Question about Cars & Trucks

1 Answer

Broke fuse off and can't get prongs out...how do I get fuse prongs out without damaging it any more?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 23 Answers

Disconnect your battery and carefully grab with needle nose pliers being very careful not to damage the socket the fuse plugs into.

Posted on Dec 30, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I SHORTED OUT CIG. LIGHTER NOW DOOR LOCKS,POWER CONTROL FOR MIRROWS,COUTESY LIGHTS AND CIG LIGHT WON'T WORK ALL FUSES ARE OK NOW THE CRUISE CONTROL STOPPED WORKING


You must have a blown fuse. Did you test each fuse with a ohm meter? Keep in mind you must remove each fuse from the fuse block to test it. If you touch the meter leads to the two metal bits on top of the fuse without removing it from the circuit, you could get a false reading or damage your meter. Also, a blown fuse doesn't necessarily have to look charred and black inside, depending on where the element broke. Your vehicle manual should have a diagram showing what each fuse is for. This might save you the trouble of checking every fuse, and confirm the fuse was put back into the correct slot.

Dec 07, 2015 | Cars & Trucks

1 Answer

1989 mitsubishi lancer ,TIMING BELT BROKE HOW TO CHECK WITHOUT DISMANTLING


as it is an interference engine it is a sure bet that the valves will be bent. If you have already fitted a new belt then do a compression test

Jul 04, 2013 | Cars & Trucks

1 Answer

Pulled fuse out but it broke prongs still inside and won't pull out how do I get them out without damaging it more?


looks like a relay.
disconnect the battery first, then try needle nose pliers and a hook & pick set from your local autoparts store.

Dec 30, 2012 | Cars & Trucks

1 Answer

Cant pull 140 alt fuse rx 330


No it isn't bolted in. Disconnect battery and then use needle nose pliers to pull the pins.

Feb 16, 2012 | Lexus RX 330 Cars & Trucks

1 Answer

I was changing the head light bulb and one of the prongs broke what can i do?


If it was a prong on the bulb, you will probably need to get another bulb. If it was a prong in the
bulb socket, you will probably be able to get another at a parts house.

Mar 04, 2011 | 2000 Mitsubishi Galant

1 Answer

If the axle is broke or removed does that mean that the difereincal pin broke or damaged or if the gears are damaged


never seen an axle fall out--you may have major damage. If you are lucky, the cv joint may have failed suddenly without damaging the tranny or wheel bearing. What do the shaft ends look like? Does it have splines on both ends? Are the splines clean? If yes, you may be OK--just have a new axle put in.

Aug 22, 2010 | 1993 Plymouth Voyager

1 Answer

Could a silver square relay looking fuse thingy broken off stop my wipers from working?


I replaced my relay as my wipers stopped working after replacing the relay my wipers work again was going to get a new wiper motor but glad I tried the relay first so much easier

Apr 17, 2009 | 1996 Jeep Cherokee

1 Answer

98 ford contour heater wire leading into interior fuse box


corrosion can cause a week connection .if the wire you replaced it with was used it could have had the (cancer ) inside already

Jan 06, 2009 | 1998 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...