Question about Cars & Trucks

1 Answer

I have 2004 Toyota camrey 2.4 se i have p0032 code

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 458 Answers

P0032"Heated O2 Sensor Circuit High Bank 1 Sensor 1" The ECU detected a high resistance condition in the heater element circuit for the pre-catalytic converter sensor.Probably just need to replace the sensor,but you can check for voltage across two of the wires(see your wiring diagram).

Posted on Dec 30, 2012

  • ed hawatmeh Dec 30, 2012

    i have replace the O2 Sensor and the mas Sensor and the catalic converter and the bottom and the light still on and every time i drive for 80 mil

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 973 Answers

SOURCE: check engine lite on pulls code p0032 2004 dodge

  • P0032 HO2S Heater Control Circuit High (Bank 1 Sensor 1)

  • Read the link here to solve your problem.

    Posted on Jun 01, 2010

    • 518 Answers

    SOURCE: What does code p0032 mean in a 2004 chrysler town

    Heater control circuit high, bank 1 sensor 1. Sounds like your O2 sensor in bank 1 in front of your convertor is bad.

    Posted on Sep 08, 2010

    ginko
    • 19396 Answers

    SOURCE: error code p0032 on 2004 dodge caravan. what is

    Hi.

    P0032 means HO2S Heater Control Circuit High (Bank 1 Sensor 1).

    It means high impedance from O2 sensor, check wiring to sensor and replace the sensor.
    Check O2 sensor located in bank 1 (cylinder 1 side- see here), and after the catalitic converter (there is also an O2 sensor before cat converter).

    Posted on Jul 31, 2010

    SOURCE: my gear shifter is stuck

    check the fuses if there good pump the brake and se if it comes out

    Posted on Oct 14, 2010

    • 5501 Answers

    SOURCE: 2004 pt cruiser keeps setting DTC's P0032 & P0038 ,sensors have been replaced with NTK

    Hello, First, you have to clear some of the Codes with a scanner or wait after 25-35 start-ups for the information to cycle out of the system.

    Next, make sure you have replaced the correct Bank or lower or upper sensor when there can be 4 sensors on the exhaust.

    The wiring running to your sensors may be bad. Also, if anyone has fooled with the wiring to the sensors, some have cooling tubes which are embedded in the wiring. Sometimes people rewire the connectors to fit different O2 sensor plug-ins and the cooling tube is cut. When these plug-ins are manipulated this way the sensors overheat.

    I can't say offhand about how your PT cruiser has its wires configured into junction connectors. They may be replaceable junctions or may be moulded into the housing of the O2 control unit as 1 piece.

    You will need to ask at an Autoparts store or go to a Salvage yard and try to find a harness you can use. It is not impossible that the sensors you purchased could be bad. You should be able to get some sort of continuity value from the prong connectors on the O2 sensors to see if you have a circuit in the part.

    I hope my solution is helpful, perhaps a Chrysler mechanic will answer you.

    Posted on Mar 04, 2012

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How to fix P0505 error code on toyota camrey


    disconnect the IAC plug. The IAC is a throttle bypass valve. Start the car . If the fault code doesnt reappear it is the IAC module. You may set other fault codes during the test they will disappear when you reconnect the IAC.
    If the code is still there is still there after disconnecting follow the wiring back to the PCM and check continuity at the connector

    May 29, 2014 | 1998 Toyota Camry

    1 Answer

    Mine is a P 0032 and P 0038


    upstream and downstream oxygen sensor heater voltages are too high, possible causes are
    - bad o2 sensors
    - shorted o2 wiring
    - bad pcm
    clear codes and determine if codes are hard(current)
    if they are, unplug sensors, clear codes and re-scan to see if p0032 and p0038 appear.(there will be 2 to 4 other codes generated)if p0032 and p0038 are gone from the list, change both o2 sensors.
    if p0032 and p0038 are still in the list, it is either wiring or pcm issue, use a meter to check for short from o2 connector to ground, with pcm unplugged..
    Good luck, Rob

    May 27, 2014 | Chrysler PT Cruiser Cars & Trucks

    1 Answer

    Error code p0032 on 2005 dodge grand caravan


    Hi there:

    P0032 - Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
    A P0032 DTC (diagnostic trouble code) refers to the O2 sensor (oxygen sensor) located on Bank 1 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2.



    This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. The sensor detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle's computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the O2 sensor. Essentially this P0032 code means that the resistance of the heater circuit is higher than normal. In some cases, that resistance level must be higher than 10 A to trigger the DTC code.


