Question about 2010 Toyota Tundra

Open Question

2010 Toyota tundra console removal

How to remove the center console

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Opelmanz
  • 62 Answers

SOURCE: door panel toyota

three steps.

1. locate screw holes for door handle (and other areas maybe) and remove. the screws may be located behind plugs that you remove with small flat screw driver
2. disconnect and remove power lock/window unit, usually pries up from one end (rear of car) and slides out. be careful not to stracth leather or upholstry
3. using screwdriver, pry bar, nail bar or other flat piece of metal pry panel away from door one clip at a time. try to pry near the clip, otherwise you risk damaging the panel's interior

post another problem if you get further and still have trouble.

paul

Posted on Oct 26, 2008

  • 1861 Answers

SOURCE: toyota tundra 2008 removal radio

There is a hidden screw under the center knob on the heater control. Remove this, and the other 2 srews hidden in the corners of the air registers.

Posted on Oct 08, 2009

  • 740 Answers

SOURCE: My daughter dropped an ear ring thru the handbrake

there should be two screws up at the front and a few in the conole undert the rubber mat looking piece in the console

Posted on Mar 14, 2010

  • 1403 Answers

SOURCE: the interior hood release isnt

try this,have another person push down on the hood in the front of your truck,while they apply downward pressure,pull hood release out,keep the hood release pressure pulled out,tell the other person to let up on hood,then release the pressure you have on the hood release handle and hood should pop up.if this does'nt work,you have a broken hood release cable.that means you'll have to get on the ground under front of truck and reach up to the hood release cable with pliers and pull the cable release manually.good luck hope this helps and thank you for choosing fixya.com

Posted on Jan 10, 2011

KAComstock
  • 274 Answers

SOURCE: I need to replace starter

No you do not need to remove the plenums. The starter is removed and installed from underneath the truck of from within the wheel well if the wheel is removed. You should go buy a Haynes or Chilton repair manual for $20 they are indisposable to do it yourselfers and will give detailed step-by-step instructions with pictures.

Posted on May 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Recalls on 2010 tundra


Go in on auto recalls on the net..or put in the search window 2010 tundra recalls You Will find what you are looking for..good luck

Oct 22, 2014 | 2010 Toyota Tundra

Tip

Toyota January and February recall


Here are the models affected by the Toyota recall


• 2009-2010 RAV4
• 2009-2010 Corolla
• 2009-2010 Matrix
• 2005-2010 Avalon
• 2007-2010 Camry
• 2010 Highlander
• 2007-2010 Tundra
• 2008-2010 Sequoia

This the gas pedal issue if you have one of those cars it's important to contact your Toyota dealer

on Feb 05, 2010 | Toyota Avalon Cars & Trucks

1 Answer

Is there a recall on 2010 tundra


Go in on the net and put in recalls for 2010 Toyota Tundra it will be there..in detail..good luck

Oct 22, 2014 | 2010 Toyota Tundra

1 Answer

Want to now how to remove front rotors on a 2010 4wd toyota tundra


Here is a video i found on youtube that explains how to replace a front rotor on a Toyota Tundra how ever this is for a older model of tundra.
With my knowledge of working on cars and trucks the same process usually applys to almost all vehicles for rotor replacements i hope this helps,
http://www.youtube.com/watch?v=YpH8LVcAlxw

Feb 16, 2013 | Toyota Pickup Cars & Trucks

1 Answer

Removing front rotors


Here is a video i found on youtube that explains how to replace a front rotor on a Toyota Tundra how ever this is for a older model of tundra.
With my knowledge of working on cars and trucks the same process usually applys to almost all vehicles for rotor replacements i hope this helps,
http://www.youtube.com/watch?v=YpH8LVcAlxw

Feb 16, 2013 | Toyota Pickup Cars & Trucks

1 Answer

Blower motor


Blower motors can be bears to get out. Many times, simply removing the glove box will give you enough room to get it out from underneath the dashboard. Other times, you have to remove the dashboard. This is not so easy due to the crash sensors and electronics in modern vehicles. I suggest you buy the Haynes manual for your car, it is well worth it. You will need a friend to help you pull it out over the steering column - should it come to that.

Sep 25, 2012 | 2010 Toyota Tundra

1 Answer

2010 honda pilot center console removal due to vibration underneath


slide both seats all the way forward remove screws in sides of console if no screws on sides slide seats back and pull center from inside remove two bolts remove side skirt on each side screws under them remove ashtray center pocket screws under it also unplug wire connectors and remove

Jul 29, 2012 | 2010 Honda Pilot

1 Answer

Where is the location of oil filter toyota landcruiser deisel V8 turbo 200 series


I have a a V8 Tundra.
Driver side front. You may have to remove skid plate.
Also try turning front wheel hard to the left and look behind the left wheel and you see it.

Feb 06, 2011 | 2010 Toyota Land Cruiser

1 Answer

Toyota tundra 2008 removal radio help


There is a hidden screw under the center knob on the heater control. Remove this, and the other 2 srews hidden in the corners of the air registers.

Oct 08, 2009 | 2008 Toyota Tundra

1 Answer

Take out dash(tundra) for antenna installation


You could do an antenna installation without removing the dash. Take out the center assembly with the radio and hvac controls and the glove box. You'll have enough access to run the antenna wire from its stock location to the radio.

Mar 31, 2009 | 2004 Toyota Tundra

Not finding what you are looking for?
2010 Toyota Tundra Logo

Related Topics:

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...