Question about 1992 Isuzu Rodeo

1 Answer

Tranny problems i just put a clutch in my 92 rodeo, it was making a grinding sound only when giving gas, taking foot off gas,it stops when pressing on clutch pedal. after installing the new one it still makes this noise. it to me sounds as if a bearing was missing a ball {this is the noise it makes to me} if you have any idea please let me know

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 49 Answers

Did you change the bearing in the flywheel the center one or throw out bearing that pushes out on to the presserplate

Posted on Jan 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 92 Toyota paseo manual transmission is making a bad scraping/ grinding noise when I start the car and it is in neutral. Upon first pushing the clutch it stops, then resumes when I release the clutch. I...


automatics do not have a clutch that you can use in a manual transmission car. pull the tranny drain plug and look for metal bits on the magnet in the plug. If so it will be input shaft bearing that has failed. To fix that the tranny will have to come out and be repaired.

Nov 25, 2013 | Cars & Trucks

3 Answers

Hi my rx8 is makin a grinding noise from the gearbox and the noise goes away wen foot is pressed on the clutch makes a noise wen drivin in 1st 2nd 3rd n 4th gear noise goes in 5th and the noise is there in...


What?! Really! The noise goes when the clutch pedal is depressed! So the noise goes when the release bearing (throw-out bearing) is engage? So how would that be a release bearing/clutch problem? If it didn't make a noise until the clutch pedal was depressed, it would be the release bearing! In other words its the input shaft bearing and/or counter shaft bearing in the gearbox. Stop giving people bad advice

Mar 11, 2011 | 2004 Mazda RX-8

1 Answer

I have a manual transmission in my '04 Mustang. When I begin to depress the clutch, an odd grinding sound starts, not loud but enough to warrant concern. As I drive, the car sounds fine. Switching gears...


Worn throw out bearing, replace or the problem may damage other components. This requires dropping the entire transmission. this bearing sits between the clutch pressure plate and clutch slave assembly. When the clutch pedal is pressed, the bearing makes contact with the spinning clutch pressure plate. If defective, grinding/squealing noises may be heard. If the bearing fully fails, loose debris may damage other components. Replace immediately!!

Dec 11, 2010 | 2004 Ford Mustang

2 Answers

It is difficult to put into gear from a stop and while downshifting. 2000 mustang V6


check gear fluid in the tranny, brake fluid in the clutch master cylinder. after that check slave cylinder and linkage

Jul 30, 2010 | Ford Mustang Cars & Trucks

2 Answers

I have a 92 2 wheel drive Toyota pick up 5 speed transmission 2.4 liter engine. When I let up on the gas while in gear there is clicking/rattling noise in all gears except 4th gear. If I push down on the...


Sounds like you have a defectine cluthch componant. Best way to verify is get the rear axle off the ground . So as not to let the rear drive wheels make contact with the ground. Have an assistant start the truck and put it in gear. After making sure the vehicle is secure crawl under the vehicle and listen to comfirm that the noise is coming from the clutch area.

Mar 25, 2010 | 1992 Toyota Pickup

1 Answer

Clutch peddel wont depress when you put your foot on it it makes a grinding noise


Throwout bearing is gone , and /or the clutch/pressure plate is damaged.

Mar 11, 2010 | 2002 Isuzu Rodeo Sport

1 Answer

Grinding sound on pressing clutch in at high revs


The grinding sound may be a throw out bearing or the pilot bearing. The sticking throttle problem sounds like a linkage or cable binding up from possibly damage due to the impact from the accident.

Feb 05, 2009 | 2008 Toyota Yaris Sedan

1 Answer

Revs wont go higher than 2000rpm


Sounds like a MAF sensor problem, clean it 1st, if no change replace it.

Nov 13, 2008 | 1995 Ford Mustang

1 Answer

Transmition grinding when i go fast then either go into neutral or take foot off gas


Sounds like the trans imput shaft bearing. They tend to wear and cause shifting problems. It also could be synchronizers. Marlin Crawler makes aftermarket trans bearings for these transmisions.
www.marlincrawler.com
I hope this helps. Also check tranny fluid and clutch. a worn or bad clutch will also cause this.

Nov 07, 2008 | 1992 Toyota Pickup

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...