Question about Cars & Trucks

1 Answer

2000 sierra 5 spd removal

Is flex plate removal from clutch required...does not make sense

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

Do you mean flywheel removal? A flex plate is the toothed gear that bolts up to a torque converter on a vehicle with an automatic trans. If you mean a flywheel, which is what a clutch bolts up to, then yes it is highly recommended to remove it and have it surfaced when doing a clutch job. And since you are there anyway I would also suggest replacing the rear main seal

Posted on Dec 30, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 208 Answers

SOURCE: Removal of slave clutch master cylinder

The hydraulic cylinder is in the bell housing. When you separate the motor and tranny, you will see it as a unit with the throw-out bearing. Take the hydraulic line off before you start. You will have to bleed it when you are done.

Posted on Aug 13, 2008

motor1258
  • 6674 Answers

SOURCE: Need clutch diagram 2000 3.0 eclipse 5 spd

Click on link will get you there, scroll down side & click on blue and picture should appear for where you are.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801d6852

Posted on Jan 31, 2009

  • 100 Answers

SOURCE: 1989 mazda astina 323 5 spd manual clutch fluid??

Check the brake fluid resovoir, on the side there could be a hose coming off it part way down the side sharing the brake fluid to the clutch master cylinder

Posted on Sep 09, 2009

BCally1
  • 133 Answers

SOURCE: i have removed the pressure

theres an access cover under the turbo on the front of the bellhousing (2 10mm bolts) that you have to remove to access the bolts that hold the flywheel to the flexplate. kinda like removing the bolts to a torque converter. flywheel is real hevy though, watch your fingers

Posted on Sep 25, 2009

  • 11164 Answers

SOURCE: cant disconnect pushrod from clutch pedal to

have some push all the way down on the clutch than squeeze the plastic tabs on bushing to release u also need a special tool to remove disconnect the hydraulic line from clutch release cylinder most auto stores carry it or let u use /loan for free

Posted on Oct 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What causes damage flywheel on bmw is it common fault


-you mean broken teeth...? If so possibly crank the engine while it's still running.


Good Luck


Mai

Jan 07, 2016 | BMW X3 Series Cars & Trucks

2 Answers

I have a 1986 pontiac fiero 4 cyl. 5 spd . the clutch is moving fine , and so are the cables , but when you let the clutch out , nothing happens , the car does not move .


Does the pedal have "free play" at the top? Perhaps some adjustment is possible. If not, may be time to replace clutch disk.

Jan 14, 2015 | 1986 Pontiac Fiero

1 Answer

1990 7.3 idi auto non turbo fly wheel removal a replacement


An automatic doesn't have a flywheel, it has a flex plate instead. The torque converter makes it act a lot like a flywheel, though.

But... you're probably talking about the flex plate or the ring gear around its edge. This is going to require removing the engine from the vehicle - there's no other possible way to get the flex plate out.

Once the engine is sitting on the shop floor, it's a simple job to replace the flex plate - first you unbolt the torque converter and set it aside, then you unbolt the flex plate from the crankshaft. Bolt the new flex plate onto the crankshaft, bolt the torque converter to the new flex plate, and put the engine back into the vehicle.

Jul 30, 2014 | Cars & Trucks

1 Answer

How to replace a flywheel on a ford five hundred


Remove the inspection plate and undo the bolts attaching the torque converter to the flex plate Remove transmission If you are not familiar with that procedure give the job to a mechanic. Remove the clutch if not auto again know how to replace clutch pressure plate and clutch plate. Something tells me that the flywheel isn't stripped but the flexiplate has fractured as it is unusual for the teeth of the ring gear to be completely stripped. Moving on use an impact gun to undo the bolts holding on the flywheel/flex plate Installation is reverse to removal. But I recommend you have good advice handy to do this job

PLEASE RATE THIS REPLY FOR ACCURACY

Mar 23, 2013 | 2007 Ford Five Hundred Limited Sedan

2 Answers

I have a 96 cavalier 2.2 5 spd


the pressure plate might have gone bad or need resurfacing if glazed.
also the flywheel could be glazed.

Jan 30, 2013 | Chevrolet Cavalier Cars & Trucks

1 Answer

Kia Sephia 5 spd won't shift gears


You need to bleed the lines with a special tool, contact the dealer on this.

Jun 13, 2012 | 2000 Kia Sephia

1 Answer

What year/model transmissions will fit a 1989 GMC sierra, 2500, 350 engine, 2-wheel drive? Thanks


A.T., VIN model "C" (4x2), TH400, 6 cyl
A.T., VIN model "C" (4x2), TH400, 8 cyl, 8-305 (5.0L)
}A}}400}466495" type="radio" name="userInterchange" />A.T., VIN model "C" (4x2), TH400, 8 cyl, 8-350 (5.7L)
}A}}400}466496" type="radio" name="userInterchange" />A.T., VIN model "C" (4x2), TH400, 8 cyl, 8-379 (6.2L, diesel)
E>}B}}400}466497" type="radio" name="userInterchange" />A.T., VIN model "C" (4x2), TH700, diesel
A.T., VIN model "K" (4x4), TH400, 6 cyl
B@}}}400}466499" type="radio" name="userInterchange" />A.T., VIN model "K" (4x4), TH400, 8 cyl, diesel
A.T., VIN model "K" (4x4), TH400, 8 cyl, gasoline
A.T., VIN model "K" (4x4), TH700, diesel
FFC}B}}400}466502" type="radio" name="userInterchange" />M.T., 4 spd, 4x2, VIN model "C"
FFC}A}}400}466503" type="radio" name="userInterchange" />M.T., 4 spd, 4x2, VIN model "R"
ECB}B}}400}466504" type="radio" name="userInterchange" />M.T., 4 spd, 4x4, (VIN model "K")
M.T., 5 spd, 4x2
M.T., 5 spd, 4x4
A.T., VIN model "C" (4x2), TH700, gasoline
F=A}B}}400}466508" type="radio" name="userInterchange" />A.T., VIN model "K" (4x4), TH700, gasoline
}B}}400}466509" type="radio" name="userInterchange" />A.T., VIN model "R" (4x2)

Jan 14, 2011 | 1989 GMC Sierra

2 Answers

Is there a remedy for a low clutch engagement on my '98, 2.5L, 5 spd Cherokee? It has 156k miles and I do not know its history ...


Check the clutch master cylinder for leaks, especially where the rod goes into it from under the dash. check the line to the slave unit for leaks, check the slave for leaks (if your slave is part of the throwout bearing and is inside the bellhousing, look for fluid driping from the bottom of the housing). If that checks out OK, try having someone push down on the pedal and open the bleed fitting on the slave, to remove any air from the system. If there is no air, likely there is a problem with the clutch itself. (worn out disc or pressure plate spring)

Oct 21, 2009 | 2000 Jeep Cherokee

2 Answers

High rpms but no pick up


You need a new clutch. Don't wait long or you will bur surface of flywheel

Mar 27, 2009 | 1996 Volvo 850

1 Answer

Transmission noise - 93 Honda del Sol w/ 5-spd manual trans.


Imput shaft bearing. It just happened to me. You're looking at a $400 fix.

Mar 22, 2009 | 1994 Honda Civic Del Sol

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...