Question about 1996 GMC Jimmy

Open Question

Blower motor relay location on a 1996 gmc jimmy

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 21 Answers

SOURCE: How to uninstall a blower motor on a 1999 GMC JIMMY

Yeah if you have to tap on it, then that means the brushes in the motor are worn out and you need to replace it. The blower motor is behind the PCM and Coolant Overflow bottle. If you remove these then it will give you better access to motor. You'll have to cut around housing. There should be a groove already there for you, just make sure you don't cut all the way around it. Once you open it and get the new one installed, you'll have to use caulk to seal where you cut it at.

Posted on Dec 20, 2009

Ad
  • 72 Answers

SOURCE: need location of fuel pump relay on 98 gmc jimmy

In the Underhood Bussed Electrical Center

Posted on Jun 24, 2009

  • 62 Answers

SOURCE: blower motor resistor location on a 1996 gmc 1500?

It is located on top of the heater box in the passenger side remove the glove box to gain acess there are two 7mm srews and a relay braket holding it in place it is a tight squeeze but can be removed with a 1/4 inch ratchet.

Posted on Aug 01, 2009

ministock48
  • 258 Answers

SOURCE: 1996 GMC blower motor only works on high speed.

more than likely yes the resistor

Posted on Oct 22, 2009

  • 1201 Answers

SOURCE: wath P1406 Code means on a GMC jimmy 1996,

It's an egr valve problem (exhaust gas return) egr position sensor.
Take off the egr valve and turn it over and see if there is carbon build up in the ports, if there is clean it out with a pipe cleaner and a little carbon cleaner, just spray a little into the ports and clean it out. If that doesn't cure the problem, then either the sensor needs replacing, and or the egr valve.

Posted on Apr 15, 2010

Testimonial: " thanks for yout help"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 GMC Jimmy starter relay how to replace and install


The relay is located in the Underhood Bussed Electrical Center (UBEC) on the left side of truck. The starter relay is the large one in approximately the middle under the lid. Get a new one, pull it out and push the new one in.

Nov 28, 2016 | 1996 GMC Jimmy

1 Answer

Blower motor does not work on high


faulty blower motor resistor usually located near blower motor

Dec 29, 2013 | 2001 GMC Jimmy

1 Answer

Blower motor not working


I had a similar problem with my Jimmy and it turned out to be the switch on the dash. But the easiest way to rule out the blower motor is to apply 12 volts directly to the blower motor itself, if that works move to testing the switch.

Jan 08, 2013 | 1996 GMC Jimmy

1 Answer

Where to cut power on 1996 gmc jimmy fuel pump


fuel pump relay is located inside the glovebox. there is a pull away panel in the back left corner, should be the center relay.

Sep 21, 2010 | 1996 GMC Jimmy

2 Answers

Where is the blower motor relay located


The blower motor relay is the 2nd relay on the cowl.You will see them up on the wall by the hvac assembly.This is the hi blower relay.Hope this helps.Good luck.

Mar 11, 2010 | 1995 GMC Jimmy

1 Answer

Were is the blower motor located at on a 1996 gmc yukon


It's located on passenger side top corner of firewall.you have to remowe ECM unit and coolant reservoir to get to it.It's held by 3-4 screws.Then you'll have to cut the seam with razor blade in order to remove it from housing.

Jan 04, 2010 | 1999 GMC Jimmy

1 Answer

Blower motor resistor location on a 1996 gmc 1500?


It is located on top of the heater box in the passenger side remove the glove box to gain acess there are two 7mm srews and a relay braket holding it in place it is a tight squeeze but can be removed with a 1/4 inch ratchet.

Aug 01, 2009 | 1996 GMC Sierra

Not finding what you are looking for?
1996 GMC Jimmy Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...