Question about 2003 Ford Ranger Regular Cab

1 Answer

Ford Ranger - Performance Modual

Do Performance moduals work and are they safe ???

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Yes they do work but if you spend the money make sure you buy a brand name one not sure $20. one off the internet do some research. One the the easiest ways would to be just to buy a K&N air filter and have a exhaust shop put on perforamance exhaust or buy it you're seft most kits are easy and bold right on

Posted on Jan 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The 4 wheel drive quit working in my 1993 Ford Ranger extra cab. I got it working once for a little while today but it won't re-engage. I've checked all the fuses and put in another control modual.

90% of the time it is your transfer case shift motor!

Remove the cover of the transfer case shift motor (3 tamper resistant tore screws) making sure to mark the position of cover carefully as to get it back on in the same way it comes off. Inside you will find a round slip plate that some copper contacts run on. I usually clean these with some electronic cleaner, then gently bend the little fingers that are inside there, so they make a better contact on the circuit board. Apply some dielectric grease to protect from moisture and reassemble.

Here's a great video on how to do it.

1989 1992 Ford Ranger Shift Motor Repair

Feb 19, 2018 | Ford Cars & Trucks

1 Answer

No spark on my 1988 ford ranger 2.9 moter replaced new coil

More than likely its the ignition modual...

Aug 16, 2012 | 1988 Ford Ranger

1 Answer

Firing and getting gas wont start

Could be pick up coil or ignition modual...Common problem in those trucks....hope this helps and if so Please rate this post and good luck.

Aug 15, 2012 | 2000 Ford Ranger SuperCab

1 Answer

97 ford ranger wont go into 4low

You replaced the actuator and motor ? That should have fixed the problem. It seems that the replacement of the actuator thermister is still not working properly. Some of the newer actuator switches are not very good. Get one for an older truck . it has been said they are better quality . But the newer ones sometimes don't work.

Dec 30, 2009 | 1997 Ford Ranger SuperCab

1 Answer

The wiring coming from the coil pack on a 1989 ford ranger 2.3 i have changed the coil pack put it still is not firing

If you test the wireing with a test light you shoul have a bright light on one side and a slightly dimmer light on the other post,if so you may need an ignition modual.

Dec 07, 2009 | 1989 Ford Ranger

1 Answer


there is actually a modual that runs the lights... the lighting control modual (LCM) not saying this is for sure, but a good place to start. keep in mind if u replace the modual, you have to have it flashed(programmed) to the vehicle.hope this helps and good luck

May 25, 2009 | 2006 Ford Expedition

1 Answer

ABS indicator remains on

remove the brake lines and HCU. unplug the modual and istall new modual. if ou havn't had the van checked out, i would, there are a number of things it could be that are alot cheaper than a new modual. could just be a wheel speed sensor.

May 19, 2009 | 2001 Ford Windstar

1 Answer

1988 ford ranger 4x4 v-6 not firing

did you guys put a meter on the wires going into the coil and make sure they are getting power when the key is turned on?

If you do get power then I would check the distributor

If you don't get power then trace the coil wires for a blown fuse or pinched wire

Jan 17, 2009 | 1988 Ford Ranger

1 Answer

EGR Modual

try just simply replacing the fuel filter..10 bucks at a parts store..if that does not work and the ecu is messing up they can be pricy you might be able to get one from a junkyard..

Oct 27, 2008 | 1999 Ford Expedition

Not finding what you are looking for?
2003 Ford Ranger Regular Cab Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5677 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides