Question about Cars & Trucks

Open Question

How do i locate the egr valve on a vauxhall vivaro 2.0litre 2008 van

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: vauxhall vivaro wont start cold

Sounds like a faulty cold start assistor. On top of the engine you will find an aluminium housing with four things that look like glow plugs screwed into it. These 'glow plugs' are only available complete with the housing fron Vauxhall. Approx £70 +
Airbag light is probably a fault with the seatbelt pretensioner.
Check the wiring under the seats for damage or perhaps the plugs have pulled apart.

Posted on Jan 28, 2009

  • 398 Answers

SOURCE: egr valve location

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

Posted on Mar 07, 2009

c17hydro
  • 2984 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

  • 1 Answer

SOURCE: Vauxhall Vivaro Van 53 plate. Wipers not Parking

hi i have the same problem...can you tell me if you have an answer yet???

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Renault senic 1.9 cdi start but wont rev up,glow plug light come on


try this informative website----https://axleaddict.com/auto-repair/How-to-remove-clean-or-bypass-an-egr-valve-from-a-trafic-vivaro-primastar-diesel-van ----this has same engine as your scenic

Jan 04, 2017 | Renault Cars & Trucks

1 Answer

How do i top up automatic transmission fluid. vauxhall vivaro van


Poor the transmission fluid directly into the dipstick tube slowly to avoid over filling. Check the fluid as you pour it in little by little so you don't over fill it.

Oct 14, 2015 | Vauxhall Cars & Trucks

1 Answer

How do i top automatic transmission fluid. vauxhall vivaro van


Car manual tells you how much to add. Whatever you do, DO NOT OVERFILL.

Oct 14, 2015 | Vauxhall Cars & Trucks

1 Answer

Remove indicator stalk on Vauxhall Vivaro


Remove steering wheel remove covers around switch check mounting bolts unplug switch loosen off securing bolt, lift off the column..

Nov 18, 2014 | Cars & Trucks

1 Answer

On my vauxhall vivaro van, the fan heater isn't very good and when I turn it to number 4 it blows the fuse, the fuse is a 32amp how do I can the fan motor??


Usually on cars there is a blower motor resistor that changes the amount of amperage to the fan motor. If that is fried or shorted out than you could be receiving too much juice and piping your fuse. Either way there is some kind of short.

Mar 28, 2013 | Cars & Trucks

1 Answer

Where's my fuel filter located in my vauxhall vivaro


opel vivaro ,its a belly tank and its mounted amidships ,about time they dropped the vauxhall and the holden names ,havent got a 1960s rust bucket cresta laying around in the garage have you ?? or a MkIV zodiac executive ,swop for a 1956 morris oxford ???

Feb 15, 2011 | Volkswagen Tiguan Cars & Trucks

2 Answers

Vauxhall Vivaro Van 53 plate. Wipers not Parking


hi i have the same problem...can you tell me if you have an answer yet???

Sep 21, 2009 | 2003 AMC Encore

1 Answer

Vauxhall vivaro wont start cold


Sounds like a faulty cold start assistor. On top of the engine you will find an aluminium housing with four things that look like glow plugs screwed into it. These 'glow plugs' are only available complete with the housing fron Vauxhall. Approx £70 +
Airbag light is probably a fault with the seatbelt pretensioner.
Check the wiring under the seats for damage or perhaps the plugs have pulled apart.

Oct 30, 2008 | 2002 Volkswagen Eurovan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...