Question about Cars & Trucks

Open Question

How to remove and install Kia Rondo 2.0L (G4KA engine) Throttle Cable from Throttle Body without upsetting the original cable tension?

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: how do you change the spark plugs on a kia optima 2.7 v6

you have to remve the bolts on top and sides of the plenum assy be sure not to drop anything down in the lower intake!!!!! the bolt heads are 12mm and there are 2 on top 2 on the ends and three int the front

Posted on Apr 16, 2009

  • 91 Answers

SOURCE: 1996 s-10 pickup parking/ e-brake cable remove & install ???

no they are not thet easy if you are not sure would take to professional for help talk to friends i bet they know someone who will help or do it for you

Posted on Apr 28, 2009

  • 14 Answers

SOURCE: engine revs to high

Worth looking to see if the piston is sticky in the carb dashpot. Remove the air filter and lift the piston up with your finger - does it return smoothly and go right to the bottom? If not then remove the dashpot and piston, clean up with cellulose thinners or carb cleaner and replace. Tighten the screws evenly while checking that the piston keeps returning - if there is a little stickyness then tap the dashpot with the plastic end of a screwdriver util the piston returns smoothly and then tighten the screws fully. It's also worth checking the mixture because a non standard filter is fitted.

Posted on May 22, 2009

  • 1348 Answers

SOURCE: how to install parking brake lever cable on new

you have to install it into the inverted shoe first,then install the shoe

Posted on Jul 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear spark plugs on the firewall on a 2008 Kia Rondo with a 2.7 liter engine


a bit of this & that; probaly need a jack (raise engine relative to body/firewall or opposite that) and an assortment of socket extensions, swivel joint & patience. Do it w/ engine cold & use a little 'never sieze' on new plugs. It is possible, just not convenient.

Dec 26, 2016 | 2008 Kia Rondo

1 Answer

When i turn on heater or fan engine revs over 3000 rpm


Idle Air Control Valve Pintle may be bad If you disconnect the IAC and the problem ceases it can point to this being the problem.: Removal & Installation 3.5L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the fuel injector sight shield.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • The air cleaner intake duct. Figure of IAC and TPS electrical connectors disconnected. aurora_g1.gif

    • The idle air control (IAC) valve and throttle position (TP) sensor electrical connectors. Figure of cruise control and throttle control cables removed from throttle lever. aurora_g2.gif

    • The cruise control cable and throttle control cable from the throttle body lever.
    • The fuel pressure regulator vacuum hose, positive crankcase ventilation (PCV) hose and the throttle body vacuum port hose.
    • The throttle body coolant hoses.
    • The throttle control cable bracket, leaving the throttle and cruise cables connected.
    • The upper nut holding the throttle body to the intake manifold.
    • The throttle body assembly.
  5. Clean the gasket mating surfaces.
To Install:
  1. Install a new gasket and new studs if necessary.
  2. Install or connect the following:
    • The throttle body assembly.
    • Start the top nut by hand.
    • The throttle body coolant hoses.
    • Position the throttle control cable bracket and hand start the retaining nuts and bolt.
    • Torque the three throttle body retaining nuts to 89 in.lbs. (10 Nm). And the bracket retaining bolt to 115 in.lbs. (13 Nm).
    • The throttle body vacuum port hose, PCV valve hose and the fuel pressure regulator hose.
    • The throttle control and cruise control cables to the throttle body lever.
    • The IAC valve and TP sensor electrical connectors.
    • The air intake duct.
  3. Refill the cooling system.
  4. Install the fuel injector sight shield.
4.0L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable.
    • The Mass Air Flow (MAF) sensor electrical connector.
    • The air cleaner intake duct.
    • The PCV valve fresh air tube. Figure of cruise control cable removed from throttle cable bracket. aurora_g3.gif

    • The cruise control cable and throttle control cable from the bracket.
    • The cruise control cable and throttle control cable from throttle body lever. Figure of IAC valve and TPS connectors removed. aurora_g4.gif

    • The idle air control (IAC) valve and throttle position (TP) sensor electrical connectors. Figure of fuel lines removed from retainer on throttle cable bracket. aurora_g5.gif

    • The fuel feed and return lines from the retainer on the throttle control cable bracket.
    • The transaxle shift cable clip from the throttle control cable bracket. Figure of throttle body removed from water crossover. aurora_g6.gif

