Question about Cars & Trucks

Open Question

How to remove ignition barrel from holden hk - Cars & Trucks

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mcgyver468
  • 710 Answers

SOURCE: Removal of the ignition Barrek

HAVE YOU TRIED TO USE SOME SILICONE SPRAY ON THE NUT? MAYBE YOU CAN CUT THE NUT OFF WITH A DREMEL AND A VERY SMALL DIAMOND BIT WITHOUT CUTTING THE DASH. HOPE THIS HELPS. LET ME KNOW. GOOD LUCK

Posted on May 03, 2009

Ad
  • 135 Answers

SOURCE: I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING

it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

Posted on May 20, 2009

  • 4 Answers

SOURCE: mercedez 190 ignition barrel. I have taken out ignition barrel attached to steering coloum but i can not remove key ignition from steering coloum how does it remove ignition barrel from steering

Should be the same as w123 model. Check diy Mercedes web page.
Photos included easy to do.

Posted on Jul 07, 2009

e-Guru
  • 3917 Answers

SOURCE: how to remove jammed ignition barrell from 1992,

Hi

you can access the ignition switch from underneath the dash, but it is easier to remove the steering wheel, then the instrument cluster. There are two basic elements to the ignition switch. The part that usually breaks down first is the front section, where the key goes into. You have to remove the entire unit from its bracket. Unplug the wire loom from the back of the housing. I believe there are two screws holding both sections together. Remove the screws and replace the unit. Then re-assemble.

Please check the link bellow :-

http://www.ehow.com/how_5833556_remove-mercedes-ignition-switch.html


Please accept the solution if it’s helpful. Do get back to us for any further query.
Thanks for contacting fixya.com

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Commodore. Why doesn't it start?


Did u get the key with the barrel...... If not the key may have to be coded to the barrel.... I.e immobiliser is not letting the car start... Try leaving the key in the ignition with the lights displayed on dash for two hours then try and start it.... See how you go

Feb 22, 2016 | Holden VT Cars & Trucks

1 Answer

How to remove hq holden ignition barrel


Hi from memory, you have to remove the steering wheel, then drop the column and remove the wires to the ignition, then remove the bolts that hold the steering cover and you should see why to do from then, hope this helps

Jul 08, 2014 | Holden Cars & Trucks

1 Answer

How to remove ignition barrel from Holden Astra Sedan


Just replace the key faub. or try disconnecting the neg battery cable for about 5 min and then re connect it and it may reboot the system

Jan 01, 2014 | Cars & Trucks

1 Answer

I have a vt commadore can I take out the ignition barrell without a key.


yes but it means removing the exterior part also by undoing the anti tampering bolt on the clamp that holds the whole barrel to the steering column and replacing the assembly

Sep 15, 2013 | 1998 Holden VT Commodore

1 Answer

How do i put my ignition barrel back in when the steering lock is stuck on car vt commodore 98


if the barrel is removed on the inside is the steering lock pin use small screwdriver to push it down while slightly moving the steering wheel until it goes down and stays down then you will be able to put in the barrel

Sep 09, 2013 | 1998 Holden VT Commodore

1 Answer

Remove ignition barrel in vt commodore


you need to have the key in the ignition take the shrouds off there is a small hole underneath the barrell you have to push something small into the hole then pull out the barrell

Apr 09, 2013 | 1998 Holden VT Commodore

2 Answers

How do i take out my ignition barrel 98 vt


to remove you ignition barrel is a simple process you need to remover the steering column covers from around the ignition switch.
there is a small hole located in the ignition barrel you will need to gentle push and hold an Allen key in the hole and rotate the key to the accessories the barrel should be come lose and gentle be pulled out.
please note that if the internal locking mech is not correctly depressed you will not be able to remove the barrel.
also if you have lost you key you will not be ale to remove the ignition barrel and will need to get a lock smith to rplace the whole thing witch can cost from $120 up to $250 depending on the locksmith

Jan 02, 2013 | 1998 Holden VT Commodore

1 Answer

How to remove barrel,demonstration


remove the steering lock barrel can only be done with the original key and the ignition in the acc position .this can be done in situ but some motors like VW you have to drill the hole to push the pin in so you need to know where it goes and to get to it you have to remove the steering column

Oct 13, 2012 | 1998 Holden VT Commodore

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...