Question about 2000 Ford Windstar

1 Answer

Hormontic balancer bar - 2000 Ford Windstar

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,316 Answers

The harmonic balancer is a special pulley on the front of the crankshaft.

Posted on Dec 30, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install balance drive gear on crankshaft 2007 Camry 2.4


Remove old crankshaft pulley ( Harmonic Balancer), by putting sturdy socket,think its 19mm, or 3/4 " on the center crankshaft bolt, with a good size breaker bar, wedge the breaker bar in between the suspension, and drive axle, to keep the breaker bar from spinning, while, you now turn the key inside the car, to engage starter, to spin the crankshaft,which may take several attempts, of turning the key, and putting socket back on, they are very stubborn,to break the center bolt loose,
Then remove harmonic balancer, with a PULLER, which requires 2 bolts, in the threaded holes, one on each side of the now empty center bolt hole, autozone , advance, has these to loan out, only requires deposit, which they give back to you, when you return it.
Put square key in slot on bare crankshaft, slide harmonic balancer,(crankshaft pulley,while lining up the square key,and tighten crankshaft bolt.

Oct 24, 2014 | 2007 Toyota Camry

1 Answer

Do you have to pull harmonic balancer off to replace crankshaft position sensor on a 93 suburban 5.7


Yes you do....its right behind the harmonic balancer, note...do not use a pry bar to remove the balancer......

Jun 12, 2014 | 1993 Chevrolet K1500

2 Answers

How do i remove the harmonic balancer bolt to replace the timing cocer gasket on a 1999 ford tarus se


If there is no air-compressor and an impact gun to remove the harmonic balancer bolt, then there are two other ways to remove it. Either remove the inspection cover at the bell-housing and use a large flat head screwdriver to wedge between the flex-plate drive gear teeth and the engine block so that the engine is locked-up, and then remove the harmonic balancer bolt with a long breaker bar and a lot of muscle power, or for the more advanced mechanics and only they should attempt this, place a long breaker bar on the harmonic balancer bolt and then brace the breaker bar up against the frame of the vehicle so that when the engine turns over the breaker bar will stop on the vehicle frame, and keep in mind that the crankshaft will turn clockwise or to the right, and when you are looking for some place to brace the breaker bar be sure that nothing else will get in the way or it will be damaged. Be sure that the breaker bar is on the harmonic balancer bolt properly, and place the breaker bar about 1 to 2 inches from the vehicle frame so that when the engine turns the breaker bar will lock up against the vehicle frame, and while holding the breaker bar in place have someone turn the ignition key and give the starter a bump, and be very sure to keep your hand away from where the breaker bar is going to contact the vehicle frame, or your fingers will get smashed by the breaker bar when it turns into the frame so do not attempt this if you are unfamiliar with using hand tools, and the starter should break the harmonic balancer bolt loose easily, so be very sure that your hands are out of the way of getting hurt when the starter motor is used to break the harmonic balancer bolt loose.

Sep 13, 2010 | Ford Taurus Cars & Trucks

3 Answers

I have a 2002 jeep wrangler that seems to start shaking at 60mph below or over ok. It is not major but noticeable. Where do I start looking? Thanks Dan


Grab hold off the prop-shaft to see if it is quite solid, it could be a worn UJ. Check the balance weight on the same shaft to ensure it hasn't slipped forward or backwards on the shaft.
Then get wheels checked, they could need re-balancing.

Nov 26, 2009 | 2002 Jeep Wrangler

1 Answer

How do i remove the old harmonic balancer on a 1994 honda accord lx


First, look at the direction the balancer turns. Remove the belts. Put the proper sized socket on the balancer bolt and, install a breaker bar into the socket. Make sure the bar is at the side of the engine compartment, where the top of the balancer rotates toward. Next, BUMP THE KEY but DO NOT crank the engine. When the bar contacts the wall or other object, it will stop, allowing the engine to continue and break the bolt loose.

Oct 13, 2009 | 1994 Honda Accord

3 Answers

Front end shakes at 50mph, possible stabalizer bar,


Do a replacement. There is no way to adjust the bar.

Aug 24, 2009 | 2006 Jeep Wrangler

1 Answer

Replacing the harmonic balancer in ford bronco 1985 how do i replcace it


First remove radiator fan shrould.This will give you access to the fan.Remove fan and fan belts.Remove bolt on harmonic balancer.You will need to rent a balancer remover and installer kit.Most big auto parts chains will rent these kits to you.Next remove four bolts holding pulley to balancer.Next attach balancer puller to balancer with long bolts from kit.Using a 1\2 drive breaker bar,remove balancer from engine.After removing balancer replace front seal.Lubricate hub on new balancer with engine oil.Then use installation tool from kit to install balancer.Never try to beat balancer on with hammer,engine damage could occur.Then work in reverse to replace remaining parts.Hope this will help you.

Aug 03, 2009 | Ford Bronco Cars & Trucks

2 Answers

My 1996 dodge neon's crank balancer will not come off. i need to take this off to get the timing belt off. to fix a blown headgagsket.


Take everything in front of it off.  Use a long breaker bar and socket, 1/2" drive, 3/4" if you have one.  Put the socket on the nut and the bar across to a piece of the frame.  BUMP the starter.  DO NOT CRANK IT.  This will break the nut loose.

Jul 09, 2009 | 1996 Dodge Neon

1 Answer

Harmonic Balancer


I have had the balancers come off just by unbolting it, and popping it off with a pry bar. Other times, I have used 2 pry bars, each behind the pulley, and popped it off. A few times, I have had to get out the puller. Just depends how long the balancer was on, and how rusty it is. But, they are not so tight that a puller will not do the job. Try the 2 pry bars, that usually works. Hope this helps, and thanks for choosing FixYa. The graciousness of a FixYa rating would be greatly appreciated. Thanks.

Nov 06, 2008 | 1993 Toyota Camry V6

2 Answers

While accelerating,the vehicle hesitate and even jerks


Hesitation,jerking,acts as if it's not getting fuel? Have the egr/coil checked! I had same problem,thought it might be injectors,after delving deeper into it,I found the coil was defective

Jun 04, 2008 | 1999 Ford Expedition

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...