Question about Cars & Trucks

Open Question

Front End Noise When Turning

Feels like its slippng

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 468 Answers

SOURCE: front end noise when turning. almost sounds like

There are a couple of things to cause metallic sounds when turning. First thing, is if it's a clicking sound when you turn, then you have a cv joint going bad. It's usually more prominent when moving in reverse, however it can happen just as well while moving forewards. Secondly, if it's more of a grinding or scraping noise, we have a couple of options. The sound could be coming from the brakes, if they're worn or have grit stuck in them, or it could be bad bearings in the front wheel hub. The wheel hub has a tendency to making a whining noise when driving; usually most easily heard when driving past buildings. They can also allow the tire/wheel to present the appearance of leaning when looking at it. If bad enough, it can even rub on the brake caliper, or cause the disc brake rotor to wear out the brake pads prematurely. So, to recap: Check:
CV joints, if a clicking sound brakes or wheel hub bearings if grinding or whining sound.

Posted on Oct 19, 2009

Ad
co7196
  • 3433 Answers

SOURCE: Loud grinding noise from front end

You can see the brake disc on the front wheels, Check both sides of each side, looking for scoring. Brake pads have wear insicators on them that are metal tabs that contact the rotor (disc) when pads get thin. It would be better to pull the wheels off to get a good look at the pads. Good luck

Posted on Jun 03, 2009

jimboz4
  • 305 Answers

SOURCE: front end axle humming

check the oil in your front diff, may need replacing, worst case scenario is the diff bearing is worn

Posted on Jul 22, 2009

  • 617 Answers

SOURCE: 2004 Dodge ram 1500, makes grinding noise in the

check wheel bearings

Posted on Feb 05, 2010

  • 14585 Answers

SOURCE: Loud clunk noise front front end when put into

You have a bad universal joint. you have to take the spindle off to replace this. once the spindle is off you can pull the shaft out. the universal has to be pressed out and back in. As far as the binding, that is normal in close tolerance turns. you get it alittle more with bad joints.
Randy

Posted on Nov 09, 2010

Testimonial: "THANKS A MILLION I WILL LOOK AT IT TONIGHT!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front end shakes and has a grinding noise


Need more detail please. What year, make, and model of car are you referring to? Does the front end only shake when the car is moving? Is it only above a certain speed? Do you feel the shake in the steering wheel or only in the car? Is the grinding noise all the time, only when turning, only when braking, etc.?

The more detail you can provide, the better chance you'll have of getting a decent answer.

Nov 26, 2016 | Cars & Trucks

1 Answer

What is causing the front end noise while in a hard turn (left or right) on my 2004 Toyota Sequoia?


The power steering pump capacity on some motor vehicles is unable to sustain full flow for more than a few seconds which could account for the noise which is the pump 'cavitating'. You might check the power steering reservoir fluid level in any case and read your car handbook for any warnings. I once owned a Mitsubishi Magna which had this limitation.

Nov 13, 2014 | 2004 Toyota Sequoia

1 Answer

Dragging feeling in rear, grinding noise


I NEED TO KNOW WHICH JOINTS U REPLACED EXACTLY AND WHEN.IS THET NOISE COMING WITH THE STEERING WHEEL TURNED ALL THE WAY TO ONE DIRECTION?DO U FEEL LIKE SOMETHING IS KICKING THE CAR?IF SO LET ME KNOW

Mar 09, 2014 | Volkswagen Touareg Cars & Trucks

2 Answers

2006 CHEVY COBALT FRONT END NOISE


The top of the strut mount was not installed properly.

Jan 09, 2014 | 2006 Chevrolet Cobalt

1 Answer

Clunking noise steering


check for loos steering rack , steering ball joints and front end problems.

Dec 19, 2013 | Cars & Trucks

1 Answer

I have a 2004 Yukon Denali there is a ticking noise I hear when I start up ... the ticks get faster as I accelerate ... and slow down at idle ... any suggestions??? thank you


Ticking noise that vary with the rpm indicates a tappet/ cam follower fault or worn rocker bushes and shafts . Where teh racker touches the valve end may be worn and have a spot that is slippng on the valve end and taking up the wear.. Check the top end for this problem. Check for bits loose on the drive belts and if you have a rubber timing belt check it out also

Oct 22, 2013 | GMC Cars & Trucks

1 Answer

Clunking noise when turning steering wheel going slow around corner


A lot of these Chrysler Town and Country vans had issues with the front stabilizer bar end links, usually you wont feel them move if you try to move them by hand, but they will make an awful noise clunk noise when turning or going over bumps slowly, i would suggest replacing the end links and that should take car of your clunking issue. Also the front lower control arm bushings separate as well and can cause this noise as well.... but i would replace the end links as a first step and go from there.... Hope this helps..

Sep 27, 2012 | 2003 Chrysler Town & Country

1 Answer

Noise in front end when going straight or turning right. Noise stops when you turn left.


i would check the right front wheel bearing . Jack the right side up and feel the tire pull back and forth and see if the tire feels loose if it does the wheel bearing is junk. only other thing check the cvc axel.

Mar 26, 2011 | 2007 Buick Lucerne CXS Sedan

1 Answer

Vibration and noise from front end while driving


Jack up the front end and put stands under it and block rear wheels. Look at axle boots and see if they are cracked. Try turning wheel back and forth sharply and see if you can hear any clicking. Problem could be outer axle joints. If the boots are cracked or you hear a clicking noise you will have to replace the axle. The axle and boot come as a complete unit. Please let me know what you find out.

Apr 13, 2009 | 2002 Chevrolet Venture Passanger

1 Answer

Front end makes clacking noise


If the clacking noise gets louder when turning its the drive joints at the front wheels

Jun 17, 2008 | 2002 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...