engine with no hydraulic oil or you'll burn up the pump. It's happened to me and pump had to be replaced. Check the hydraulic oil for full.

Jun 15, 2017 | Cars & Trucks

1 Answer

How do I adjust creating on 1845c case skid steer


Cat® Skid Steer Loader ' Drive Chain Adjustment ... - YouTube

? 1:39
https://www.youtube.com/watch?v=FUtx88JifxY
Sep 27, 2011 - Uploaded by Cat® Products
Cat® Skid Steer Loader ' Drive Chain Adjustment & Chain Oil. Cat® Products ... Crane picking a skid steer out of a building. Unsafe - Duration: ...

How to change a drive chain on a case 90 XT - YouTube

? 2:27
https://www.youtube.com/watch?v=WBWVSpgZkKQ
Dec 27, 2014 - Uploaded by rayray haque
I made this video because I recently had to fix the drive chain on my skid steer. But there were no easily ...

Case 1845C Chain adjustment question - Heavy Equipment Forums

www.heavyequipmentforums.com/showthread.php?...Case-1845C...adju...

Mar 6, 2012 - 15 posts - ‎5 authors
I noticed it was making a popping noise in the front left wheel, so I. ... It appears that this skid steer is pretty much indestructible if taken care of ... Case 1845c Skid Steer Problem - Heavy Equipment Forums
11 posts
Apr 21, 2013
Case 1845C Uneven speed while travelling
5 posts
Nov 24, 2012
1845c what things go bad - Heavy Equipment Forums
15 posts
Jun 9, 2009
1845C Fan belt change question - Heavy Equipment ...
9 posts
Apr 9, 2009
More results from www.heavyequipmentforums.com

Dec 28, 2015 | Cars & Trucks

2 Answers

What is this for?


Button on theright apoears to be a thaction cintrol or anti skid conttrol.Button on the left could have something to do with parking brake release.

Mar 26, 2013 | Cars & Trucks

2 Answers

Good Morning, I have a 1996 Chevy S-10 Blazer that I used the parking brake on yesterday. However, when I went to use the hand parking release, it would not release the parking break and it felt like...


Yup! That is probably what is causing your dilema. To remove the lower panel, the parking brake release cable must be disconnected. It is not hard to reconnect if you know what you are looking for. The service manual does not provide a picture or I would post it for you. Anyway, it just "Snaps" into place on the parking brake pedal mechanizm. The cable just slips into a slot on the release lever. You can actually reach up and release the brake with your hand. (Be carefull not to get your fingers pinched when the pedal flies rearward) If you can get the pedal released by hand, then you have found the lever that the cable attaches to.

Feb 21, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

How to get the half shaft out


Halfshaft -sorry but the diagrams didn't paste into the fixya.com window, just the text. Also, this was for a 3.2L engine.
REMOVAL & INSTALLATION

  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Negative battery cable
    • Front wheel
    • Radiator skid plate
    • Transfer case skid plate
    • Brake calipers and mounting bracket
    • Brake rotor
    • Wheel speed sensor
    • Steering knuckle

  3. Support the axle housing with a jack. Unbolt the axle mounting bracket and
    remove the halfshaft/bracket assembly.
    To install:

  4. Install or connect the following:

    • Axle/bracket assembly. Tighten the bracket flange bolts to 85 ft. lbs. (116
      Nm) and the bracket mounting bolts to 112 ft. lbs. (152 Nm).
    • Steering knuckle
    • Wheel speed sensor
    • Brake rotor
    • Brake caliper and mounting bracket. Tighten the bracket bolts to 115 ft.
      lbs. (155 Nm).
    • Transfer case skid plate. Tighten the bolts to 27 ft. lbs. (37 Nm).
    • Radiator skid plate. Tighten the bolts to 58 ft. lbs. (78 Nm).
    • Front wheel
    • Negative battery cable

  5. Check the wheel alignment and adjust as necessary.





    Fig. 1: Exploded view of the left halfshaft, axle shaft and
    axle disconnect
    7924bg26.gif






    Fig. 2: Exploded view of the right halfshaft and mounting
    bracket
    9308bg03.gif



prev.gif next.gif

Oct 31, 2010 | 2002 Isuzu Rodeo Sport

2 Answers

What is abs how it function


ABS is anti-lock braking system. It is a range of four sensors which monitor the braking capability when you apply the brakes. If you are harsh and stamp on the brake pedal there is a risk of the wheels locking up and sliding (screeching from the tires).

The ABS sensors modulate the brake caliper pistons andapply and let go the brakes very quickly. This stops the tires from skidding and you will feel a pulse through the brake pedal as the hydraulic system is forced to release the pedal slightly for a fraction of a second.

As ABS stops your car from skidding it allows you to turn the steering when you are braking hard. This is good news for avoiding accidents. If you lock the wheels on a non ABS car, you continue in the direction of the wheels - unless you release the brakes and reapply quickly (same method as ABS) this is called cadence braking but when involved with a potential accident the last thing on people's minds is to release the brake pedal. Having only owned older cars, cadence braking is one method I've learned, especially from driving in the snow.

I hope this helps you and please vote for me :)

Jul 16, 2010 | 2005 Toyota ECHO

3 Answers

Right rear brake appears to be locked


Your rear brakes are not releasing. Make sure your brakes are fully released. Pull up and down on it a couple of times.Jack up the rear of the vehicle to get the tires of the surface and see if you can turn the wheels by hand. Brake cable may be bad. do this and post again

Dec 11, 2009 | 1992 Honda Civic

1 Answer

Automatic gearshift stuck in park


The release for the shifter is tied to the brake lites, check to see if the brake lights work, if they don't then test the brake light switch at the top of the brake pedal, if it lights a test lite when you press the brake it is ok, in that case you need to check the little solenoid that pulls the cable to unlock the shifter, it is bolted to the top of the steering column, in order to get at it you will have to unbolt the column and drop it dow.

Oct 09, 2008 | 2001 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...