Question about 2004 Chevrolet Suburban

Open Question

Where is the egr valve on a 2004 1500 surburban located and is it electric or vacuum

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: vacuum to the egr valve on my 89 chevy van with 3o5

Stuck closed. You can't free these up. Gotta buy a new one.

Posted on Feb 13, 2009

drsinister69
  • 2317 Answers

SOURCE: 95 cavalier changed EGR vacuum sensor and EGR

Check for vacuum leaks. Use a can of GumOut to spray around vacuum hoses, while the motor is running, if the idle increases when sprayed on or around a certain hose, check that hose for leaks.

Posted on Mar 06, 2010

  • 2002 Answers

SOURCE: I have a 1979 El

There should be a vacuum diagram under the hood but if it's gone the EGR hooks to the purple topped vacum port. I think that's the one on the thermostat housing, if I remember right. The other vacuum port should have a red and white restrictor valve in one of the lines and that is the wrong one. The other line from it goes to the bottom left on the carburator. If you don't have any of that stuff, and that's possible, then it needs to have manifold vacuum so hook it direct to the carb or the manifold on an available nipple. Hope this helps.

Posted on Apr 12, 2011

emissionwiz
  • 75807 Answers

SOURCE: avalanche 2007 where is the egr valve location

Rear right hand side of engine compartment

Posted on Aug 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the egr solenoid located


EGR vacuum solenoid is located below your EGR valve. Center your self on the engine, look between the rear of the engine and your firewall. You can see your the top of you EGR valve, there will be a small vacuum hose connected to the top. Follow that small hose straight down from your EGR valve and it connects to the solenoid. You can see the solenoid better from beneath the car. May have an orange connector. Hope this helps.

Feb 07, 2012 | 2000 Mitsubishi Eclipse

1 Answer

I have a 1995 gmc jimmy. Fuel injected 4.3 vortec. I need to clean out the egr valve but I have not been able to locate it. Can some one please help! If you have photos that would really help


Sorry I dont have a pic. for you. But here are instructions. The EGR valve is located at the top right of the engine next to the throttle body. REMOVAL & INSTALLATION
Except Linear EGR Valve

Disconnect the negative battery cable.
Remove the air cleaner assembly from the engine.
If equipped, unplug the valve electrical connection.
Remove the EGR valve vacuum tube from the valve.
Remove the EGR bolts and/or nuts and remove the EGR valve and gasket.
To install:
Install a new gasket to the EGR valve and install the EGR valve to the manifold.
Install the nuts and/or bolts. Tighten the bolts to 17 ft. lbs. (24 Nm) and the nuts to 15 ft. lbs. (20 Nm).
Connect the vacuum tube to the EGR valve.
If equipped, attach the valve electrical connection.
Install the air cleaner and connect the negative battery cable.
Linear EGR Valve
Disconnect the negative battery cable.
Note the position of the EGR valve prior to removal. Do not rotate the valve 180?.
Unplug the valve electrical connection..
Unfasten the valve retainers, then remove the valve and the gasket.

To install:
Clean all gasket residue from the gasket mating surfaces.
Install a new gasket and the valve.
Install the valve retainers.
On 1994-97 2.2L engines and 1994-95 4.3L engines, tighten the valve retainers to 17 ft. lbs. (24 Nm). On 1998-99 2.2L models, tighten the retainers to 19 ft. lbs. (26 Nm).
On 1996-99 4.3L models, tighten the retainers on the first pass to 89 inch lbs. (10 Nm) and on the final pass to 18 ft. lbs. (25 Nm).
Attach the valve electrical connections and connect the negative battery cable.

Nov 28, 2011 | 1995 GMC Jimmy

1 Answer

1987 Chevy S-10 Throttle Body 2.8, Where does the Vacuum Line from the EGR Valve go to?


It should go to a vacuum switch that controls the EGR valve. Not sure of location usually on intake manifold. will have two vacuum lines and electrical wires that plug in.