    Note, this code is very similar in nature to P0031, P0051, and P0052


    Potential Symptoms:
    Most likely you'll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.


    Causes: A P0032 DTC trouble code may be caused by one or more of the following:
    A short in the heater circuit in the sensor
    A failed O2 sensor heater
    Wiring/connectors broken/frayed leading to sensor and/or relay
    Failed PCM/ECM


    Possible Solutions: To fix a P0032 DTC code, you'll need to do a proper diagnosis. To do that, you'll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you'll want to check those as well. Use a digital volt ohm meter to:


    check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement)
    check the ground circuit for continuity
    measure the resistance of the heater circuit (done on the sensor itself)
    measure the resistance and voltage of the wiring
    Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is above 10 A.


    With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #2 on bank 1.


    Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There's also a chance that replacement parts for the P0032 code may also fall under a federal emissions warranty (check with your dealer to see if it's covered).


    Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

    Thank you for using FixYa, have a nice day.

    Jun 24, 2012 | Dodge Grand Caravan Cars & Trucks

    1 Answer

    Check engine light is on and it shows code P0032 on 2004 Dodge Grand Caravan 3.8 I think that is something on the O@ sensor, Can anyone point out where and how and if I have more than one O2...


    P0032 - Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
    A P0032 DTC (diagnostic trouble code) refers to the O2 sensor (oxygen sensor) located on Bank 1 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2.

    This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. The sensor detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle's computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the O2 sensor. Essentially this P0032 code means that the resistance of the heater circuit is higher than normal. In some cases, that resistance level must be higher than 10 A to trigger the DTC code.

    Note, this code is very similar in nature to P0031, P0051, and P0052

    Most likely you'll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.

    A P0032 DTC trouble code may be caused by one or more of the following:
    A short in the heater circuit in the sensor
    A failed O2 sensor heater
    Wiring/connectors broken/frayed leading to sensor and/or relay
    Failed PCM/ECM


    I hope this helps, abd just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment. Have a nice weekend and thanks for using FixYa.

    Jose.

    Oct 16, 2011 | 2004 Dodge Grand Caravan

    1 Answer

    Error code p0032 on town and country 3.8L engine. I replaced the bank1 oxygen sensor but still have the error code and check engine light is still on. installed brand new Bosch oxygen sensor. What else...


    Causes A P0032 DTC trouble code may be caused by one or more of the following:
    • A short in the heater circuit in the sensor
    • A failed O2 sensor heater
    • Wiring/connectors broken/frayed leading to sensor and/or relay
    • Failed PCM/ECM
    Possible Solutions To fix a P0032 DTC code, you'll need to do a proper diagnosis. To do that, you'll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you'll want to check those as well. Use a digital volt ohm meter to:
    • check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement)
    • check the ground circuit for continuity
    • measure the resistance of the heater circuit (done on the sensor itself)
    • measure the resistance and voltage of the wiring
    Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is above 10 A.
    With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #2 on bank 1.
    Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There's also a chance that replacement parts for the P0032 code may also fall under a federal emissions warranty (check with your dealer to see if it's covered).

    Jun 29, 2011 | 2004 Chrysler Town & Country

    1 Answer

    My gear shifter is stuck in park it is 1994 toyota camrey se


    check the fuses if there good pump the brake and se if it comes out

    Oct 14, 2010 | 1994 Toyota Camry

    2 Answers

    Error code p0032 on 2004 dodge caravan. what is the code?


    Hi.

    P0032 means HO2S Heater Control Circuit High (Bank 1 Sensor 1).

    It means high impedance from O2 sensor, check wiring to sensor and replace the sensor.
    Check O2 sensor located in bank 1 (cylinder 1 side- see here), and after the catalitic converter (there is also an O2 sensor before cat converter).

    Jul 31, 2010 | 2004 Dodge Caravan

    2 Answers

    2004 Toyota Camry Brakes


    Raise the vehicle up and remove the rims & tires

    Remove the brake pads, and then remove the calipers from the caliper retention brackets, do NOT remove the brake hoses from the calipers.

    Remove the caliper retaining brackets from the hub assemblies (2 large bolts on backside of the bracket)

    Tap the brake rotors off of the hubs, hit them from the back side of the rotor.

    No big mysteries here, this is a very easy job.

    Oct 21, 2008 | 2004 Toyota Camry

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    311 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...