Question about Cars & Trucks

Open Question

Door panel removal nissan terrano ll

1997

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jdwills
  • 15 Answers

SOURCE: nissan terrano headlight

check out
http://www.sferamydlo.com.pl/Zbyszek/Nissan/R20/el.pdf


Bulb Replacement
The headlamp is a semi-sealed beam type which uses a replacable
halogen bulb. The bulb can be replaced from the engine compartment
side without removing the headlamp body.
I Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1. Disconnect the battery cable.
2. Disconnect the harness connector from the back side of the
bulb.
3. Pull off the rubber cap.
4. Press end of the retaining pin together to release bulb.
5. Remove the headlamp bulb. Do not shake or rotate the bulb
when removing it.
6. Install the new bulb in reverse order of removal.

Posted on Nov 11, 2008

Ad
kf4rwe
  • 25 Answers

SOURCE: Door Panel removal

remove all visable screws from panel and arm rest. Arm rest should come off. Use a flat thin tool or piece of metal and slip it between the panel and the metal door frame. Slip it in about 2 inches,. Slide it back or forth til you hit a stop. That should be a plastic pop in.twist metal tool to pull panel away from the door. It should pop away from door frame. Don't overdo it if it doesn't come out. try another spot. once you get one loose, you can tell how to get the others out. Once panel is loose push it upwards to get top lip out of window bottom. If it has power windows,disconnect plug. If it has manual windows, you will have to remove the window crank There is a snap ring behind window crank that has to be removed.push in on panel by window crank and you can see the ring.

Posted on Dec 06, 2008

  • 279 Answers

SOURCE: remove door trim on nissan terrano 91 4 door

The front doors of the Terrano (D21 Japanese import) are like a jigsaw puzzle, and the bits should fit and come apart without force.
First, look down into the handgrip of the doorpull and you will see a small round plastic plug. Take this out with a sharp screwdriver, and there is the first screw to undo. This allows the handgip to come off, revealing the screw holding the electric window winder switches etc to come off.
The panel of the door itself comes off by carefully pulling the doorcard and the small nylon doorstuds out of the metal frame of the door. Then lift the doorcard up and unhook the the inside door latch wire from the doorcard.
This will reveal the speakers or at least where they should be behind the wire grilles.

As for the alternator belt, may I suggest that you also replace the A/C and the powersteering belts at the same time. Theoretically if one is worn, the others will be,too.
I crawled under the front of the vehicle and took off the splash shield so I could reach up into the crankshaft pulley area.
Both the adjusters for the powersteering andf the alternator can be slackened off from the top of the engine, but I recommend removing the alternator altogether, which allows better access to the adjuster for the A/C belt.Slacken this off.
This tensioner has a roller bearing in the centre of it, take the large bolt out and the tensioner will come off. You will see a bearing in the middle of it, press this out and replace it with a new bearing, it is common and cheap, and if it wears out it will scream very loudly.
Wiggle off the three belts from their pulleys, taking note of their order, and where each drives off the main cranksharft pulley.
Buy the correct replacements (length and Section) and if the belts look like a dog's breakfast, go to someone who can measure them properly. Refit in the correct grooves and pattern, you may have to slacken off the adjusters quite a lot if the old belts have been stretched to the max. Tighten to the correct tension, too much just damages the belts and the bearings in the alternator,a/c, or powersteering; too little allows them to slip and damages belts through overheating.

This is also a good time to check that the auto trans hoses leading to the cooler in the bottom of the radiator are in good condition and the clamps are tight.
Why not replace these hoses, and while you are there, the top and bottom radiator hoses as well?
Then you'll know that it has been done.

Posted on Jan 15, 2009

  • 1986 Answers

SOURCE: need directions to remove driver door interior panel 1997 deville

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

  • 1986 Answers

SOURCE: how do you remove the inner door lining of a 98

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is the glow plug relay on a Nissan terrano


Look in fuse/relay box under bonnet...

Jun 23, 2014 | 1997 Nissan Pathfinder

1 Answer

Where i find the chassis number of terrano


that is the vehicle "VIN" number-on the dash board seen thru the front window on the drivers side or on the drivers door post, and also on your vehicle resigistration card

Apr 29, 2014 | 1997 Nissan Pathfinder

1 Answer

Where the chassis number of terrano


on the door pillar , under hood on plate riveted to front cross member, in the lower corner of windshield attached to dash

Apr 29, 2014 | 1997 Nissan Pathfinder

1 Answer

Hi i have a 1997 Nissan Terrano ll 2.7td SE TOURING


15w40 simi thentic oil?
a lot of tymes peopl put 10w30 this oil is to thin a thicker oil will stick to the valve trane better and raise oil pressure

Nov 27, 2013 | Nissan Pickup Cars & Trucks

2 Answers

How to adjust the handbrake on a terrano ll


On the inboard side of the rear wheel hubs, you will find an oval rubber plug, pry this plug out, to gain access to the brake adjuster.
Pull the handbrake up two clicks.
Jack and support. Remove the rear wheel, and adjust the brake using a screw driver levered through the slot to turn the notched wheel of the adjuster, until the hub starts to drag when rotated by hand. Repeat for the other side. Note the ratchet mechanism on the adjuster will only let it turn one way.

May 03, 2010 | 1994 Nissan Pickup

1 Answer

Remove door panel on 97 nissan maxima


remove screws - they is probably one around the door handle (carefully pry out cover piece) - and underneath any big round (1 inch diameter) plastic screw hole cover - then carefully pry off.

Jan 19, 2010 | 1997 Nissan Maxima

1 Answer

How do you remove the inner door lining of a 98 nissan terrano?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Oct 21, 2009 | 1998 Nissan Pathfinder

2 Answers

Where is the ECU located on the Nissan 94 Terrano


dont know for sure but all nissans ive worked on are behind the passengers side kick panel ( passengers left foot )

Aug 26, 2009 | 1994 Nissan Pathfinder

1 Answer

Removal of air bag


You should disconnect the batter and wait for 15 to 20 min before remove the bag because you want air bags to de energize

Apr 10, 2009 | 1997 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...