Feb 08, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

PO401 EGR , the ECM has detected too little flow


The EGR valve is towards the firewall and looks like a flying saucer with either a vacuum hose or electrical connectors attached to it.EGR stands for exhaust gas regulator. So this item has to be connected to your exhaust manifold. During engine operations in order to cool off combustion temperatures this valve opens and permits exhaust gases into combustion chamber.
Your code is saying that its passage way is clogged ,the valve is either stuck closed ,the vacuum or electrical system that control it are defective. I recommend you get the repair manual for this vehicle there are several types of EGR valves and the testing procedure are different for each one. If your good with a voltmeter than getting the manual for this vehicle is gonna save you a fortune.
The easiest thing to do when you locate the valve is to remove it, use gun out and spray the passage way it sits on . Then clean the valve itself. If it has a vacuum port hook it up to a vacuum pump and see if it holds vacuum ( about 3-5 hg's) and its pintel moves. if it does than valve is ok. Then replace gasket and install valve. If valve has electrical connectors then clean passage and valve replace gasket and install valve.Your gonna have to go to Autozone again to have them erase code before you know for sure you repaired the item. Good luck

May 19, 2010 | 1998 Ford Taurus

1 Answer

Random missfire all cylinders 1996 honda civic sohc


Check the EGR valve system. Honda's are prone to the exhaust supply to the EGR valve getting clogged with carbon at the valve port entrance. A clogged EGR valve can cause the engine combustion temperature to climb and then for pre-ignition miss-fire events to become common. The EGR is located inside the elbow of the air filter pipe at the back of the engine on the left beneath the coil. Anything you can temporarily remove to provide access the better. The EGR valve has two bolts, an electrical connector and a vacuum line attached to its top. Take it off and give it a really good clean, carburettor or brake cleaner works well in conjunction with cloths and brushes. Once cleaned like new replace everything including the vacuum line and electrical connector.

May 09, 2010 | 1998 Honda Civic

1 Answer

How do you replace the egr valve in a 1997 chrysler concorde lx


Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing
  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Sep 04, 2009 | 1997 Chrysler Concorde

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

1 Answer

No vacuum to egr valve


there is an EGR vacuum solenoid somwhere that controls on/off vacuum to actuate the valve. i am not to sure of the location, but follow the vacuum line back from the egr until you find a device that looks like an electrical check valve for vacuum. that is a possibilty. but then again i am a ford,chrysler guy and am just giving you an answer based on my understanding of the functuality of a vacuum egr system

Jan 15, 2009 | 1997 Nissan Pickup

2 Answers

EGR VALVE ON 96 FORD PROBE SE


If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
I have to junk my 1996 Probe if I don't find them - Missouri emissions.

Aug 24, 2008 | 1996 Ford Probe

1 Answer

How do you replace egr valve in a 2005 dodge caravan


REMOVAL - 2.4L The EGR valve and Electrical EGR Transducer are serviced as an assembly.
  1. Disconnect vacuum tube from electric EGR transducer. Inspect vacuum tube for damage.
  2. Remove electrical connector from solenoid.
  3. Remove EGR tube bolts from EGR valve.
  4. Remove EGR valve from cylinder head adaptor.
  5. Clean gasket surface and discard old gasket. Check for any signs of leakage or cracked surfaces. Repair or replace as necessary

INSTALLATION - 2.4L The EGR valve and Electrical EGR Transducer are serviced as an assembly.
  1. Assemble EGR valve with new gasket onto the cylinder head adaptor.
  2. Loose assemble the bolts from EGR valve to EGR tube.
  3. Loose assemble the bolts from EGR valve to cylinder head.
  4. Tighten bolts from EGR valve to cylinder head to 22.8 N·m (200 ±25 in. lbs.) torque.
  5. Tighten bolts from EGR valve to EGR tube to 11.9 N·m (105 ±20 in. lbs.) torque.
  6. Reconnect vacuum hose and electrical connector to electrical EGR transducer.

Aug 03, 2008 | 2007 Dodge Caravan SXT Minivan New Cars

Not finding what you are looking for?
2004 Chevrolet Suburban Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...