Question about Chevrolet Impala

Open Question

Fuse for 2000 impala windshield wiper - Impala Chevrolet Cars & Trucks

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1201 Answers

SOURCE: windshield washer does not pump fluid

The pump works off the same circuit as the wipers, so it would be same fuse. Most likely the pump is no bad.

Posted on Jan 31, 2009

Ad
cadman000
  • 607 Answers

SOURCE: Windshield wipers will not turn off, I've replace the turn signal/wiper switch and still not turning off

Sounds like the PARK SWITCH within the WIPER MOTOR is at fault, Only way to beat it is relay the motor. Hope this helps

Posted on May 08, 2009

  • 19 Answers

SOURCE: Windshield wiper does not work on INTERMITTENT or

replace the motor.it will stop being goofy after that i promise

Posted on Sep 02, 2009

steve_e_uk
  • 1675 Answers

SOURCE: 2000 VW jetta VR6 windshield wipers wont work

first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 chevy impala,drivers side windshield works great,the passenger side doesn't work at all,help!


You mean wiper arm ? Probably broken wiper arm linkage bushing you can't see , under the cowling . Can you move the passenger wiper arm up an down without much effort ? An not the drivers side ? To see it or get at it you would need to pull wiper arms off an take cowling off to get at it . How To Install Replace Wiper Motor 2000 05 Chevy Monte Carlo Impala How To Fix Broken Wipers EricTheCarGuy

Feb 12, 2017 | Cars & Trucks

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

2 Answers

Wiper motor


Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Feb 13, 2016 | 2008 Chevrolet Impala

1 Answer

Windshield wipers on 2004 chevy impala when just the driver side works


Did u replace fuses/windshield wiper relay ,both relays ,should be 2 inside the engine compartments fuse box, if not that then the wiper transmission arm could be partially busted or stripped....seems like common problem on this page, maybe lookup if might be free recall replacement

Oct 08, 2015 | 2004 Chevrolet Chevrolet Impala

2 Answers

2000 toyota camry windshield wipers won't work


First I would look in the fuse box by the driver side and check the fuse,if good then get a meter and see if power is going to wiper motor,if so,then wiper motor is bad,if no power is going to motor,then bad switch,here's a link to see. Repair Guides Windshield Wipers And Washers Windshield Wiper Motor...

Windshield Wiper Switch

Print
REMOVAL & INSTALLATION
The windshield wiper/washer switch is part of the Combination Switch Assembly. Refer to Turn Signal/Combination Switch services procedures.

Oct 18, 2014 | 2000 Toyota Camry

2 Answers

My 2003 chevy impala windshield wipers only work


Replace the wiper motor. It is under the wiper blades. remove the blade arms, remove the plastic bezel, remove the motor. The motor has the delay and speeds built in it.

Oct 16, 2014 | 2003 Chevrolet Impala

1 Answer

Windshield wipers won't respond


start at the beginning, check power with meter coming into the fuse, and out. then at the switch, then at the windshield wiper motors.

Jan 31, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Where is the wiper fuse on impala


Junction Block-Left I/P
Left side of the instrument panel , behind an access panel.
WSW
25A
Windshield Wiper System Module, and Windshield Wiper/Washer Switch

Oct 14, 2012 | 2003 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...