    • The throttle body from the water crossover.
To Install:
NOTE: The Mass Air Flow (MAF) sensor inlet and the outlet of the air cleaner assembly must line up when installed. Misalignment may cause MIL illumination or driveability concerns.
  1. Install or connect the following.
    • The throttle body to the water crossover. Torque the bolts to 106 in.lbs. (12 Nm).
    • The IAC valve and TP sensor electrical connectors.
    • The throttle and cruise control cables to the throttle body lever.
    • The throttle and cruise control cables to the throttle control cable bracket. The transaxle shift cable clip to the throttle control cable bracket.
    • The fuel feed and return line retainer to the throttle control cable bracket.
    • The MAF sensor electrical connector.
    • The air cleaner intake duct clamp. Torque the clamp to 27 in.lbs. (3Nm).
    • The PCV valve fresh air tube.
    • The fuel injector sight shield. Torque the nuts to 20 in.lbs. (2.3 Nm).
  2. Install the negative battery cable.
  3. Pressurize the fuel system and verify no leaks.
prev.gif next.gif

Oct 07, 2010 | 2001 Oldsmobile Alero

1 Answer

Need to replace intake manifold how do you do this


Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
To install:
  1. Install or connect the following:
    Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

VIN K Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

    a5adffa.jpg
    Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
To install:


140d431.jpg
Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


4950e4f.jpg
Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
  1. Install or connect the following:
    Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

May 17, 2010 | 2001 Pontiac Bonneville

1 Answer

Changing spark plugs 2001 Kia sportage


These are really quite easy to do just time consuming. 1. remove the air ducting from the air box and throttle body 2. remove the accelerator cable and kickdown cable(if equiped with auto trans) from the throttle body 3. remove the 4 bolts from the throttle body and be careful to not ruin the gasket upon removal 4. remove the black cover from the rocker cover(valve cover) 5. remove the 2 coli packs and the spark plug wires. 6. remove the 4 spark plugs. Use NGK or Nippon Denso plugs and gapped at .032". Let me know if you need anything else.

May 16, 2010 | 2001 Kia Sportage

1 Answer

Replace starter


REMOVAL & INSTALLATION

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the terminal nuts, washers, and electrical leads from the starter motor.
  4. Remove the passenger side catalytic converter.
  5. Remove the passenger side engine mount nuts, and lower the vehicle.
  6. Disconnect the resonance chamber-to-throttle body ducts.
    1. Detach the electrical connector for the Mass Air Flow (MAF) and the Intake Air Temperature (IAT) sensors.
    2. Disconnect the resonance chamber air intake hose from the air cleaner housing and MAF sensor.
    3. Remove the (IAC) inlet hose and the intake plenum air inlet hoses.
    4. Detach the electrical connector from the switchover valve and the remaining vacuum connections.

  7. Install the engine support fixture J28467-A with adapters J28467-450 or equivalents and raise the passenger side of the engine.
NOTE Passenger side of the engine must be raised approximately 1.5 inches (38 mm).
  1. Raise and safely support the vehicle securely on jackstands.
  2. Remove the engine mount from the engine mount bracket and cradle.
  3. Remove the engine mount bracket bolts and reposition the bracket.
  4. Remove the starter motor from the vehicle.
To install:
  1. Install the starter motor to the vehicle and tighten the bolts to 44 ft. lbs. (60 Nm).
  2. Position the engine mount bracket and install the bolts. Tighten to 30 ft. lbs. (40 Nm).
  3. Install the engine mount to the engine mount bracket and cradle. Partially lower the vehicle.
  4. Lower the engine. Have an assistant guide the engine mount into place while lowering the engine. The engine mount locator tab must engage the slot in the cradle.
  5. Reinstall the resonance chamber-to-throttle body ducts.
  6. Raise the vehicle.
  7. Install the passenger side engine mount nuts. Tighten the upper nut to 30 ft. lbs. (40 Nm). Tighten the lower nut to 41 ft. lbs. (55 Nm).
  8. Install the passenger side catalytic converter.
  9. Plug in the electrical leads, install the washers, and terminal nuts to the starter motor. Tighten the battery cable terminal nut to 115 inch lbs. (13 Nm). And the solenoid terminal nut to 35 inch lbs. (4 Nm).
  10. Lower the vehicle.
  11. Connect the negative battery cable.

4.6L Engine
  1. Disconnect the negative battery cable.
  2. Disconnect the positive battery cable.
NOTE In order to get to the starter assembly the intake manifold must be removed. Refer to the procedure for removing the intake manifold.
  1. Reposition the front bank spark plug wires.
  2. Remove the air intake duct from the throttle body.
  3. Detach the electrical connectors for the intake manifold, Throttle Position (TP) sensor, and Idle Speed Control (ISC) motor, Evaporative Emission (EVAP) Control solenoid and Cruise Control Servo.
  4. Disconnect the vacuum hoses at the brake vacuum booster, fuel pipe bundle and to the body.
  5. Disconnect the PCV hoses at the intake manifold.
  6. Unhook the accelerator cable at the throttle body and position it out of the way.
  7. Relieve the fuel system pressure. Disconnect the fuel pipe quick connects at the fuel pipe bundle in the engine compartment.
  8. Remove the EVAP solenoid bracket at the rear (or right) cam cover.
  9. Reposition the transaxle range control cable away from the cruise control servo.
  10. Disconnect the coolant hoses at the throttle body and to the coolant reservoir and plug the hoses. Wrap a shop towel around the hoses when disconnecting to avoid spillage.
  11. Remove the four intake manifold bolts and lift the intake manifold with the throttle body out of the engine compartment.
  12. Unbolt the solenoid 'S' terminal nut and battery cable nut. Remove the starter motor mounting bolts, and lift the starter motor out of the manifold cavity.
To install:

NOTE Before installing the starter motor to the engine, tighten inner nuts on the solenoid terminals to be sure they are secure in the cap. Tighten the inner nuts on the battery terminal and motor terminal to 71 inch lbs. (8 Nm). If the nuts are not properly tightened, the starter may fail later due to the terminal or cap damage.
  1. Install the solenoid switch lead, and tighten the nut to 22 inch lbs. (2.5 Nm).
  2. Install the battery cable nut and tighten to 71 inch lbs. (8 Nm).
  3. Install the starter motor and tighten the mounting bolts to 22 ft. lbs. (30 Nm).
  4. Install the intake manifold with the throttle body onto the engine and install the four bolts. The four intake manifold bolts must be tightend in a specific sequence to 71 inch lbs. (8 Nm), then an additional 120°.
  5. Connect the coolant hoses at the throttle body and at the coolant reservoir. Add coolant as needed.
  6. Position the transaxle range control cable to the cruise control bracket.
  7. Fasten the EVAP solenoid bracket to the rear cam cover.
  8. Reconnect the fuel pipes quick connects at the fuel pipe bundle in the engine compartment.
  9. Hook the accelerator cable up at the throttle body.
  10. Connect the vacuum hoses at the brake vacuum booster, fuel pipe bundle and to the body. Install the PCV hose at the intake manifold.
  11. Install the electrical connectors for the intake manifold, the TP sensor ISC motor, EVAP solenoid and the cruise control servo.
  12. Install the air intake duct to the throttle body.
  13. Reposition the front bank spark plug wires.
  14. Connect the negative battery cable.
  15. Connect the positive battery cable.

4.5L and 4.9L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the starter motor shield.
  4. Remove the exhaust front and rear pipe assembly.
  5. Remove the flexplate inspection cover.
  6. Disconnect the solenoid 'S' terminal nut and battery cable nut.
  7. Unbolt the starter motor mounting bolts, and remove the starter motor.
e2d3282.jpg
Fig. Typical starter mounting on early models

b5066a8.jpg
Fig. Later model starter location and mounting on the 4.9L engine


a697aa3.jpg
Fig. Starter mounting on 4.5L engine with a starter shield


To install:
  1. Install the starter motor, and tighten to 32 ft. lbs. (43 Nm).
  2. Install the solenoid 'S' terminal nut. Tighten the nut to 35 inch lbs. (4 Nm).
  3. Install the battery cable nut and tighten to 12 ft. lbs. (15 Nm).
  4. Install the flexplate inspection cover, the front and rear exhaust pipe assembly and the starter motor shield.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope trhis help (remember comment and rated this).

Apr 08, 2010 | 1992 Cadillac DeVille

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

2 Answers

Pontiac bonneville 3.8 vin code k . I replaced the in take gasket because it was leaking water between the top an bottom intakes going into the cyclinder heads its still leaking after all this work ive...


This is the entire task for it. It sounds like you might not have torqued it correctly, or your intake is cracked. But take a look at all of the info:

VIN K Engine On these engines, the upper and lower intake manifolds must be removed separately.
  1. Properly relieve the fuel system pressure, as outlined in Section 5 of this manual.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Remove the fuel injector sight shield and air intake duct.
  5. Tag and disconnect the spark plug wires on the right side of the engine and position aside.
  6. Remove the manifold vacuum source.
  7. Remove the fuel rail.
  8. Remove the EGR heat shield.
  9. Unfasten the cable bracket-to-cylinder head mounting bolt.
  10. Disconnect the throttle cable.
  11. Remove the throttle body support bracket.
  12. Unfasten the upper intake manifold bolts, then remove the upper manifold.
This engine has two bolts which are hidden beneath the upper intake. These bolts are located in the right front and left rear corners of the lower intake manifold. This is why it is necessary to remove the upper before servicing the lower manifold.
  1. Disconnect the upper radiator hose.
  2. Remove the alternator, as outlined in Section 2 of this manual.
  3. Remove the drive belt tensioner.
  4. Remove the EGR valve outlet pipe.
  5. Unfasten the intake manifold bolt, then remove the manifold from the vehicle. Remove and discard the gaskets. Thoroughly clean the gasket mating surfaces, intake manifold bolts and bolt holes.
To install:
  1. Position a new gasket, then place the lower intake manifold over it. Apply a suitable threadlocking compound to the bolts, then install them. For 1995 vehicles, tighten the bolts twice, to 88 inch lbs. (10 Nm), in the sequence shown in the accompanying figure. For 1996-97 vehicles, tighten the bolts to 11 ft. lbs. (15 Nm), in the sequence shown in the accompanying figure.
    1. Install the EGR valve outlet pipe.
    2. Install the drive belt tensioner.
    3. Install the alternator.
    4. Connect the upper radiator hose.
    5. Position the upper intake manifold on the lower manifold. Install the retaining bolts and tighten to 89 inch lbs. (10 Nm).
    6. Install the throttle body support bracket, then connect the throttle cable.
    7. Install the cable bracket-to-cylinder head mounting bolt.
    8. Install the EGR heat shield.
    9. Install the fuel rail.
    10. Install the manifold vacuum source.
    11. Connect the right side spark wires on the right side of the engine.
    12. Install the fuel injector sight shield and air intake duct.
    13. Fill the cooling system with the proper type and amount of fluid.
    14. Connect the negative battery cable. Start the engine and check for leaks. Check the cooling system, and add as necessary.

Oct 18, 2009 | 1995 Pontiac Bonneville

1 Answer

How do you replace the alternator on a 2000ford contour



Removal & Installation

2.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove the air cleaner-to-throttle body tube and the mass airflow sensor.
  4. Unplug the connectors and remove the cables from the alternator.
  5. Raise and support the vehicle.
  6. Release the drive belt tensioner and remove the drive belt from around the alternator.
    NOTE It is not necessary to remove the drive belt from the engine.
  7. Remove the alternator mounting bracket bolts and remove the mounting bracket.
  8. Lower the vehicle.
  9. Remove the power steering pressure hose bracket retaining nut and bolt and remove the bracket with the hose from the engine lifting eye.
  10. Remove the alternator mounting bolts and remove the alternator from the vehicle.
  11. To install:
    1. Place the alternator into position and install the mounting bolts finger tight.
    2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
    3. Raise and support the vehicle.
    4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
    5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
    6. Lower the vehicle.
    7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
    8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
    9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
    10. Connect the negative battery cable. To install:
      1. Place the alternator into position and install the mounting bolts finger tight.
      2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
      3. Raise and support the vehicle.
      4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
      5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
      6. Lower the vehicle.
      7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
      8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
      9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
      10. Connect the negative battery cable.


Sep 28, 2009 | 2000 Ford Contour

1 Answer

Water pump in a kia saphea how do u change it 2001


Hi there,

Below are the steps..

Disconnect negative battery cable.
3b9f19b.jpg

Drain engine coolant.
1eadff0.jpg

Remove timing belt (please make sure you know how to do this, otherwise, seek help from a certified mechanic) Remove tensioner and idler. f644145.jpg Remove water pump. dbfdc5c.jpg Remove any gasket fragments, dirt or oil from sealing surfaces. Install new gasket on water pump. To prevent dropping the gasket when installing, put sealant in gasket groove. But do not apply to sealing surfaces. Install water pump. Install tensioner, idler and timing belt. Fill engine coolant. Connect negative battery cable. Start engine and check for leaks. Regards, Jeep Brainy

Sep 09, 2009 | 2000 Kia Sephia

2 Answers

Replace alternator


This is for both size engines since you didn't list the motor size......


REMOVAL & INSTALLATION 2.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove the air cleaner-to-throttle body tube and the mass airflow sensor.
  4. Unplug the connectors and remove the cables from the alternator.
  5. Raise and support the vehicle.
  6. Release the drive belt tensioner and remove the drive belt from around the alternator. NOTE: It is not necessary to remove the drive belt from the engine.
  7. Remove the alternator mounting bracket bolts and remove the mounting bracket.
  8. Lower the vehicle.
  9. Remove the power steering pressure hose bracket retaining nut and bolt and remove the bracket with the hose from the engine lifting eye.
  10. Remove the alternator mounting bolts and remove the alternator from the vehicle. To install:
  11. Place the alternator into position and install the mounting bolts finger tight.
  12. Install the power steering hose bracket and tighten the retaining nut and bolt to 70–106 inch lbs. (8–12 Nm).
  13. Raise and support the vehicle.
  14. Install the alternator mounting bracket and retaining bolts and tighten to 15–22 ft. lbs. (20–30 Nm).
  15. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
  16. Lower the vehicle.
  17. Tighten the alternator mounting bolts to 15–22 ft. lbs. (20–30 Nm).
  18. Install the alternator connectors and the cables. Tighten the terminal nut to 80–97 inch lbs. (9–11 Nm).
  19. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
  20. Connect the negative battery cable.

Apr 01, 2009 | 1999 Mercury Mystique

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...