Question about Cars & Trucks

Open Question

Replace front wheel bearing 2004 grand vitara

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

  • 125 Answers

SOURCE: repair rear wheel bearing 2004 suzuki grand vitara

I have never changed it by myself.

Just trying to help you during X mass period please consult the following internet site and see if you 'recognise your installation.

www.izook.com/tech/samurai/drivetrain/rearaxlebrg.htm

Sorry If can't do more over
Dan

Posted on Dec 28, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2004 silverado 4x4 2500 left front wheel bearing

  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Posted on Jan 19, 2010

  • 409 Answers

SOURCE: replacing front wheel bearings on a 2004 Suburban

The front wheel bearings are sealed units, and must be replaced with the entire hub assembly. They do not need periodic cleaning/replacing as they did in the old days, if they are not making noise do not bother with them.

Posted on Apr 07, 2010

Testimonial: "Thanks"

ftw1952
  • 10319 Answers

SOURCE: how to replace a rear wheel bearing on a suzuki

Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove front hub


hello anon.
2wd or 4wd car?, this Counts big time? i toss coin; land 4wd.
The USA car can be Vitara or Grand Vitara. and cut in dates vary for that too.
the 2002 has no end locking hubs.
so you must mean front wheel bearing hubs.
ok its easy with tools.

GOT TOOLS?
http://www.fixkick.com/hubs/FW_BEARINGS.html#newer

to be accurate i need full spec on car
country
engine sizes. and if 2wd or 4wd.

my guess is your car has the unified hubs. (bearings can not be removed)
you unbolt it.
you put the new hub on
you torque it to 123-180 Ft/lbs, this is the running torque not a preload)
if not, it will fail fast.

that page even has the FSM chapter page there. to see.
from a real Suzuki, 2004.
can be seen tool, at alldata.com
or at suzuki pit stop , dot com (google it) its there.

Sep 27, 2014 | 2002 Suzuki Vitara

1 Answer

Need To no what size bearing puller I need to use to replace my right hand side bearing for a 2001 grand vitra 2.5litre and how to do it .


no end of car stated, now that makes this impossible
but ill guess front. and guess 2 , 4wd ,?????????
and at what step in process you got stuck>????

all that , just all that..
all that is in the FSM, ever heard off a factory service manual.
or alldata.com
or this.
$4 bucks to look.
https://suzukipitstopplus.com/Products/1191-2001-vitara-grand-vitara-service-manual.aspx
before buying $500 suzuki tools, be it known , generic tools work.

the wheel bearing
ill paste some clues.
I have a printed FSM. (and all above)
here is the factory page
http://www.fixkick.com/hubs/vitara/new-vit-hubs.pdf

the bearing are never replaced in this car, you replace the whole hub.
that is how its done. if you want to break the rules.
then you get to work blind, what bearings are there, , its not publish.
then you get to find that out, and then find a shop to presses them in
and after all that ,its 5x the cost of a hub.
so>>>>>/???

see end of this page for GV front hubs
http://www.fixkick.com/hubs/vitara/new-vit-hubs.pdf

see the list of complex options there. see that.?
2wd, 4wd,?
my guess is yours is 4wd, guess 2.
and uses photo 10 there.

see grapic 10 ,see part id 11?
you pull that off with any slide (slam) hammer made.
then remove the looking ring with special tool used by suzuki
since 1989
then the hub falls off. or if in salt belt,(wiki that)you again
use the slide hammer and bam its off

Pit fall 1,
if you fail to set the nut ring 11 to 156 (or to spec) foot/pounds torque
the bearing will fail in 1000 miles.
see TIMKEN bearing tests proof of that fact, it is a fact.
for all CRUSH bearings.....

Aug 02, 2014 | 2001 Suzuki Grand Vitara

1 Answer

How to replace front wheel bearing?


old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes



  1. Before servicing the vehicle, refer to the Precautions section.


  2. Remove or disconnect the following:



    • Front wheel


    • Brake caliper and rotor


    • Locking hub or hub drive flange, if equipped,(it is)


    • Hub grease cap, if equipped


    • Wheel speed sensor, if equipped (ABS)


    • Wheel bearing lockwasher


    • Wheel bearing locknut (ring) and inner washer


    • Wheel hub and bearing assembly (slide hammer?)


    • Wheel hub oil seal


    • Wheel bearing oil seal


    • Snapring




  3. Press the wheel bearing and race out of the hub.


reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

Jun 26, 2014 | 2000 Suzuki Grand Vitara

1 Answer

1991 vitara front wheel bearing/hub assmby diagram


91 Grand Vitara? They don't show one till '99 just the Sidekick and the Sameri The 99 shows a bearing the the hub presses into. 262071994.jpgThis bearing is the one for the front in a four wheel drive. You did'nt say if your four wheel or not either. This bearing costs 20 bucks at my parts store. This is not the right baring for a two wheel drive as I did'nt think you'd be asking if it was ywo wheel drive. the difference between a 91 and a 99 arn't likly as this information is for vehicals sold in the USA.

Mar 19, 2011 | Suzuki Vitara Cars & Trucks

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

1 Answer

How to replace a rear wheel bearing on a suzuki grand vitara 2004


Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 01, 2010 | 2004 Suzuki Grand Vitara

1 Answer

Repair rear wheel bearing 2004 suzuki grand vitara do i need to pull the axle to remove and replace


I have never changed it by myself.

Just trying to help you during X mass period please consult the following internet site and see if you 'recognise your installation.

www.izook.com/tech/samurai/drivetrain/rearaxlebrg.htm

Sorry If can't do more over
Dan

Dec 28, 2009 | 2004 Suzuki Grand Vitara

1 Answer

Bearing noise from front wheels ; 2002 Suzuki Grand Vitara


these are seal bearing and they need to be press out and press back in this need to be done with a hydralic press not with harmer i can help if yopu are in the nyc are call me 718-821-1640

Jun 09, 2009 | 2002 Suzuki Grand Vitara

2 Answers

1999 Suzuki Grand Vitara Vibrate/shake at 55-70 mph


Lift the back of your car.With a stable rest and with the two hind wheels hanging, run your car up to the speed where you experienced vibration. have someone take care of the throttle and shifting while you observe the transmission shaft. You may have an imbalanced shaft.

May 12, 2009 | 1999 Suzuki Grand Vitara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...