Question about Cars & Trucks

Open Question

Need to assemble a stag wardrobe - Cars & Trucks

Posted by Anonymous on


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Foxguard jp2 immblsr on triumph stag will not de activate or go into service mode.Ignition switch operates as normal but dash lights stay off wipers and washers dont work .

Your half way there. All you need is a wiring diagram to trace the wire from the ignition to that fuse. Most likely it is one wire from the ignition, then it splices to the different fuses. In my experience the splice fails(corrosion), Some times you loose one area, some times all. Depends on which side of the splice is corroded the most. Splices are hard to find. Even harness diagrams can be as much as 2 feet off. I usually find the color code of the wire and run a new wire. In your case, it would be from the ignition switch to the fuse panel.

May 08, 2016 | 1977 Triumph Stag

1 Answer

Triumph stag not starting when hot

what ignition system have you got on your stag? is it the origional twin contact and condenser system, the origional system needed to be setup correctly to work dwell of 26to28degrees the condenser was the favourite suspect.if it has been changed to electronic check for good spark at the king lead. if thats ok no matter which ign. system you have got, the problem may be the twin su fuel pump located in the the boot.make sure the pumps are working should hear them tick at ignition on. it could be fuel vapourisation. is the engine overheating? it will be on stromberg carbs. you should check the diaphams are ok

Feb 28, 2015 | Triumph Stag Cars & Trucks

1 Answer

Distributor troubleshooting

Your distributor may be installed backwards, or maybe just out of phase.
If backwards, you will probably never get it to start and, of course the solution is relatively simple.
If out of phase, the spark may be jumping to a different terminal inside the distributor cap and completely disrupting your ignition timing. See the attached video for an explanation of phasing and how to correct it on your car. (you will need an old distributor cap to drill a hole into so you can confirm spark)
It also occurs to me that the coil you have may not be compatible with your system.

Jul 07, 2014 | 1973 Triumph Stag

1 Answer

Brake pedal goes to the floor

You have air in the system. Look for a broken line leaking brake fluid. You could also have a bad master cylinder, common problem.
If you dont see any leaks and cant bleed the system replace the master.

Feb 22, 2014 | 1970 Triumph Stag

1 Answer

How to remove

Get a kitchen floor brush and hit the balloon.

Dec 21, 2013 | Cars & Trucks

1 Answer

How do I get instructions for a Walton high sleeper with desk and wardrobe

hiya did u manage 2 sort out an instruction book iv just bought a bed with no instructions so any help would be well appreciated thanks

Jan 04, 2013 | Cars & Trucks

1 Answer

Lost instruction manual for MFI millborne triple pine wardrobe

This is a piece of furniture right? Are you looking for assembly instructions?

Dec 25, 2011 | Cars & Trucks

1 Answer

Have 5.5x14 alloys on a triumph stag will 7x14 fit pcd is same

ALL wheels have different offsets,you will need to try the wheel on the car to check the "offset".....will it touch the wheel arch/suspension arms/steering rods on the front and fit inbetween the wing/frame at the may find restricted turning capability from the fronts.......(why would you want to ruin a classic cars looks by fitting these wheels anyway?)

Oct 21, 2010 | Triumph Tr 8 Cars & Trucks

2 Answers

Seting up timing chains on a triumph stag v8

havent done one for 30+years but its not difficult ,similar to doing a jag ,piston at tdc on no one ,then inlet and exhaust fully closed on no 1 ,then you will see the timing marks line up ,think the spots have to be opposite each other and use a straight edge through the centre of the cam bolts and the spots all in line .job done its easy

Jan 09, 2010 | Triumph Tr 8 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides