Question about Ford Focus

Open Question

How to replace windshield washer pump in 2005 ford focus

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replacing windshield washer pump

I assume you access from underneath. Remove plastic shroud and expose reservoir and pump? right?

Posted on Nov 11, 2008

Ad
chrischronic
  • 235 Answers

SOURCE: windshield washer will not work even though the wipers do on a fo

check the fuse, if its ok youre gonna need a new pump.

Posted on Jan 15, 2009

freetek
  • 5568 Answers

SOURCE: 2002 Dodge Caravan Windshield Washer

If the pump still makes noise, you may just have clogged nozzles, have you tried those yet? Also, if you have windshield cleaner left over from summer, it may have frozen in the lines. 

Posted on Jan 26, 2009

  • 1 Answer

SOURCE: Windshield washer fluid pump quit. 2005 Jetta

I have a 2003 Jetta and the fuse box is between the dashboard and the drivers side door. There is a lid that covers it on the dashboard side. Inside there is a diagram/fuse card. The card has one top rectangular series of fuses numbered 8 through 23. Below is a square series numbered 24 through 44. The washer fuse is number 24 on the top left of the bottom square series. For me, I checked the fuse and it was good, therefore I am assuming that my pump is dead.

Posted on Jun 17, 2009

  • 1 Answer

SOURCE: fuel pump replacement on 2005 ford focus

Are you sure that you need to replace the pump? I drive a 54 plate mk2 1.6 zetec that wouldn't always start and I was told it was the fuel pump in the tank but because the fault was intermitant I didn't have it fitted and found out that the car didn't start because the fuel lift pump wasn't priming the system before starting. I found that there was a faulty connection on the relay for the pump that is in the compartment under the glove compartment.

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the windshield wiper pump located on dodge caravan 2005


The washer pump is located in the bottom of the washer fluid tank

May 24, 2015 | 2005 Dodge Caravan

1 Answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out


The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.

Apr 07, 2015 | Ford Cars & Trucks

2 Answers

My windshield washer is not working correctly.


Assuming you have washer fluid and you can hear the pump with no flow at the main line I would guess the turbine has separated from the pump shaft.

Sep 30, 2014 | 2006 Ford Focus

1 Answer

Wipers don't work


sounds like wiper control stalks, i am in the uk and it is quite a common fault on the focus

Dec 12, 2009 | 2005 Ford Focus

2 Answers

Windshield washer pump replacment The motor runs but doesn't pump


cheak the small pipes are not traped under the hood happened on mine

Nov 24, 2009 | 2005 Ford Focus

1 Answer

Wash wipe on a Focus 2000 model


I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...