Question about 2002 Isuzu Axiom
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
check engine light indicates that the computer in your vehicle has sensed a electrical problem pretaining to the performance of the engine usualy a diagnostic scan would determine the actual cause, vehicle has to be hooked up to a diagnostic tools.
Posted on Nov 24, 2008
SOURCE: isuzu axiom 2003
there is no dipstick or filling ports in the engine bay. underneath the car near the valve boby pan there are 2 bolts, one for draining the trans., and one for filling the trans. this is not the easiest of repairs and it is quite messy. drop cloths or some kind of catch would be wise. first drain the pan by removing the lower bolt. allow the fluid to completely drain and reinsert bolt. next remove the larger (valve body) pan. there is a filter that you will see is held in place by 3 bolts, remove filter and replace with new one. clean mating surfaces of all debris and fluids. next apply the gasket to the pan you just removed and cleaned. fill the empty pan with about 3-4 quarts of new ATF. a second pair of hands here is recommended. together realign pan to trans. careful not to spill fluid! apply a few bolts to allow for free hands. insert all bolts DO NOT OVER TIGHTEN BOLTS! this is very important, only tighten bolts until gasket just starts to squish. over tighten and you risk a new leak.
now the messy pain in the **** part. in oder to check fluid level, you need to have car parked on level ground. remove the upper bolt from the pan you just reapplied. You will need some sort of pump and a few feet of hose to complete the filling process. fill until fluid runs back out the hole, quickly insert bolt, tighten to specs. and wipe exterior of pan to see for any new leaks.
this should solve any trans. slips do to ATF seepage.
best of luck
Posted on Mar 12, 2009
I have found that one can mark (Paint pen) the gears and teeth (One tooth and one corresponding belt rib) on each gear prior to removing the belt. You can then overlay the old belt on a new belt and mark the same spots on the new belt and then install the belt so your marks on the gears and belt line up as they did before you removed the old belt. Given that your timing was right to start with....if done correctly, this will work.
Posted on May 09, 2009
I just had a garage replace my thermostat on my 2002 Isuzu Axiom. The book calls for 2 hrs labor, no way. iI took the garage more like 5 hrs plus, they ate the additional 3 hrs of labor. Note, the intake manifold must be removed and even then special tools are needed because it is still buried deep down. The garage took pictures ot this one because of how ridiculours Isuzu designed the location.
Posted on Aug 20, 2009
Tips for a great answer:
Nov 05, 2016 | 2002 Isuzu Axiom
Jun 30, 2014 | 2002 Isuzu Axiom
Dec 19, 2011 | 2002 Isuzu Axiom
Oct 11, 2010 | 2002 Isuzu Axiom
Jun 03, 2010 | 2002 Isuzu Axiom
Feb 25, 2010 | 2002 Isuzu Axiom
Aug 08, 2009 | 2002 Isuzu Axiom
May 30, 2009 | 2002 Isuzu Axiom
Feb 01, 2009 | 2000 Isuzu Rodeo
67 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: