Question about 2007 Ford Fusion I4 SEL Sedan

Open Question

2008 ford fusion light burned out in shifter center console

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: 2008 ford fusion alerts on dashboard

You can download a free owners manual from this site, it will identify all the dashboard alerts:

Posted on Aug 13, 2009

  • 55 Answers

SOURCE: stuck in park

the solenoid that releases it is bad or stuck from spilled drinks. try to put it in neutral with the key turned forward one click.

Posted on Oct 16, 2008

  • 424 Answers


You did not need to remove the heater box to replace the cable. There is a hole in the floor the cable passes through.

Posted on Nov 16, 2009

  • 2359 Answers

SOURCE: how to reset airbag light on 2008 ford fusion

Here's a quick check list for most common cost of SRS / Air bag problem.

Dirty contacts on driver and passenger seat belt buckles

Dirty contacts on seat belt connectors (under seats)

Dirty contacts on driver and passenger sides weight sensors (under seat)

Seat covers

Weight on passenger seat

(Example: grocery package trigger SRS / Air Bag light on the way home.)

I recommend you to pass an vacuum over the contacts and use CRC electronic parts cleaner to rule out connectivity2_bing.gif problem.

I DO NOT disconnecting the negative battery connector to clean the code(s)

Without the code(s) the dealer will takes "BILLABLE" time to reproduce the problem.


Please rate me answer if it is useful to you.



Posted on Dec 16, 2009

  • 18 Answers

SOURCE: Replacing console light for shifter selection

you have to remove the console from the car to get to the light. There are two retainers on either side of the console at the very front. push those in and the front will release. then you have to unscrew the rear of the console. two screws are located just below the rear cupholder on either side. the rear console should easily slide back and up. there are two screws exposed on the front console just in front of the emergency brake handle. remove those and you can remove the console. the gearshift lever must be in drive to clear the console. remove the screws holding the shift plate in place and the bulb is exposed

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace lights on shifter console of a 2008 hyundai sonata

Simple but time consuming . take the center console out and you will find some mini bulbs on the underside. Personnly is not worth the risk of breaking any plastic parts.

Feb 02, 2015 | 2008 Hyundai Sonata

1 Answer

Need bulb for 2008 ford escape center console

Need an owners manual for bulbs or have the lamp
out to read it's number

Apr 07, 2013 | 2008 Ford Escape

1 Answer


you will need to unscrew the center console

Sep 06, 2012 | 2008 Chevrolet Aveo

1 Answer

2008 ford fusion auxillary line in jack not working

how do you take centre console off for ford fusion because audio jack broken

Sep 04, 2012 | 2008 Ford Fusion

1 Answer

How to repair center console lights Shifter lights burned out how do i remove to replace bulbs

driver side of the shift console slide the driver seat back you will see an oval cover pry it out with a small screw driver look inside you will see a black electrical fitting with two blue wires use a long needle nose pliers to gently turn and lower the light fixture(black electrical fitting with two blue wires) pull out of the oval opening change the bulb and reverse the operation no console removal needed..

Oct 28, 2011 | 2008 Chevrolet Aveo

2 Answers

It will start but it stuck on park it's 2006 ford fusion

lawrence aud, You dont offer much detail but it sounds like you have a shift solenoid problem. This is a safety device that will not let you shift gears until you apply the brakes. Have someone check and see if you have brake lights. If not then you have to replace the brake light switch. The shift solenoid is also controlled by this switch. If this is the case, what you can do to move the vehicle is to disconnect the brake light switch and jump the wires with a piece of wire or a paper clip. This will allow you to move the vehicle but the brake lights will be on constantly. If you have brake lights then the shift solenoid itself is faulty. This can be found in the center console by the shifter if the shifter is on the floor between the seats. If shifter is on the cloumn then the solenoid is in the colunmn. Good luck with this.

May 17, 2011 | Ford Fusion Cars & Trucks

1 Answer

I have a 2006 ford fusion sel and the light bulb in center floor console is burned out. How do I change it?

You have to remove the cover around the gearshift, there you'll find the bulb, it's a small 12V bulb, just pull it out of the holder and install a new one.

May 20, 2010 | 2006 Ford Fusion

Not finding what you are looking for?
2007 Ford Fusion I4 SEL Sedan Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides