Question about 1997 Ford F350 Crew Cab

Open Question

Ford f350 7.5l dually crank no start just replaced fuel pump

Just replaced fuel pump and starter new spark plug wires new spark plugs new battery it will crank but it wont start why?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 65 Answers

SOURCE: Ford Escort 1998 fuel pump not working.

good old ford lol, try looking at the crank sensor its located at the front of the engine tucked in right hand side of exhaust manifold and gearbox, two pin plug, i have also known these to have no end of faults with the fusebox.
easy to remove, and solder the connections inside they all suffer eventually, if your not to handy with cars i recommend taking to a auto electrician, easy if you know how. Good luck Davelee

Posted on Mar 24, 2009

Ad
  • 66 Answers

SOURCE: MY 2001 FORD TAURUS DOHC WILL NOT START IT CRANKS

i would look at the fuel shut down switch .....make sure that it is pushed in most likely your problem

Posted on Nov 30, 2009

  • 5522 Answers

SOURCE: 2001 ford focus will not start. The engine will

I will try to help you. You are correct about the starting fluid, if it has fire starting fluid should do something. So the problem must be either no fire to the plugs or the timing belt is broke.

Check to see if the plugs have spark. If they do not, then get with the Autoparts store and ask if your car needs a Ignition relay to run. Then ask if your car takes a rubber timing belt. If your car does not have a rubber timing belt try the Ignition relay. If you do have a rubber belt check behind the shield in front of the engine to see if the timing belt is broke.

The timing belt is different than the serpetine belt that drives the pulleys. Cars with rubber timing belts have both belts. Should your timing belt be broken it is not an expensive repair. But you will need to details on replacement of that part.

Posted on Apr 18, 2010

Testimonial: "I appreciate your help and will be checking your sugestion very soon."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the alternator starter and battery and my 1999 ford contour still won't crank we even have tried jumping it


Doe's it try to start, make the sound of the engine turning over, but just does not fire up?
If it "turns over", then next you carefully pull the spark plug boot off of one of the spark plug remove the spark plug, plug the wire back on to the plug, lay it so that you can see the end of the spark plug and try to crank it, if you see the spark at the end of the plug that means your getting electricity "fire" to the plug.
Next step is fuel. The fuel filter, being that it's a 1999 may be stopping that. or maybe fuel pump.

Jul 05, 2015 | Ford Cars & Trucks

2 Answers

Feul problem


Lots of things could cause a no-start, Hendrik. Is your "Check Engine" light on? If so, please have someone get the OBD error codes from the car's computer.

Does it crank but not fire?

If it doesn't crank, check the battery condition, battery connections, ground connections to frame and engine block, starter solenoid, starter motor.

If it cranks, doublecheck your fuel pump installation. Make sure the new fuel pump is properly connected and properly electrically grounded. Look for a fuel pump fuse. Check for proper fuel pressure at the fuel rail, check the fuel flow rate. Check for spark, check or replace spark plugs, distributor cap, rotor, plug wires. Check valve timing, replace timing belt or chain if necessary. Check compression.

Aug 03, 2014 | 2001 Kia Sportage

1 Answer

My '97 ford taurus isnt kicking over while tryn to start it up


Anything done to car, or happened recently that might affect this?
If starter fluid doesn't work, and starter is cranking normally (too fast may point to a timing belt broke, too slow may mean battery run down and not producing sufficient spark), there's still a problem in your ignition. Pull a sparkplug or two. After cranking a little they should be wet with gas. Check for compression while a plug is out: hold your finger over plug hole when cranking. You should feel pressure buildup and release over and over as long as cranking.
A properly timed engine needs spark, fuel, and compression to start. Keep reviewing your procedure. Something is not right.
You may want to have the computer scanned for possible trouble codes. Check plug wires for proper routing. Were plugs gapped right?

Nov 30, 2011 | 1997 Ford Taurus

2 Answers

Car turns over but will not start changed the coil and still wont start


There are some possibilities which you will have to check in this case:--

1) First of all check the power and voltage to the battery. With meter it will show exact 12 volt if the battery is charged. If the voltage is less get the battery charged at local auto repair shop. If the battery is internally drained and not getting charged then its time to replace the battery.

2) When you crank the car do you see spark coming at the spark plug? If no then its time to check the spark plugs and coil pack. If the spark plugs are not worn out and looks new then its time to check coil pack. The spark plug gets power to spark from coil pack.

3) The other thing to check in this case is the starter solenoid of the car. If the battery is charged and you start the car then it gives power to the starter to start the car. But if starter is faulty or not connected properly then car will not start.

4) The other thing to check in this case is fuel in the car. If there is fuel in the car then check the blockages in the fuel pump if the fuel pump looks proper then check the fuel filter above the fuel pump.

5) If all the above possibilities mentioned above checked out OK/perfect then it's a electrical issue and the wiring's in the car needs to be checked. The car gets power from the battery to get started. so the wires from battery needs to be checked one by one.

-------------


Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Sep 25, 2010 | 1995 Ford Contour

1 Answer

My '93 F250 5.8 l Automatic was turning over slowly when cranking to start. Replaced battery no change; Then after sitting for 2 mo. turning key to start produced only a click and dead gauges (battery...


The battery to starter connection has power.the battery is ok.but there are many other possibilities related to battery and its other connections,the spark plugs,the fuel pump,the fuel itself,the sensors(o2 sensor,maf sensor)the valve(IAC valve,egr valve). Most probably the spark plug,the coil pack and crank shaft sensor.This 3 are not getting power to get the car start.

There are some possibilities which you will have to check in this case:--

1) First of all check the power and voltage to the battery. With meter it will show exact 12 volt if the battery is charged. If the voltage is less get the battery charged at local auto repair shop. If the battery is internally drained and not getting charged then its time to replace the battery.

2) When you crank the car do you see spark coming at the spark plug? If no then its time to check the spark plugs and coil pack. If the spark plugs are not worn out and looks new then its time to check coil pack. The spark plug gets power to spark from coil pack.

3) The other thing to check in this case is the starter solenoid of the car. If the battery is charged and you start the car then it gives power to the starter to start the car. But if starter is faulty or not connected properly then car will not start.

4) The other thing to check in this case is fuel in the car. If there is fuel in the car then check the blockages in the fuel pump if the fuel pump looks proper then check the fuel filter above the fuel pump.

5) If all the above possibilities mentioned above checked out OK/perfect then it's a electrical issue and the wiring's in the car needs to be checked. The car gets power from the battery to get started. so the wires from battery needs to be checked one by one.



Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Sep 20, 2010 | 1993 Ford F250

1 Answer

Wont start even if i push her,toyota tercel has no spark


So your telling me that this car is a stick and you can't pop the clutch to start it ? Correct?
I'm gonna give you a list of thing to check, good luck.

a)Do you have crank no start? (see entire write up)
b)No crank no start?, ( battery, battery cables, ignition switch,,starter relay)
c)No dash lights, no crank? (battery, battery cables ignition switch)
If you have symptom A then the affected items are , ignition switch, battery, battery cables, starter, starter relay ,coil, coil pack, ignition module ,Distributor cap ,rotor, (if applicable) spark plugs and wires.
The best thing to do is to first make sure your timing belt didn't break. As long as the engine cranks you can do this. Give the battery a 3 min charge . Then have a helper crank the vehicle while you observe the rotation of all the pulley's and belts. They must rotate together. If the vehicle has a distributor remove the cap ground the coil wire and watch the rotor as the engine is cranked. it should spin. If this is a-ok your worse nightmare is over.
Now we have eliminated the timing belt as being a cause. We now have to charged the battery again for three min and load test it( this is best done by a repair shop a load tester is expensive .If the battery if more than 5yrs old you may want to replace it.
If battery does not pass load test replace it.
Whatever you decide the rest of the items can NOT be checked out without a fully charged battery.
Check ignition switch and starter relay for B+ going to them and leaving them. Check starter circuit. Make sure B+ is making it to starter ( use a digital voltmeter). If B+ (12 volts) is making it to the starter and it doesn't crank then the starter is defective. Do a starter current draw test to verify this or remove the starter and have it bench tested.
If starter cranks now your into coil testing .
Pull a spark plug hook it up to a spark tester and ground it, now crank the engine if you get spark coil is ok and in all likelihood so is module.
If you don't get spark test for spark at the coil wire.
If you get spark here and don't get it at the spark plug wire problem is at distributor cap , rotor or spark plug wire. If plugs look bad use a fresh plug to do testing and naturally replace them.
If all of the above are a-ok.
Next is fuel checks.
Easiest fuel check is to put key into ignition cylinder and turn to on position. Lister for pump to buzz or hum. if it doesn't then check fuel pump relay for B+ going to it and leaving it and going to the pump. If B+ making it to pump and it doesn't turn on the pump is your problem. If B+ not making it to pump either the relay or the ignition switch is defective.
Naturally if the pump is defective have a repair shop do the repair . Its dangerous and a real pain.
Good Luck
IN YOUR CASE I BELIEVE YOU NEED A NEW BATTERY UNLESS THIS ONE IS FAIRLY NEW.

Apr 29, 2010 | 1995 Toyota Tercel

1 Answer

I have a 1999 dodge durango,i replaced new spark plugs and new wires but the car won't start?


Do you have crank no start? (see entire write up)
b)No crank no start?, ( battery, battery cables, neutral safety switch ignition switch,,starter relay)
c)No dash lights, no crank? (battery, battery cables, ignition switch)
If you have symptom A then the affected items are , ignition switch, battery, battery cables, starter, starter relay ,coil, coil pack, ignition module ,Distributor cap ,rotor, (if applicable) spark plugs and wires.
The best thing to do is to first make sure your timing belt didn't break. As long as the engine cranks you can do this. Give the battery a 3 min charge . Then have a helper crank the vehicle while you observe the rotation of all the pulley's and belts. They must rotate together. If the vehicle has a distributor remove the cap ground the coil wire and watch the rotor as the engine is cranked. it should spin. If this is a-ok your worse nightmare is over.
Now we have eliminated the timing belt as being a cause. We now have to charge the battery again for three min and load test it( this is best done by a repair shop a load tester is expensive .If the battery is more than 5yrs old you may want to replace it.
If battery does not pass load test replace it.
Whatever you decide the rest of the items can NOT be checked out without a fully charged battery.
Check ignition switch and starter relay for B+ going to them and leaving them. Check starter circuit.Do not forget neutral safety switch its on your brake pedal and once depressed it closes the circuit to the relay so B+ can travel to it . Make sure B+ is making it to starter ( use a digital voltmeter). If B+ (12 volts) is making it to the starter and it doesn't crank then the starter is defective. Do a starter current draw test to verify this or remove the starter and have it bench tested.
If starter cranks now your into coil testing .
Pull a spark plug hook it up to a spark tester and ground it, now crank the engine if you get spark coil is ok and in all likelihood so is module.
If you don't get spark test for spark at the coil wire.
If you get spark here and don't get it at the spark plug wire problem is at distributor cap , rotor or spark plug wire. IN YOUR CASE YOU HAVE NEW PLUGS AND WIRES SO IT WILL BE EASIER TO CHECK FOR SPARK.If all of the above are a-ok.
Next is fuel checks.
Easiest fuel check is to put key into ignition cylinder and turn to on position. Lister for pump to buzz or hum. if it doesn't then check fuel pump relay for B+ going to it and leaving it and going to the pump. If B+ making it to pump and it doesn't turn on the pump is your problem. If B+ not making it to pump either the relay or the ignition switch is defective.
Naturally if the pump is defective have a repair shop do the repair .THERE ARE FUEL PRESSURE AND VOLUME TESTS DONE TO VERIFY IF PUMP IS DEFECTIVE OR NOT. IF WITH THE TESTING PROCEDURES I'VE GIVEN YOUYOU CAN NOT DETERMINE WHETHER THE PUMP IS DEFECTIVE HAVE A REPAIR SHOP DO FURTHER TESTING ON THE PUMP. THESE TESTS ARE A LITTLE DANGEROUS and a real pain.
Good Luck

Apr 29, 2010 | 1999 Dodge Durango

2 Answers

Wont start turns over but no start


1 Inspect Battery Battery Discharged or Faulty. 2 Inspect Battery Cable Corroded, Broken, Shorted or Poorly Connected Battery Cable. 3 Inspect Fuel Filter Clogged or Dirty Fuel Filter. 3 Inspect Distributor Cap Distributor Cap Cracked or Burned. 5 Inspect Coil - Ignition Faulty Ignition Coil. 6 Inspect Wireset Worn, Damaged or Faulty Spark Plug Wire(s). 7 Inspect Spark Plug Incorrectly Gapped or Fouled Spark Plug(s). 8 Inspect Starter Starter Motor Faulty. 9 Inspect Fuel Pump Low Fuel Pressure. 10 Inspect Solenoid Switch Faulty Starter Solenoid Switch. 11 Inspect Relay - Fuel Pumpat Faulty Fuel Pump Relay. 12 Inspect Fuel Injector Pressure Regulator Faulty Fuel Injector Pressure Regulator. 13 Inspect Ignition Switch Improperly Connected or Faulty Ignition Switch. 14 Inspect Starter Drive Faulty Starter Drive. 15 Inspect Fuel Injector Dirty or Worn Fuel Injectors. 16 Inspect Fuel Pump Strainer Clogged or Dirty Fuel Pump Strainerat. 17 Inspect Engine Control Computer Incorrect Operating Information Being Delivered and Sent From The EEC. 18 Inspect Fuel Tank Fuel Tank Empty. 19 Inspect Carburetor Carburetor Flooded or Faulty Choke. 20 Inspect Distributor Worn, Loose, or Incorrectly Installed Distributor.

Jul 02, 2009 | 1997 Ford F250 SuperCab

1 Answer

2004 Kia Sedona wont start but i can hear starter.


if the starter is revving very slowly it is the battery, charge battery. if not, It can be three things happing. 1 no spark 2 no fuel 3 no crank signal or the car computer is bad- you will need to unplug one of the spark wires and remove the spark plug and put the spark plug in the spark plug wire boot, and touch the spark plug on any metal on the car and have some start the car. donot touch the spark plug itself and see if there is a spark. if spark is bright, then it is not spark plug and wires but if no or spark is not bright, check the spark plug wires by applying a little bit of water on the spark plug wire and take a 12v test light, connect the clap to ground and and have some one to crank the vehicle, touch allover the spark plug wires with the tip of the test light, if you see spark, replace the wires and change the plugs.. they are not good. if spark is present, check for fuel by removing any one of the spark plugs and see if it is wet. if wet fuel pump is ok but if not go look for the fuel pump fuse and relay. is fuse blown, replace, check the relay resistor with a volt meter. it should be around 40 to 80 ohm. if everything is good from this point check the fuel pump itself by disconnecting the connector to the pump and apply 12v and ground using jumper wires or some wires to the fuel pump if you donot hear the pump,replace pump. if you, the crank signal or computer may be the problem

Jan 02, 2009 | 2004 Kia Sedona

Not finding what you are looking for?
1997 Ford F350 Crew Cab Logo

Related Topics:

676 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...