Question about Cars & Trucks

1 Answer

CPS crankshaft position sensor for a 1999 Chrysler Cirrus 2.5l v6 How do u get to the sensor and what is the steps to take to get it installed It is located in the back of the back of the engine. T

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,341 Answers

Here is info on a '96 Cirrus with same 2.5L engine. Check to see if same as yours.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528008987d

Posted on Dec 30, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
co7196
  • 3433 Answers

SOURCE: need location of crankshaft position sensor on a

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Posted on Sep 28, 2009

  • 80 Answers

SOURCE: I need a diagram of the location of the crankshaft position sensor for 1997 chysler cirrus 2.5 liter engine

try google and ask the question "where is the location of the crankshaft position sensor for 1997 chysler cirrus 2.5 liter engine" or you can go to a parts store and ask for there help, or buy a repair manual it will show you the location.

Posted on May 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of cps on a 1999 chrysler concord 3.2


The crankshaft position sensor is located on the passengers side of the transmission housing, above the differential housing. The bottom of the sensor sits above the drive plate/flexplate/flywheel.

Sep 18, 2017 | Chrysler Cars & Trucks

1 Answer

1999 CRYSLER CIRRUS,REPLACED THE CRANKSHAFT SENSOR BUT STILL NO SPARK


try the auto shutoff relay.. it controls the fuel pump and the igniton circuits..

Dec 15, 2013 | 1999 Chrysler Cirrus

1 Answer

I need a diagram of the location of the crankshaft position sensor for 1997 chysler cirrus 2.5 liter engine


try google and ask the question "where is the location of the crankshaft position sensor for 1997 chysler cirrus 2.5 liter engine" or you can go to a parts store and ask for there help, or buy a repair manual it will show you the location.

May 28, 2012 | Cars & Trucks

2 Answers

How do you replace the crankshaft positioning sensor?


well you did not list the engine . so here is all of them on the 2.0 or 2.4- 4 cyl the crank sensor is located behind the generator just abouve the oil filter mounted to the eng block. on the 2.5 V6-remove the speed control servo from the drivers side strut tower. (its located just under the distributer) remove the retaining bolt and pull the sensor straight up out of the transaxle housing

Jan 27, 2011 | 1998 Chrysler Cirrus

1 Answer

No fire at distributor


The 1997 Chrysler Sebring 2.5L has a distributer with an intergrated coil. All other models have a distributerless ignition ("coil packs").

Start by testing the ASD (Automatic Shut Down) relay, then the CPS (Crankshaft Position Sensor) and CMH (Camshaft Position Sensor).

The CMH test the same way likethe CPS; the ASD is located on cowl, at left rear of engine compartment.

Hope helps.

Jul 28, 2010 | 1997 Chrysler Sebring

1 Answer

Where is the crankshaft sensor located on 1999 v6 hyundai sonata?


The CPS for these motors is located in the front of the engine and the the timing belt cover needs to be removed to gain access. If you need further instructions on removal as well as diagrams, email me at iambanshee74@yahoo.com and I will send those immediately.

Jul 13, 2010 | 1999 Hyundai Sonata

1 Answer

Where is the crankshaft position sensor located on a 2000 Sebring Conv.


removal steps (CPS) -remove air intake hose -Battery tray -Crankshaft position sensor

Apr 27, 2010 | 2000 Chrysler Sebring

1 Answer

1999 CRYSLER CIRRUS NO SPARK,CHNAGE CRANK SENSOR,DIST, CHECK POWER/GROUND CKT OK


Either ASD relay in the fuse box in the front driver's side engine compartment or a burnt wire on the harness on the back of the motor going to the crankshaft position sensor.....
The relay can be swapped with one of the other relays because they are the same ones in the fuse box.

Oct 08, 2009 | 1996 Chrysler Cirrus

1 Answer

Need location of crankshaft position sensor on a 1996 chrysler cirrus v6 location on engine and how to find it


The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Sep 28, 2009 | 1996 Chrysler Cirrus

1 Answer

Check engine light comes on


Code 12 means That the Crankshaft position sensor may need replacement.It is located near the crankshaft maybe under the timing cover.

Apr 07, 2009 | 1995 Chrysler Cirrus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...