Question about 2008 Kia Rio

Open Question

Where are the crankshaft sensor and transmission sensors

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't locate my crankshaft sensor on my 1995 ford probe


Look on the link below. There's a few images which will help you locate that sensor:

location of 1995 ford probe crankshaft sensor Google Search


The sensor will be located located where the engine attaches to the transmission. Have a look around where the engine attaches to the transmission .. top, sides and underneath. The crankshaft sensor will have a minimum of 1 wire attached.

You'll locate it easily

Apr 22, 2016 | Ford Cars & Trucks

2 Answers

I have these codes reading now po700 po335 and po727 any idea what to check first on 03 kia sorento. my car lost power then shut off, then wouldn't start


p0335 is a crank shaft sensor error. This sensor is what tells the ECM when to send spark to plugs. That is why it wont start.

Apr 02, 2016 | Kia Cars & Trucks

1 Answer

What is code p0727


Possible causes
- Faulty Crankshaft Position (CKP) Sensor
- Crankshaft Position (CKP) Sensor harness is open or shorted
- Crankshaft Position (CKP) Sensor circuit poor electrical connection
- Communication error between the Engine Control Module (ECM) and Transmission Control Module (TCM)

The P0727 Codes is triggered when the TCM receives no signal from the ECM.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0727 Description
The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM).


May 06, 2015 | Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Where is the crankshaft sensor located?


You will find the crank sensor on the right side (passenger) just on the back side of the seam between the engine and the transmission where the flex plate that connects them is located. It is just above the surface of the differential housing. It has a connector that you would separate by lifting gently on the tab. Then unbolt the old sensor and pull it up out of the housing.

I hope this helps, thanks for useing FixYa.

Jul 01, 2011 | 1999 Dodge Intrepid

1 Answer

HELP ! Sensor crankshaft position SUZUKI AERIO SX AWD 2.3L 2005.How to replace under the scheme ?


Welcome to FixYa.com
Crankshaft Position (CKP) Sensor Removal and Installation

Removal

1. Remove engine with transmission from vehicle.

2. Remove transmission from engine and then remove flywheel or drive plate from crankshaft.

3. Disconnect connector from crankshaft position sensor.

4. Remove crankshaft position sensor (1) from cylinder block (2).

Installation

Image

Reverse removal procedure noting the following.

- Check to make sure that crankshaft position sensor (1) is free from any metal particles and

damage.

- Apply engine oil to O-ring of sensor.

- Install crankshaft position sensor to cylinder block (2) with specified torque.

Tightening torque

Crankshaft position sensor bolt a: 6 N.m (0.6 kg-m, 4.5 lb-fl)

- Connect connector and fix wire harness with clamp securely. Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician
leedavidian_133.png

Feb 06, 2011 | 2005 Suzuki Aerio SX

1 Answer

Looking for location of crankshaft position sensor on 2000 mercury villager with 3.3l engine. parts store says there are 2 per vehicle. found one at front of engine. any idea where the 2nd one would be?


The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing The bottom of the sensor is positioned next to the drive plate. Remove the 10mm bolt holding the sensor in place and remove the sensor. Install the new crankshaft sensor.
Install crankshaft sensor bolt and tighten. Connect wiring. merry christmas !!

Dec 25, 2010 | 2000 Mercury Villager

1 Answer

How do you replace the crankshaft sensor on a 2000 chev tracker-automatic 2 litre, with air.


If you have doubts about doing this repair I suggest you let and Certified Mechanic (ASE) do the repairs its not and easy task



REMOVAL PROCEDURE
  1. Disconnect the electrical connector from the crankshaft position (CKP) sensor.
  2. Remove the transmission from the vehicle.
  3. Remove the flywheel or the flex plate from the crankshaft.
  4. Remove the 2 bolts (3) and the sensor wire harness clips or shield.
  5. Remove the bolt (4) securing the CKP sensor to the engine block (5).
  6. Remove the CKP sensor (1) and the wire harness (2) from the vehicle.
  7. Inspect the CKP sensor signal rotor for damaged or missing teeth through the CKP sensor opening.
  8. 0882f41.gif
INSTALLATION PROCEDURE

NOTE: Do not pinch or damage the CKP sensor wire harness between the engine block and transmission during the transmission installation. Observe that the CKP sensor wire harness remains properly located in the channel provided at the rear of the engine block during the installation.

  1. Lubricate the CKP sensor O-ring with clean engine oil.
  2. Install the CKP sensor (1) to the engine block (5)
  3. Secure the CKP sensor to the engine block with the bolt (4). Tighten Tighten the bolt to 6 N.m (54 lb in) .
  4. Secure the sensor wire harness to the engine block with the clips or the shield and the 2 bolts (3).
  5. Install the crankshaft flywheel or flex plate.
  6. Install the transmission.
  7. Connect the CKP sensor electrical connector.
Good luck

Oct 18, 2010 | 2000 Chevrolet Tracker

2 Answers

Where is the crank sensor located on a 2000 grand cherokee limited 4.0?


4.0L
The Crankshaft Position Sensor (CKP) is mounted to the transmission bellhousing at the left/rear side of the engine block. Engine speed and crankshaft position are provided through the crankshaft position sensor. The sensor generates pulses that are the input sent to the powertrain control module (PCM). The PCM interprets the sensor input to determine the crankshaft position. The PCM then uses this position, along with other inputs, to determine injector sequence and ignition timing. The sensor is a Hall effect device combined with an internal magnet. It is also sensitive to steel within a certain distance from it.
On 4.0L 6-cylinder engines, the flywheel/drive plate has 3 sets of four notches at its outer edge. The notches cause a pulse to be generated when they pass under the sensor. The pulses are the input to the PCM. For each engine revolution there are 3 sets of four pulses generated.
The trailing edge of the fourth notch, which causes the pulse, is four degrees before top dead center (TDC) of the corresponding piston. The engine will not operate if the PCM does not receive a crankshaft position sensor input.

This is a photo of the bell housing on the transmission:

b094b8a.jpg

Oct 07, 2009 | 2000 Jeep Grand Cherokee

5 Answers

Looking for crankshaft sensor location


rear of bellhousing transmission mates to engine...

Aug 09, 2009 | 1994 Chrysler New Yorker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...